• Journal of Welding and Joining
• /
• v.14 no.4
• /
• pp.79-88
• /
• 1996

For improvement in productivity and weld quality, weld seam tracking and welding parameter control are very essential in the welding of a structure which can not be cxactly fit-up due to mismatch, discontinous gap, deflection, etc.. In this study, an automatic weld seam tracking system is developed for I-butt joint structure, and the system consists of XYZ working table, vision sensor and user interface program. In the developed vision sensor system, an image projection algorithm for weld-line detection and an adaptive current control algorithm for gap variation were implemented. The user interface program developed in this study by basing on the objct oriented concept could provide very convenient way to utilize the tracking system with the pull-down menu driven structure. The developed system showed a good seam tracking and weld quality control capability corresponding to deflected weld lines and gap variations.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.5
• /
• pp.302-309
• /
• 2000

The tracking characteristics of silicone rubber degraded by accelerated outdoor exposure employing a weather-o-meter were investigated. The tracking test was performed according to ICE Publ.587 method but the concentration of conductive solution was two times higher than IEC standard in order to accelerate the tracking failure. The number of large effective scintillation and the current of high voltage circuit were measured simultaneously. It was shown that the number of effective scintillation had valuable information of the tracking degradation state of silicone rubber, while the average current between electrodes could not provide information enough for diagnosis. Based upon the experimental results, it could be said that the key factor accelerating tracking failure was not Joule heating by current but pyrolysis by burning of silicone rubber, and that reduction of contact angle was due to chain scission which resulted in the free radicals of low molecules.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.617-621
• /
• 2001

This paper presents a maximum power point tracking algorithm for Photovoltaic array using only instantaneous output current information. The conventional Hill climbing method of peak power tracking has a disadvantage of oscillations about the maximum power point. To overcome this problem, we have developed a algorithm, that will estimate the duty ratio corresponding to maximum power operation of solar cell. The estimation of the optimal duty ratio involves, finding the duty ratio at which integral value of output current is maximum. For the estimation, we have used the well know Lagrange's interpolation method. This method can track maximum power point quickly even for changing solar insolations and avoids oscillations after reaching the maximum power point.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.917-922
• /
• 2003

In this paper, a high speed rotating arc sensor for automatic fillet welding is introduced. In order to track the welding seam, The high speed rotating arc sensor is used. The welding tip of a high speed rotating arc sensor rotates about 3000 rpm using DC motor. The rotating torch is driven by gear between welding torch body and wire guide. The welding current is measured by using the current sensor and rot at ing position sensor. To realize the welding seam tracking algorithm with accuracy, a software filter algorithm using the moving average method is applied to the measured welding current in the microprocessor. The welding mobile robot with two wheels and two sliders is developed for fillet welding. The welding mobile robot can control its traveling direction and turn itself around the corner. The effectiveness is proven through the experimental results conducted with varied fillet tracking patterns.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.155-161
• /
• 2002

This paper presents a maximum power point tracking algorithm for Photovoltaic array using only instantaneous output current information. The conventional Hill climbing method of peak power tracking has a disadvantage of oscillations about the maximum power point. To overcome this problem, we have developed an algorithm that will estimate the duty ratio corresponding to maximum power operation of solar cell. The estimation of the optimal duty ratio involves, finding the duty ratio at which integral value of output current is maximum. For the estimation, we have used the well know Lagrange's interpolation method. This method can track maximum power point quickly even for changing solar isolation and avoids oscillations after reaching the maximum power point.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1191-1192
• /
• 2006

This paper propose method of maximum power point tracking using boost converter for a connected single phase inverter. The maximum power point tracking control is based on generated circuit control MOSFET switch of two boost converter and single phase inverter uses predicted current control to control four IGBT's switch in full bridge. The predicted current control provide current with sinusoidal wave shape and inphase with voltage.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.224-225
• /
• 2007

In this paper proposed method of maximum power point tracking using boost converter for a connected single phase inverter. The maximum power point tracking control is based on generated circuit control MOSFET switch of two boost converter and single phase inverter uses predicted current control to control four IGBT's switch in full bridge. The predicted current control provide current with sinusoidal wave shape and inphase with voltage.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.131-139
• /
• 1996

The response of the arc sensor using the welding current and/or welding voltage as its outputs has been obtained by the analysis and/or experiments of the static characteristics of arc sensor. But in order to improve the reliability of arc sensor, it is necessary to know its dynamic characteristics. So in this paper, it is presented the dynamic model of arc sensor including the power source, arc voltage, electrode burnoff rate, and wire feed rate. A numerical simulation of the dynamic model of arc sensor was implemented, computing the welding current with input of CTWD. The results of computer simulations and experiments of $CO_2$arc welding showed that a linear relationship between weaving center - weld line distance and current area difference was established. Additionally, a real-time weld seam tracking system interfaced with industrial welding robot was constructed, the result of the weld seam tracking experiment for weld line with an initial offset error of 5$^{\circ}$was good.

• The KIPS Transactions:PartB
• /
• v.14B no.7
• /
• pp.473-480
• /
• 2007

Feature tracking in video frame sequences has suffered from the instability and the frequent failure of feature matching between two successive frames. In this paper, we propose a robust 2D feature tracking method that is stable to long video sequences. To improve the stability of feature tracking, we predict the spatial movement in the current image frame using the state variables. The predicted current movement is used for the initialization of the search window. By computing the feature similarities in the search window, we refine the current feature positions. Then, the current feature states are updated. This tracking process is repeated for each input frame. To reduce false matches, the outlier rejection stage is also introduced. Experimental results from real video sequences showed that the proposed method performs stable feature tracking for long frame sequences.

• Journal of the Korean Society of Safety
• /
• v.24 no.4
• /
• pp.28-33
• /
• 2009

This study examined the mounting status of cigar lighter receptacles for vehicles and analyzed the tracking phenomenon that occurs when foreign material entered a cigar lighter receptacle to obtain data for the analysis of accident investigation. Regardless of the vehicle's output, cigar lighter receptacles are mounted in a vehicle horizontally, vertically, or at tilting or inclined angle. The tilting type cigar lighter receptacle is much easier to use but current leakage resulting from foreign materials (coffee, beverages, water, etc.) falling into the cigar lighter receptacle may cause a fire to start. This study used a vehicle battery (DC 12V) as a power supply for the tracking test and configured its circuit in the same way as that of an electrical device in a vehicle. The tracking phenomenon that occurred in the standby mode of the vehicle exhibited a fine flame and an irregular occurrence of smoke. While this tracking phenomenon was occurring, the leakage current and the reaching distance of the flame were measured to be approximately 930mA and $20{\sim}50cm$, respectively. It is thought that the resultant flame may ignite toluene, dust, cigarettes, etc. It was observed that as the tracking progressed, the internal metal socket melted and a hole was created, the surface of which was also severely carbonized. In addition, the electrical resistance of the carbonized conductive path was measured to be approximately $30{\Omega}$. It is thought that this much resistance may cause local heating when leakage current flows and could ignite any nearby flammable material.