• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 마케팅과학연구
• /
• 제19권3호
• /
• pp.49-61
• /
• 2009

本文为执行官提供了他们在处理日常业务问题和市场机会时如何阐述自己思考过程的培训. 本研究建立在Schank提出的教学基础上, 包括: (1)经验学习和最好的指导提供给学习者从诸如全球背景, 团队项目和专家经历等的互动的故事提炼知识和技能的机会. (2) 告诉不会导致学习, 因为在学习需要的行动训练环境中, 应强调积极使用故事, 案例和项目. 每个培训案例包括执行官解释自己的决策系统分析(DSA, 还需要执行官做DSA简报. 在训练时要求执行官写DSA简报. 在执行官学员写书面报告的说明中包括(1) DSA路线图的本质的细节(2) 警告和机会的陈述, 读者的行政地图及图内的DSA解释. 该报告的最大长度为500字, 其规则就是使行政人员培训课程行之有效. 引言之后是第二部分文献综述, 简要地总结了有关人们在对问题和机会的背景下的想法及文献. 第三部分通过使用对不同的贴牌生产客户定价相同的化学产品的培训练习来解释DSA的起源和过程, 第四部分展示一个炼油设备公司订价决策的培训练习. 第五部分提供一个商业客户办公家具采购的市场策略案例. 第六部分是结论和建议. 这些建议是关于使用培训课程和发展其他培训课程来磨练执行官制定决策的能力. 文章引导读者利用工具箱研究综合的报告, (DSA)路线图根据生态合理性理论将战略与环境相匹配. 这三个案例的研究让学习者在意愿层面征求建议来作出决策. Todd and Gigerenzer 提出人们使用简单启发式,因为他们在自然的决策环境中通过探索信息的结构使适应性行为有可能产生. "简单是一种美德, 而不是诅咒", 有限理性理论强调了西蒙的命题中心, "人类理性的行为仿佛一把剪刀, 其刀片则是任务环境的结构和执行者的计算能力". Gigerenzer的观点和西蒙的环境的危害相关, 也和本文中三个环境结构的案例相关. "环境这个词, 在这里, 并不是指总的物理和生理的环境, 而只是指被给予需要和目标的重要有机体 本文关注了结合任务环境的结构和使用适应的工具箱启发的报告. (DSA)路线图根据生态理性理论将战略与环境相匹配. 渴望适应理论是这一方针的核心. 渴望适应理论将决策制定作为一个没有把目标整合的多目标问题模拟成一个把所有决策选项进行完全的优先顺序化. 这三个案例研究让学习者在意愿层面征求建议来作出决策. 渴望适应用一系列的调整步骤的形式. 一个调整步骤通过仅一个目标变量的变化就可以改变在渴望网格上邻近点当前的渴望水平. 上调步骤是目标变量的提高, 下调步骤是目标变量的下降. 创造和使用渴望适应水平是对有限理性理论的整合. 文章通过提供学习者经验和实践环节增加了意愿采纳和有限合理性的理解和特点. 利用DSA图排列CTSs和撰写TOP可以清晰和深化Selten的观点 "清晰, 意愿采纳必须作为研究的解决方案整合到整个蓝图中". 这些有限理性的研究许可了在现实生活中为什么, 如何作决策的理论和在自然的环境中利用启发式的学习训练两方面的发展. 本文中的练习鼓励根据不同使用目的学习快速而简洁的启发式技巧和原则. 这也正回应了Schank的思想 "从本质上来看, 教育不是让学生们知道发生了什么, 而是让他们感受到所发生的事情. 这不容易做到. 在如今的学校教育是没有情感的, 这是一个很大的问题". 这三个案例和附加的练习问题遵守了Schank的观点. "这种教育过程最好是通过参与他们其中来实现, 也可以这样认为, 精神层面的积极讨论".

• Tuberculosis and Respiratory Diseases
• /
• 제44권4호
• /
• pp.853-860
• /
• 1997

연구배경 : 만성 기침은 임상에서 흔한 증상으로 대부분은 후비루증(posterior nasal dripping : PND), 천식, 위식도 역류증, 기관지염 등으로 인한 것으로 알려져 있다. 만성 기침 환자 중 일부분은 기침과 동반하여 천명이나, 호흡곤란 등과 같은 기관지 천식과 유사한 증상을 경우가 많아 기관지 과민반응 검사를 시행하게 된다. 기관지 과민반응 검사는 대부분 $FEV_1$을 측정하지만 흉곽외 기도의 과민반응은 측정하지 못하는 단점이 있다. 본 연구는 만성 기침 환자를 대상으로 기관지와 흉부외 기도의 methacholine 유발 검사를 시행하여 기도 과민 반응을 평가하여 상관 관계를 알아보고자 본 연구를 시행하였다. 대상 및 방법 : 대상 환자는 2개월 이상 기침이 있는 111명의 환자를 대상으로 하였으며, 남자 55명, 여자 56명으로 평균 연령은 $37.4{\pm}13.0$세였다. 대상 환자는 심혈관 질환, 전신 질환 등이 없었으며, 과거에 기관지 진단 받은 병력이 없고 기관지 확장제나 사용한 병력이 없었던 환자였다. 기침이나 천명 또는 간헐적인 호흡곤란 등의 증상은 문진으로 확인하였고, 기침만 존재한 환자 46명, 기침과 천명이 있는 환자 24명, 기침과 호흡곤란이 있는 환자 22명, 기침, 천명 및 호흡곤란이 있는 환자 19명이었다. 대상환자의 폐기능검사는 $FEV_1$(%) $106.5{\pm}15.3$, FVC(%) $100.1{\pm}12.8$, $FEV_1$/FVC(%) $106.3{\pm}13.1$로 정상이었다. Methacholine 유발검사는 0.0625 에서 25 mg/ml의 2배수 농도를 흡입한 5분후 기관지 과민 반응은 $PC_{20}FEV_1$으로 측정하였고, 흉곽외 기도 과민 반응은 최대 중간흡입 기류속도인 $MIF_{50}$으로 측정하여 연속 3회 감소하고 25%이상 감소한 $PC_{25}MIF_{50}$으로 측정하여 25mg/ml 이하의 농도에서 양성인 경우를 기관지(BHR) 및 흉부외 기도(EAHR) 에 각각 반응이 있다고 판독하여 대상 환자의 상관 관계를 확인하여 다음과 같은 결과를 얻었다. 결 과 : 대상 환자 총 111명중에 기관지 과민반응(BHR)이 27명, 흉곽외 기도 과민반응(EAHR)이 16명, BHR과 EAHR이 함께 있는 환자 8명으로 과민 반응이 있는 환자는 총 50명이었으며, 그외의 61명은 기관지와 흉부외 기도의 과민반응이 없었다. BHR 또는 EAHR이 양성인 환자 50명중에 기침만 있는 환자는 BHR이 3명, EAHR이 9명, BER과 EAHR이 같이 있는 환자는 2명으로 EAHR이 가장 많았으며, 기침과 천명이 있는 환자는 BHR이 10명, EAHR이 2명 및 BHR과 EAHR이 같이 있는 환자는 2명으로 BHR이 가장 많았고, 기침과 호흡곤란이 있는 환자는 BHR이 7명, EAHR이 3명, BHR과 EAHR이 같이 있는 환자는 1명으로 BHR이 가장 많았다. 기침, 천명 및 호흡곤란이 모두 있는 환자는 BHR이 7명, EAHR이 2명, BHR과 EAHR이 같이 있는 환자는 3명으로 BHR이 가장 많았다. BHR와 EAHR이 모두 음성인 환자는 총 61명이었으며, 기침만 있는 환장 32명, 기침과 천명이 있는 환자 10명, 기침과 호흡곤란이 있는 환자 11명, 기침, 천명 및 호흡곤란이 모 두 있는 환자는 7명이었다. 결 론 : Methacholine에 양성 반응인 환자중 호흡곤란이나 천명이 동반된 만성 기침환자에서는 주로 기관지 과민 반응이 나타났으며, 기침 단독 증상인 환자에서는 반응이 존재함을 알 수 있었다.

• 항공우주정책ㆍ법학회지
• /
• 제30권2호
• /
• pp.201-248
• /
• 2015

우리나라는 항공수요의 증가에 따라 항공기내 불법방해 행위의 발생건수도 계속 증가하고 있는데, 2010년에 55건, 2014년에 354건이 발생하여, 지난 5년간 매년 평균 211건이 발생하였다. 1963년 항공보안에 관한 최초의 전 세계적 국제법률문서로서 새로운 "항공기내에서 범한 범죄 및 기타행위에 관한 협약"인 동경협약이 채택되었다. 동경협약이 발효된 1969년 직후 바로 1970년에 "항공기내 불법납치 억제를 위한 협약"인 헤이그협약이 채택되었고, 1971년에 "민간항공의 안전에 대한 불법적 행위의 억제를 위한 협약"인 몬트리올협약이 채택되었다. 2001년 9/11 사건이후 1971년에 채택된 몬트리올협약을 수정 보완하는 "국제민간항공과 관련된 불법행위억제에 관한 협약"인 2010년 베이징협약과 1970년에 채택된 "항공기 불법납치의 억제를 위한 협약"인 헤이그협약을 보충하는 2010년 베이징의정서가 채택되었다. 그 후 항공기내 난동행위의 심각성과 빈번함이 확대되고 있음에 따라 1963년에 채택된 "항공기내에서 범한 범죄 및 기타행위에 관한 협약"인 동경협약을 개정하는 2014년 몬트리올의정서가 채택되었다. 우리나라가 가입한 발효된 항공보안 관련 국제협약으로는 1963년 동경협약, 1970년 헤이그협약, 1971년 몬트리올협약, 1988년 몬트리올보충의정서, 1991년 가소성폭약표지협약 등이 있다. 우리나라는 1971년에 동경협약을 비준함에 따라 1974년에 항공기운항안전법을 제정하였고, 2002년 8월에 항공기운항안전법을 대체한 항공안전 및 보안에 관한 법률이 제정되었으며, 2014년 4월에 항공안전 및 보안에 관한 법률은 항공보안법으로 명칭이 변경되었다. 항공보안법은 본질에 있어서 1963년 동경협약과 1970년 헤이그협약의 이행입법이다. 또한 항공보안법상의 용어는 ICAO 회람장 288(Circular 288)의 모델입법 제1조 내지 제3조의 난동 및 방해 행위보다 넓다. 한편 항공보안법은 현대화된 항공보안 관련 국제협약인 2010년 베이징협약 및 베이징의정서 그리고 2014년 몬트리올의정서상의 국내입법 사항들을 상당부분 반영하고 있다. 그러나 앞으로 이들 국제협약들이 발효되고 우리나라가 가입할 경우 국내입법인 항공보안법 상 개정 또는 신설되어야 할 사항들로는 재판관할권, 비행 중의 정의, 기장 등의 소송상 면책, 기장 등의 범인 인도 의무화, 범법자의 처벌 강화, 공범의 적용확대 및 국제협약의 준수 등에 관한 규정을 들 수 있다. 이 들 가운데 특히 재판관할권의 범위에 관하여 우리나라 입법은 침묵하고 있다. 그러므로 항공기내 난동 및 방해 범죄의 영토외적 사건 등에 대하여 재판관할권이 확대되기 위하여 항공보안법이나 형법총칙을 개정하는 것이 바람직할 것이다. 결론적으로, 점차 지능화 및 다양화되어 가고 있는 항공보안 위협에 대응하기 위하여 우리정부는 항공보안 관련 국제협약의 내용 및 각국의 비준현황을 면밀히 검토하여, 우리나라의 협약 가입 및 협약 상 국내입법 사항의 이행을 위해 항공보안 관련 입법과 항공보안제도를 개선하도록 노력하여야 할 것이다.

• 헤리티지:역사와 과학
• /
• 제37권
• /
• pp.371-405
• /
• 2004

문화재의 국제적인 유통행위는 다수 국가가 관계되므로 이 문제 해결을 위해서는 국제법적인 접근이 필수적이다. 2차대전 이후 문화재의 가치가 물질적 가치에서 국가와 민족의 정체성 확립을 위한 정신적 민족적인 측면의 가치가 중시되면서 신생 독립국과 식민제국들 간에 문화재의 소유권 다툼이 쟁점화 되어 문화재 반환을 목적으로 하는 국제적인 협력과 법제도적인 장치의 모색이 필요하게 되었다. 문화재의 불법거래에 관한 국제협약으로 유네스코(UNESCO)를 중심으로 문화재의 준비적 보존의무를 부과하는 1954년 "전시 문화재 보호에 관한 협약", 문화재 반 출입에 대한 통제와 반출에 허가장 발급을 통해 불법 취득 유통 억제를 위한 1970년 "문화재불법 반 출입 및 소유권 양도의 금지와 예방수단에 관한 협약", 도난이나 불법적으로 반출된 문화재의 국제적 반환을 의무화한 1995년 "유니드로와 협약"이 있다. 또한 유엔(UN)의 산하 기관으로 유네스코(UNESCO)는 특히 소위 문화재 분과(the Division of Cultural Heritage)를 마련하여 문화재에 대한 관계업무 처리에 주력하여 오고 있으며, UN 총회 역시 1973년의 결의 3187 이후로 문화재 보호에 관하여 계속적인 관심을 표현하여 오고 있는데 그 기본내용은 문화재의 원산국에로의 반환에 관한 국제 협력을 확인하고, 각국에 예술품 및 문화재의 불법거래 금지 및 방지를 위한 적절한 조처를 권고하며, 자국내 문화재에 대한 목록화 작업을 권고함과 아울러 종국적으로 많은 국가가 유네스코(UNESCO) 협약의 당사국이 되어 국제적인 협력체제의 구성원이 될 것을 권장하는 것이다. 국제협약의 한계로 협약상의 문화재에 대한 정의 차이가 존재한다. 먼저 1954년 협약상의 문화재는 동산에만 국한되는 것이 아니라 부동산도 포함하고 있는데 1970년 협약은 그 제정 목적이 '문화재의 불법적인 반 출입 및 소유권 양도의 금지와 방지수단'의 강구에 있으며 따라서 그 규율대상도 원칙적으로 유형의 동산문화재(tangible movable cultural property)에 국한된다고 봐야할 것이다. 1995년 협약도 역시 동산문화재를 규율대상으로 삼고 있다. 이 두 협약은 이 점에서 1954년 협약이나 주로 부동산적인 특성을 갖는 문화유산 및 자연유산을 대상으로 하는 1972년의 협약과 차이를 보이고 있다. 이러한 차이는 문화재의 개념에 대한 내재적인 차이를 반영하는 것이 아니라 주어진 협약의 제정 목적 및 취지가 다름에서 기인하는 것이다. 우리나라의 경우 1866년의 병인양요, 일본에 의한 36년간의 식민통치, 군정기, 경제 개발기 등을 통하여 다수의 문화재가 해외로 유출되었다. 물론 이들 문화재를 전부 반환 받을 수도 없고 또 받을 필요도 없는 것이지만, 이들 중 일부는 한국 사회의 문화적 역사적 정체성의 형성에 중요한 역할을 한다거나 또는 이들의 외국(특히, 일본)에서의 소재가 과거 한국민에 대한 지배의 상징으로서 기능한다거나 할 경우 반환 문제가 제기될 수 있을 것이다. 이러한 경우에 우리의 입론을 강화하기 위해서는 1954년 협약 및 제1의정서의 비준은 적극적으로 고려해야 한다고 판단된다. 반환을 요구할 경우 우선 문화재의 도난 여부가 핵심이며 이 경우 국제협약에 따라 조치하면 될 것이지만 외교적 협상의 단계에 이르면 이 문제는 정치적 문제가 될 것이다. 이 경우 반환을 요구하는 국가는 상대국이 문화재를 반환하도록 유도해야 한다. 문화재의 불법거래 방지에 대한 절실한 필요성에 반해, 동북아 지역 국가 및 시민사회의 방지노력은 대단히 미흡한 실정인 바, 이를 실현하기 위한 국가 및 시민 사회적 차원의 체계적인 노력이 동아시아 지역 전체에서 활발하게 전개하여야 할 것이다. 문화재의 불법적인 거래를 가장 효과적으로 막을 수 있는 방법은 인터폴(Interpol) 회원국간 정보를 신속히 유통시키는 것인데 이를 위해서는 인터넷 기술에 바탕을 둔 통신 시스템을 개발해야 하며 도난당한 문화재의 불법거래를 방지하기 위한 보다 효율적인 방안으로 문화재 보호 법률의 도입, 국제협약의 가입, 수집품 목록 구축 등의 조치가 필요하다고 본다.

• 한국조경학회지
• /
• 제51권3호
• /
• pp.70-82
• /
• 2023

최근 IT 기술과 데이터의 범람으로 생활 전반적인 부분의 패러다임이 전환되고 있다. 이러한 기술의 발전과 변화는 학술영역에도 영향을 미치고 있다. 학문적 교류와 연계를 통해 연구주제나 연구 방법의 개선이 이루어지고 있다. 특히, 데이터 기반의 연구 방법이 다양한 학문분야에서 진행되고 있으며 조경학에서도 지속적인 연구가 필요한 시점이다. 따라서 본 연구에서는 이러한 시대적 상황을 반영하여 인공지능의 한 분야인 머신러닝을 활용한 경관 선호 평가 및 예측모델의 개발 가능성을 알아보는 것을 목표로 한다. 본 연구의 목표를 달성하기 위하여 경관 분야에 머신러닝 기법을 적용하여 경관 선호 평가 및 예측 모델을 구축하고, 구축된 모형의 모의정도를 검증하였다. 이를 위해 본 연구에서는 최근 신재생에너지 사업으로 주목받는 풍력발전시설 경관 이미지를 연구대상으로 선정하였다. 분석을 위하여 풍력발전시설 경관 이미지를 웹크롤링 기법을 활용하여 수집하고 분석 테이터셋을 구축하였다. 우수한 성능의 예측모델 도출을 위하여 머신러닝 분석에 활용되는 University of Ljubljana의 프로그램인 오렌지 버전 3.33을 활용하였다. 또, 머신러닝 학습데이터의 평가기준을 통합한 모델과 평가기준 별도 모델 구조를 활용하였으며, 머신러닝 분류모델에 적합한 kNN. SVM, Random Forest, Logistic Regression, Neural Network 알고리즘을 사용해 모델을 생성하였다. 생성된 모델을 성능 평가를 실시하여 본 연구에 가장 적합한 예측모델을 도출하였다. 본 연구에서 도출된 예측모델은 경관의 유형에 따른 분류, 경관과 대상의 시거리에 따른 분류, 선호에 따른 분류 등 3가지 평가기준을 별도로 평가 후 종합해 예측하여 결과를 도출하였다. 연구 결과 경관 유형에 따른 평가 기준 정확도 0.986, 시거리에 따른 평가 기준 정확도 0.973, 선호에 따른 평가 기준 정확도 0.952에 달하는 높은 정확도를 가진 예측모델을 개발하였으며, 평가데이터 예측 결과를 통한 검증과정을 보아도 모델의 성능 치를 상회하는 성과를 도출했음을 알 수 있다. 경관 관련 연구에서 머신러닝을 활용한 예측모델 개발 가능성을 알아본 실험적 시도로 이미지 데이터의 수집 및 정제를 통해 데이터 세트를 구축하여 높은 성능의 예측모델이 생성 가능하며, 이후 경관 관련 연구 분야에 활용될 수 있다는 가능성을 확인할 수 있었다. 본 연구의 결과와 시사점, 한계점을 반영한다면 풍력발전시설의 경관뿐만 아니라 자연경관이나 문화경관 등 다양한 형태의 경관 예측모델 개발이 가능할 것으로 생각되며, 경관 유형에 따라 이미지를 분류하는 모델의 연구를 통해 데이터 분류의 시간을 단축하거나 머신러닝을 활용한 경관예측 인자분석을 통해 경관계획 요소의 중요도 분석 등의 주제에 맞는 연구 방법을 탐색하고 적용하여 후속 연구를 진행한다면 조경학 분야에서도 머신러닝 기법을 보다 유용하고 가치 있게 활용할 수 있을 것으로 생각된다.

• 한국유통학회지:유통연구
• /
• 제17권5호
• /
• pp.1-23
• /
• 2012

대기업과 중소기업의 갈등이 심화되고 있고 낙수효과 또한 제대로 작동하지 않고 있으며 사업조정제도의 실효성에 대한 논란이 이어지고 있는 가운데 중소기업의 사업영역을 보호하고 중소 대기업간 양극화를 해소하며 더불어 골목상권도 보호하기 위한 방안으로 도입된 것이 중소기업 적합업종 지정제도이다. 중소기업 적합업종의 추진현황은 제조업분야로 중소기업 적합업종 품목 중 234개 품목을 신청 접수 받아 실태조사 및 분석하여 조정협의체의 품목을 선정하였다. 서비스업분야에서의 적합업종 지정은 사회적 갈등이 있는 업종부터 지정할 계획인데, 중소기업 및 소상공인의 생업과 관련된 3개 대분류 서비스업종을 대상으로 우선 지정하고 추후 순차적으로 확대할 예정이다. 하지만 중소기업 적합업종 품목으로 선정될 경우에는 중소기업의 성장 동기가 저해될 우려가 있으며, 중소기업 적합업종 품목 지정은 소비자 후생 감소가 나타날 수 있다. 또한 사전적 규제로 작용할 소지가 높을 뿐만 아니라 경쟁을 제도적으로 제한함으로써 부작용이 나타날 우려가 있으며 FTA 체제의 주요 규정에 대한 위배 가능성도 있다. 뿐만아니라 대기업에 대한 역차별 요인이 충분히 반영되지 않고 있다는 점도 문제점으로 지적된다. 특히 중소기업 적합업종제도가 대기업의 주력분야와 관계없는 서비스업에 대한 진출 확대로 인해 중소기업 및 소상공인과의 갈등을 초래하고 있는 실정이므로 중소기업이나 중소상인의 보호를 위해서는 프랜차이즈시스템을 통해서 지역 중소기업을 발전시키고 마스터 프랜차이즈나 지역 프랜차이즈 시스템과 같은 선진 계약 방식을 도입하는 것이 필요하다. 하지만 이러한 방식은 기업들의 경쟁력과 운영방식을 한층 더 진일보 시켜 중소 프랜차이즈기업의 경쟁력 강화에 기여하는 효과도 있지만 부정적 측면이 더 많다고 볼 수 있다. 첫째, 지식경제부가 밝히고 있듯이, 프랜차이즈산업은 자영업자의 창업 성공률을 높여주고, 기존 자영업자를 조직화하여 규모의 경제를 통한 경쟁력 강화에 기여할 뿐만 아니라 다양한 서비스를 소비자에게 제공함으로써 내수시장을 확대하고, 일자리 창출에 기여하는 등 자영업자 경쟁력 제고와 서비스 산업 활성화를 위한 '유용한 수단'임을 강조하고 정부 서민안정 대책으로 밝힌바 있다. 이러한 관점에서 본다면, 프랜차이즈는 적합업종 제도의 취지에 부합하는 것이며 이에 반하는 것이 아님을 알 수 있다. 둘째, 적합업종으로 지정될 경우 국제적 경쟁력을 갖고 있는 국내 프랜차이즈 대기업들의 위축과 사기저하로 인하여 해외진출과 R&D, 식품안전에 대한 투자 감소와 더불어 국내 진출한 해외 기업들의 사업 확장에 부정적 영향을 끼칠 수 있다. 또한 국내 진출한 다국적 해외 프랜차이즈기업들과의 경쟁력을 확보하는 것이 무엇보다도 시급한 국내 프랜차이즈산업 현실에서 국제적 경쟁력 확보의 어려움뿐만 아니라 국내에 진출한 해외 프랜차이즈기업들과의 역차별이 발생할 수도 있다. 셋째, 중소기업 적합업종 품목 지정은 지금까지 제품을 사용해 왔던 소비자들의 선택의 기회를 제한함과 동시에 소비자의 후생을 감소시키는 부정적인 효과를 초래한다. 또한 중소기업 간의 역차별 문제를 발생시켜 소수 중소기업이 시장을 독점함으로써 소비자 선택의 폭이 줄어들 가능성이 있으므로 제품의 효용을 판단하는 역할은 국가가 아닌 소비자의 몫으로 남겨두어야 한다. 마지막으로는 프랜차이즈와 관련하여 이미 가맹사업법과 그리고 공정거래위원회의 모범거래기준 등의 시행으로 공정거래는 확보하고 있으므로 앞으로도 부족한 부분은 이들을 보완하여 진행하는 것이 바람직하다고 본다. 중소기업 적합업종 지정으로 이중삼중으로 규제하는 것은 오히려 프랜차이즈 분야에 과도한 제한이 될 것이다. 이제 국내 프랜차이즈산업에서도 한국의 문화를 전파하는 세계적 프랜차이즈기업이 성장할 수 있는 환경조성과 정부의 적극적인 지원이 필요하다. 따라서 프랜차이즈 기업의 성장 과정이나 배경을 고려하지 않고 현재 대기업이라는 이유만으로 이들에게 불이익을 주는 일은 없어야 한다. 프랜차이즈기업의 성장억제로 인하여 결국 가맹점의 매출감소는 물론이고 심지어는 폐업하는 가맹점의 숫자를 증가시키는 또 다른 문제를 발생시킬 수 있다는 것이다. 따라서 중소기업 적합업종제도가 대기업의 발목을 잡는 것이 아니라 소상공인과 중소기업의 경쟁력 제고와 동반성장을 목표로 하고 있는 만큼 대기업과 소상공인 및 중소기업이 상생과 협력을 바탕으로 거래관계를 지속하는 프랜차이즈 기업들이 포함되지 않도록 하는 것이 타당할 것이다.