• Earthquakes and Structures
• /
• 제11권6호
• /
• pp.943-966
• /
• 2016

Recently, magnetorheological elastomer (MRE) material and its devices have been developed and attracted a good deal of attention for their potentials in vibration control. Among them, a highly adaptive base isolator based on MRE was designed, fabricated and tested for real-time adaptive control of base isolated structures against a suite of earthquakes. To perfectly take advantage of this new device, an accurate and robust model should be built to characterize its nonlinearity and hysteresis for its application in structural control. This paper first proposes a novel hysteresis model, in which a nonlinear hyperbolic sine function spring is used to portray the strain stiffening phenomenon and a Voigt component is incorporated in parallel to describe the solid-material behaviours. Then the fruit fly optimization algorithm (FFOA) is employed for model parameter identification using testing data of shear force, displacement and velocity obtained from different loading conditions. The relationships between model parameters and applied current are also explored to obtain a current-dependent generalized model for the control application. Based on the proposed model of MRE base isolator, a second-order sliding mode controller is designed and applied to the device to provide a real-time feedback control of smart structures. The performance of the proposed technique is evaluated in simulation through utilizing a three-storey benchmark building model under four benchmark earthquake excitations. The results verify the effectiveness of the proposed current-dependent model and corresponding controller for semi-active control of MRE base isolator incorporated smart structures.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 전력전자학술대회
• /
• pp.429-430
• /
• 2011

This paper presents a simple and cost-effective stand-alone rapid battery charging system of 30kW for electric vehicles. The proposed system mainly consists of active front-end rectifier of neutral point clamped 3-level type and non-isolated bi-directional dc-dc converter of multi-phase interleaved half-bridge topology with coupled inductors. The charging system is designed to operate for both lithium-polymer and lithium-ion batteries. The complete charging sequence is made up of three sub-interval operating modes; pre-charging mode, constant-current mode, and constant-voltage mode. The pre-charging mode employs the staircase shaped current profile to accomplish shorter charging time while maintaining the reliable operation of the battery. The proposed system is able to reach the full-charge state within less than 16min for the battery capacity of 8kWh by supplying the charging current of 67A. The optimal discharging algorithm for Vehicle to the Grid (V2G) operation has been adopted to maintain the discharging current of 1C. Owing to the simple and compact power conversion scheme, the proposed solution has superior module-friendly mechanical structure which is absolutely required to realize flexible power expansion capability in a very high-current rapid charging system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.840-843
• /
• 1993

In this paper, an LPM controller using microprocessor was implemented and adopted Microstep method to control the LPW. In Microstep method, current waveform is sinusoidal not square. This method is characterized by less vibrating, less noisy, and more precise position control. Also, we simulate the static thrust characteristics for each waveform. The experiment was performed according to the mechanical vibration at the acceleration mode and slewing mode. The current tracks reference sinusoidal waveform well and stability was improved as we expected. Therefore, the possibility of the open loop position control was proposed.

• 한국전자파학회논문지
• /
• 제15권6호
• /
• pp.540-547
• /
• 2004

본 논문에서는 900 MHz대역에서 70 % 이상의 고효율을 갖는 전류 모드 D급 전력증폭기를 설계, 제작하였다. 푸시-풀 B급 전력증폭기의 구조를 기초로 하여 병렬 고조파 컨트롤 회로를 적용하여, 기존 D급 전력증폭기의 큰 손실 요인이었던 소자 내 커패시턴스의 충, 방전에 의한 전력 손실을 최소화하였다. 측정결과, 900 MHz 대역, 출력전력 3.2 W에서 73 % 전력 부가 효율, 그리고 출력전력 5 W에서 72 % 전력 부가 효율을 각각 얻었으며 DC 전력에 따라 출력의 크기가 선형적으로 변화하는 D급 전력증폭기의 특성을 확인하였다.

• 전기학회논문지
• /
• 제65권4호
• /
• pp.586-592
• /
• 2016

The current control of Continuous Conduction Mode(CCM) can be implemented by several methods: peak current control; average current control; and hysteresis control. Among these methods, the hysteresis current control is popularly applied in various converter applications because of its simplicity of implementation, fast current control response and inherent peak current limiting capability. However, a current controller with conventional hysteresis band which multiplies the current reference has the disadvantage that the modulation frequency varies in one cycle of the input voltage and, as a result, generates high switching frequency in the low input voltage section. Also it is complicated to design the input filter due to varying switching frequency. This paper proposed an optimum hysteresis-band current control method where the band is generated by using both multiplication method and sum method to maintain the modulation frequency to be nearly constant. This approach can solve the high switching frequency in the low input voltage section, and achieve easy design of input filter. The performance of the proposed converter is verified with the simulation and the experimental works.

• 전력전자학회논문지
• /
• 제21권4호
• /
• pp.364-372
• /
• 2016

In this paper, a voltage controller for the seamless transition of a grid-connected inverter for ESS is proposed. The single-phase inverter is operated as a current controller when the grid is connected and as a voltage controller in the stand-alone mode when the grid is disconnected. Generally, in the case of grid recovery, the overcurrent may flow into the system because of the mismatch phase between the inverter output and grid voltages. The proposed controller resolves the overcurrent problem through phase delay problems with initial value feed-forward control of the integrator when the grid voltage is restored. The effects of the control method are simulated through PSIM, and the usefulness of the control method is verified through experiments.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1569-1576
• /
• 2014

This paper mainly proposes a direct torque control strategy to minimize torque ripple in brushless DC (BLDC) motor. BLDC motor has large current and torque ripple when one voltage vector applied in one cycle due to its low inductance. Hence, this paper proposed a hysteresis torque control with PWM mode to control the resultant torque. Moreover, when the direct torque control system is operating during the two-phase half-bridge $120^{\circ}$ conduction mode, large torque ripple in commutation area appears every 120 electrical degree. Based on analyzing the root of torque ripple in detail, lookup tables of switching devices states for new half-bridge modulation mode in the positive and negative reference torque put forwarded. Finally, simulations by MATLAB software and experiment results from DSP are presented to verify the feasibility and effectiveness of the proposed strategy operating in four-quadrant operation.

• Current Research on Agriculture and Life Sciences
• /
• 제4권
• /
• pp.95-101
• /
• 1986

진동경운(振動耕耘)에 있어서 경운저항(耕耘抵抗) 및 동력(動力)을 최소(最小)로 하는 Computer에 의한 자동제어(自動制御) 시스템의 개발(開發)을 목적(目的)으로 3가지 Mode의 제어(制御) program을 작성(作成)하여 실험(實驗)과 Simulation을 통(通)하여 각 Mode의 제어성능(制御性能)을 조사(調査)하였다. 진동속도비(振動速度比)를 일정(一定)(1.5)하게 한 경우 3가지 Mode 모두 동일(同一) 진동조건(振動條件)에 수렴하였다. 그러나 흙의 전단주파수(剪斷周波數)에 Blade의 진동수(振動數)를 match 시키는 방법 즉 흙의 전단주파수(剪斷周波數)의 2배의 진동수(振動數)로 Blade를 진동(振動)시키는 제어(制御) Mode가 수렴 시간이 짧고, 견인저항 및 동력의 최적치(最適値)에 가장 가까웠다. 또 경심(耕深) 및 토양수분(土壤水分)의 변화(變化)와 같은 외란(外亂)에 대한 견인저항 감소율의 변동(變動)은 10%이하(以下)로 적었다. 이상(以上)과 같이 흙의 전단주파수(剪斷周波數)에 Blade의 진동수(振動數)를 match 시키는 제어(制御) Mode의 제어성능(制御性能)이 가장 우수함을 알았다.

• 한국정밀공학회지
• /
• 제24권5호
• /
• pp.56-61
• /
• 2007

In the braking of railway rolling stock, the slip that is the relative velocity between train body and its wheel affects the adhesive force which is connected to the braking force. The coefficient of the adhesive force changes in accordance with the slip and the condition of a rail road. Namely, its value increases upon the maximum on a rail condition, and there it declines conversely while the magnitude of slip keeps rising on. First, this paper introduced a reference slip generator so that can utilize maximum adhesive forces with a disturbance observer for estimating unmeasurable current adhesive forces which is as an input of the generator. And, an adaptive sliding-mode control system has been synthesized for minimizing the error between reference and current slip. Finally the effectiveness of the proposed control system is evaluated by computer simulation.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1614-1622
• /
• 2014

A novel equivalent flux sliding-mode observer (SMO) is proposed for dual three-phase interior permanent magnet synchronous motor (DT-IPMSM) drive system in this paper. The DT-IPMSM has two sets of Y-connected stator three-phase windings spatially shifted by 30 electrical degrees. In this method, the sensorless drive system employs a flux SMO with soft phase-locked loop method for rotor speed and position estimation, not only are low-pass filter and phase compensation module eliminated, but also estimation accuracy is improved. Meanwhile, to get the regulator parameters of current control, the inner current loop is realized using a decoupling and diagonal internal model control algorithm. Experiment results of 2MW-level DT-IPMSM drives system show that the proposed method has good dynamic and static performances.