• Advances in concrete construction
• /
• v.16 no.3
• /
• pp.169-176
• /
• 2023

The aim of the study was to establish the influence of particle size, chemical and phase composition of fine microspherical high-calcium fly ash (HCFA), as well as superplasticizer content on the strength of cementless composite materials based on 100% HCFA and mixtures of HCFA with Portland cement (PC). For the initial HCFA fractions, the particle size distribution, chemical and quantitative phase composition were determined. The compressive strength of cured composite materials obtained at W/B 0.4 and 0.25 was determined at a curing time of 3-300 days. For cementless materials, it was found that a change in the particle size d90 from 30 ㎛ (fraction 3) to 10 ㎛ (fraction 4) leads to an increase in compressive strength by more than 2 times. Compressive strength increases by at least another 2.2 times with the addition of Melflux 5581F superplasticizer (0.12%) and at W/B 0.25. The HCFA-PC blends were investigated in the range of 60-90% HCFA and the maximum compressive strength was found at 80% HCFA. On the basis of 80% HCFA-20% PC blend, the samples of ultra-high strength (108 and 150 MPa at 28 and 100 days of hardening) were obtained with the addition of 0.3% Melflux 5581F and 5% silica fume. The quantitative phase composition was determined for composite materials with a curing age of 28 days. It has been established that in a sample with ultra-high strength, a more complete transformation of the initial phases of both HCFA and PC occurs as compared to their transformation separately.

• Journal of the Korea Concrete Institute
• /
• v.19 no.1
• /
• pp.27-37
• /
• 2007

The purpose of this study is to propose a method to predict the minimum curing time of early age concrete required to prevent frost damage. Tests were performed to examine major factors, which affect the compressive strength of concrete frozen at early ages and investigate the source of frost damage at early age concrete. The results from the tests showed that the loss rate of compressive strength decreases as the beginning time of frost damage was delayed and water-cement ratio was lower. In addition, the test results also showed that concrete made with type III cement was less susceptible to frost damage than concrete made with ordinary Portland cement and frost damage occurred through the formation of ice lenses. When early age concrete is being damaged by frozen, a phase transition into ice of free water presented at the capillary pores of the concrete gives a reason for the decrease of compressive strength. Accordingly, the frost resistance of fresh concrete can be determined based on the saturation degree of the capillary pores. The method to predict the minimum curing time was suggested using the concept of critical saturation degree of the capillary pores.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.1
• /
• pp.102-109
• /
• 2003

The purpose of this study was to evaluate the linear polymerization shrinkage(%) and microhardness of composite resin(Z-100, 3M, USA) according to 2-step light curing method. Conventional light curing unit(Curing Light 2500, 3M USA) and 2-step light curing unit(Elipar Highlight, ESPE, Germany) were used as light source. The strain gauge method was used for determination of polymerization shrinkage(%). Samples were divided by 3 groups according to light curing methods (Group I : $450mW/cm^2$, 40sec, Group II : $650mW/cm^2$, 40sec, Group III : $150mW/cm^2$, 10sec & $650mW/cm^2$, 30sec). Preparations of acrylic molds were followed by filling and curing. Strain gauges attached to each sample were connected to a strainmeter. Measurements were recorded at each second for the total of 10 minutes including the periods of light application. And microhardness of each group after 24hours from light irradiation were measured. Obtained data were analyzed statistically using Ore-way ANOVA and/or Scheffe test. The results of the present study can be summarized as follows: 1. Composite resin in acrylic molds showed the initial expansion at the early phase of polymerization. This was followed by the contraction with the rapid increase in volume during the first 60 seconds and gradually diminished as curing process continued. 2. The lowest linear polymerization shrinkage(%) was found in group III followed by group I, II during the measuring periods. 3. Group III using 2-step curing method showed statistically significant reduction of linear polymerization shrinkage(%) compared with group I, II at 1 minute and 10 minutes from light irradiation(p<0.05). 4. The microhardness values of each group not revealed significant difference.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.3
• /
• pp.15-27
• /
• 1998

Several aspects of polymer dispersed liquid crystal(PDLC) film properties make them interesting for display application. Most versions of PDLC materials are able to modulate light without the use of polarizers, which offers advantages in optical throughput(brightness) and viewing angle compared to polarizer-based display. In this papers, we attemped to doe minimum of remaining liquid crystals at polymer network for the liquid crystal-polymer composite (LCPC) films. In results, best phase separation behaviors turned out liquid crystal/monomer/oligomer mixture system.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.118-121
• /
• 2001

The investigation of cure kinetics and morphology studies on DGEBA/PEI/Anhydride system were performed by differential scanning calorimetry and scanning electron microscopy. Autocatalystic kinetics model was applied by isothermal scan test. Ozawa method and Kissinger method was applied by temperature scan. Activation energy was 95kJ/mol for neat DGEBA/NMA, 120kJ/mol for DGEBA/PEI(10p.h.r.)/NMA. The generation of secondary phase of PEI was observed and its size was grown up by increasing contents of PEI.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10c
• /
• pp.87-92
• /
• 1998

The purpose of this study is to use paper sludge ash as a material in manufacturing high strength admixture. The reactivity of paper sludge ash as iteself is low for the crystallized non-reactive $SiO_2$, but when the $SiO_2$ was removed, the phase component is mainly composed of glass phase which could react with cement hydrates. In this study, we manufactured high strength admixture using separated paper sludge ash, and examined the strength of mortar, spun concrete with and without this high strength admixture in steam curing. The strength of spun concrete with high strength admixture including paper sludge ash was more higher than that of spun concrete without admixture. As a result, it was found that paper sludge ash could be used to a pozzolanic material in manufacturing high strength admixture.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.13 no.1
• /
• pp.93-104
• /
• 1995

Liquid crystal-polymer composite(LCPC) films promising new materials for both projection displays and vision product. LCPC films consist of a continous liquid crystal phase embedded in a three- dimensional network of polymer matrix. The liquid crystal in these LC phases can be elecrtrically switched giving rise to an opaque scattering off-stats and a transparent, non-scatting on- stats. In this work. a premixture is composed of LC, UV-curable monomer and photonitiator. LCPC films are formed by photopolymerization induced phase separation from this premixture. In conclusion, structure and electro-optical properties of LCPC films strongly depends on the selection of monomer, LC content and curing rate.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.13 no.2
• /
• pp.19-32
• /
• 1995

Liquid crystal-polymer composite(LCPC) films are promising new materials for both projection displays and vision products. LCPC films consist of a continuous liquid crystal phase embedded in a three- dimensional network of polymer matrix. The liquid crystal in these LC phases can be electrically switched giving rise to an opaque scattering off-state and a transparent, non- scattering on-state. In this work, a premixture is composed of LC, UV-curable monomer and photonitiator. LCPC films are formed by photopolymerization induced phase separation from this premixture. In conclusion, structure and electro-optical properties of LCPC films strongly depends on the selection of monomer, LC content and curing rate.

• Journal of the Korean Ceramic Society
• /
• v.36 no.12
• /
• pp.1342-1349
• /
• 1999

In order to improve the density and the mechanical strength without change in chemical composition the hardened pastes of hydroxyapatite cement were reinforced with powders and/or whiskers of hydroxyapatite. The powders behaved as a seed of hydroxyapatite formation rather than a filler while the whiskers were mrerly dispersed in matrix and capillary pores of the hardened bodies leading to increase in mechanical strength. But the increase in strength But the increase in strength was nnt enough owing to the lack of homogeneous dispersion of the fibers. The highest diametral tensile strength of 18.5 MPa was measured at the hardened hydroxyapatite body in which well-dispersed whisker phase formed uniformly during hydro-thermal curing of power-added and dry-formed hydroxyapatite cement.

• Elastomers and Composites
• /
• v.54 no.3
• /
• pp.188-200
• /
• 2019

Rubber articles contain various organic additives such as antidegradants, curing agents, and processing aids. It is important to extract and analyze these organic additives. In this paper, various extraction methods of organic additives present in rubber composites were introduced (solvent extraction, Soxhlet extraction, headspace extraction, and solid-phase microextraction), and the extracts were characterized using gas chromatography/mass spectrometry (GC/MS). Solvent and Soxhlet extractions are easy-to-perform and commonly used methods. Efficiency of solvent extraction varies according to the type of solvent used and the extraction conditions. Soxhlet extraction requires a large volume of solvent. Headspace sampling is suitable for extracting volatile organic compounds, while solid-phase extraction is suitable for extracting specific chemicals. GC/MS is generally used for characterizing the extract of a rubber composite because most components of the extract are volatile and have low molecular weights. Identification methods of chemical structures of the components separated by GC column were also introduced.