• Journal of the Korea Concrete Institute
• /
• v.20 no.6
• /
• pp.721-729
• /
• 2008

The purpose of this study is to investigate the engineering properties of concrete for the early strength development. As a result of reviewing it by establishing each experimental factor and level, the cement had more excellent quality performance in CHC and HESPC than OPC. This study has shown that the PC series admixture was more excellent in side of elapsed time (aging) and early strength development than PNS series admixture. In addition, there was much difference according to the curing temperature, but the early strength development showed the considerable vulnerability in curing temperature below $12^{\circ}C$. To satisfy the strength requirements of 5 MPa/18 hr this study has shown that it needed the curing temperature over $17^{\circ}C$ to the minimum in OPC, over $14^{\circ}C$ in CHC, and over $11^{\circ}C$ in HESPC. On the other hand, as to the strength properties according to W/C, the less W/C was, the more strength development was excellent. If this study is to be used in construction filed on a basis of this result, this researcher is considered as possible of the economic execution of construction by advancing the early strength and by the reduction of construction cost according to shortening construction duration.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.766-771
• /
• 2016

This study examined the long-term durability of PC boxes, which was manufactured by low-carbon eco-friendly concrete using an alternative binder to cement and alternative fine aggregate to sand and microwave heat curing system to reduce the construction cost of a near-surface transit system. Based on the test results, the initial compressive strength of microwave heat cured concrete was higher than that of the steam cured concrete, but those were similar in the long-term age. In addition, there was no significant difference between the two curing conditions in the chemical resistance and the freeze-thawing resistance, and the chloride ion penetration level of the concrete cured by two methods was very low. Therefore, low-carbon eco-friendly concrete and microwave heat curing technology are expected to contribute to the economic construction of a near-surface transit system, and reduce carbon dioxide emissions and environmental impact.

• The Journal of Korean Medicine
• /
• v.21 no.3
• /
• pp.31-39
• /
• 2000

Objectives : Chekamuiyiin-tang has effects of promoting diuresis, promoting blood circulation, elimating phlegm and strengthening the body's resistance to disease. We experimented with Chekamuiyiin-tang in order to find effects which might possibly cure obesity. Methods : We fed a control group of rats a high fat diet and administered normal saline for 8 weeks. And we fed an experimental group of rats a high fat diet and administered an extract of Chekamuiyiin-tang for 8weeks. Results : The serum total cholesterol level, triglyceride level, free fatty acid level, total lipid level and phospholipid level in the Chekamuiyiin-tang group showed a significant decrease in comparison with the control group. The serum HDL-cholesterol level in the Chekamuiyiin-tang group showed no change in comparison with the control group. The serum LDL-cholesterol level in the Chekamuiyiin-tang group showed a decrease in comparison with the control group, but this result showed no efficacy. The size of the epididymal fat cell and the fat drops area in the hepatic lobule of rats in the Chekamuiyiin-tang group showed a significant decrease in comparison with the control group. Conclusios : According to the above results, Chekamuiyiin-tang has shown to be capable of curing and preventing obesity.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.2
• /
• pp.67-73
• /
• 2011

Ion exchange resins can be one of the good carriers for sustained drug release. However, the sustained release may not be enough only with themselves and hence film coating with rate controlling polymers can be applied to have a further effect on the drug release. Due to the environmental and economic issues of organic solvent for the polymer coating, aqueous polymeric systems were selected to develop dosage forms. Among the many aqueous polymeric dispersions for the film coating, EC (ethylcellulose) based polymers such as Aquacoat$^{(R)}$ ECD and Surelease$^{(R)}$ were evaluated.A fluid-bed coating was applied as a processing method. The drug release rate was quite dependent on the coating level so the release rate could be modified easily by changing different levels of the coating. The drug release rate in the Aquacoat$^{(R)}$ coated resin particles was strongly dependent on curing, which is a thermal treatment to make homogeneous films and circumvent drug release changes during storage. After dissolution test using the compressed tablets in which the coated resin particles are contained, inhomogeneous coating and even pores could be observed showing that the mechanical properties of EC were not resistant to granulation and compaction process. However, when tablets were prepared in different batches, the release profiles were almost identical showing the feasibility of the coated resin particle as incorporated into the tablet formulation.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.76-81
• /
• 2016

Recycled aggregate is a valuable resource in Korea in lack of natural aggregate. Government recognizes the importance and suggests various policies enhancing its use for higher value-added application. Most of recycled aggregate produced currently in Korea, however, is applied for low value-added uses such as embankment, reclamation, etc. Its higher valued application such as for structural concrete is very limited. Although domestic manufacturing technology of recycled aggregate is at the world level, recycled aggregate is not applied for structural concrete. Primary reasons for the limited use of the recycled aggregate include bonded mortar and cracks occurred during crushing and hence it is very difficult to predict and control the quality of recycled aggregate concrete. This research intended to grasp combined characteristics of recycled aggregate, high early strength cement, maximum temperature and time duration of steam curing and then, analyze the effects of factors. Also, it suggested the method to improve field applicability of recycled aggregate concrete.

• The Journal of Korean Medicine
• /
• v.21 no.1
• /
• pp.3-10
• /
• 2000

We experimented with several prescriptions in order to find cure and prevention effects for obesity. We fed control group rats a high fat diet and adiministered normal saline for 8weeks. We fed experimental group rats a high fat diet and administered extract of four prescriptions for 8weeks. The results were as follows; 1. The serum total cholesterol level in Bikam-whan and Chekamhanghyuluiyiin-tang group showed a significant decrease in comparison with Control group. 2. The serum triglyceride level in Bikam-whan, Chekamhanghyuluiyiin-tang and Chekambangpungtongseong-san group showed a significant decrease in comparison with Control group. 3. The serum free fatty acid level in Chekamhanghyuluiyiin-tang and Chekambohyulansin-tang group showed a significant decrease in comparison with Control group. 4. The serum total lipid level in Bikam-whan, Chekamhanghyuluiyiin-tang and Chekambohyulansin-tang group showed a significant decrease in comparison with Control group. 5. The serum phospholipid level in Bikam-whan and Chekamhanghyuluiyiin-tang group showed a significant decrease in comparison with Control group. 6. The serum glucose level in Bikam-whan and Chekamhanghyuluiyiin-tang group showed a significant decrease in comparison with Control group. According to the above results, Bikam-whan and Chekamhanghyuluiyiin-tang has shown to be capable of curing and preventing obesty.

• Korean Journal of Agricultural Science
• /
• v.45 no.3
• /
• pp.475-484
• /
• 2018

Nitrite is an essential additive for the manufacture of cured meat products. This study was conducted to investigate the curing effect of the plasma treated juice of red Perilla in meat batter. The nitrite content in the juice of red Perilla was increased by the indirect treatment of atmospheric pressure plasma, and the lyophilized powder of red Perilla juice contained 9,133 ppm of nitrite. A meat batter without a nitrite source was prepared as a negative control (NC), and the meat batters cured with sodium nitrite (PC), celery powder (CP), and the lyophilized powder of red Perilla juice treated with atmospheric pressure plasma (PTP) at 70 ppm level of nitrite were prepared. The PTP showed the highest pH and the lowest cooking loss among the treatments. There were no significant differences in the nitrosyl-hemochrome content in the cooked meat batters of the PC, CP and PTC. However, the PTP had a lower CIE $a^*$-value compared to the PC and CP. The malondialdehyde content in the cooked meat batters was significantly lower in the CP and PTP than in the NC while there was no significant difference between the NC and PC. Based on the results of this study, the plasma treated juice of red Perilla can be used as a new natural nitrite source for cured meat products.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.445-450
• /
• 2001

The paper investigates the relationships between dynamic elastic modulus and static elastic modulus or compressive strength according to curing temperature, aging, and cement type. Based on this investigation, the new model equations are proposed. Impact echo method estimates the resonant frequency of specimens and uniaxial compression test measures the static elastic modulus and compressive strength. Type I and V cement concretes, which have the water-cement ratios of 0.40 and 0.50, are cured under the isothermal curing temperature of 10, 23, and 50 $^{\circ}C$. Cement type and aging have no large influence on the relationship between dynamic and static elastic modulus, but the ratio of dynamic and static elastic modulus comes close to 1 as temperature increases. Initial chord elastic modulus, which is calculated at lower strain level of stress-strain curve, has the similar value to dynamic elastic modulus. The relationship between dynamic elastic modulus and compressive strength has the same tendency as the relationship between dynamic and static elastic modulus. The proposed relationship equations between dynamic elastic modulus and static elastic modulus or compressive strength properly estimates the variation of relationships according to cement type, temperature, and aging.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.754-761
• /
• 2008

In general, stress measurement of existent shotcrete lining be used by pressure cells. but, measuring instrument is lost by high pressure at shotcrete lining construction and pressure cell's measurement value have to low believability by natural conditions like curing temperature. In this study, proposed techniques to measure without utilizing sensitive stress sensor in natural condition at point that want stress of shotcrete lining after shotcrete lining construction. Executed numerical analysis to forecast stress level that interact in tunnel shotcrete lining, measured strain of hole by load action through hole in shotcrete lining. 3D FEM(finite element method) is enforced through various parameters curing time of shotcrete lining, thickness, load condition. Different model cases applied by parametic study. As analysis result, it could grasp development possibility of method that propose this time because it could examine corelation with strain by near hole of shotcrete lining and stress about load condition.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.4
• /
• pp.816-822
• /
• 1996

The purpose of this study was to determine whether there was any difference in the mean porosity of denture base resin cured by microwave energy, when the liquid monomers of denture resin(K-33 : methyl methacrylate for conventional water bath curing or Acron MC : special monomer for microwave curing) and/or the thicknesses of denture base($5{\times}10{\times}60mm\;or\;10{\times}10{\times}60mm$) were varied. The mean porosities of k-33 specimens cured in water bath with two different thicknesses were used as control. The results were as follows : 1. Regardless of specimen thickness, Acron MC cured by microwave energy showed the least mean porosity, followed by K-33 cured by water bath heat, and K-33 cured by microwave energy showed the highest level of mean porosity(P<0.05). 2. In both K-33 and Acron MC cured by microwave energy the mean porosities of 5mm thickness groups were lower than those of 10mm thickness groups(P<0.05). But no significant difference was found in mean porosity between 5mm thickness and 10mm thickness of water bath heat cured groups made of K-33(P>0.05).