• Polymer(Korea)
• /
• v.27 no.2
• /
• pp.120-128
• /
• 2003

The effects of catalyst, accelerator and blend composition on the cure behavior of unsaturated polyester resin (UPE), vinyl ester resin (VE) and their blends were studied using differential scanning calorimetry(DSC). The DSC thermograms strongly depend on each variable. The result shows that the small exothermic peak at 115$^{\circ}C$ is due mainly to the UPE component in the UPE/VE blends and the large one at 134~138 $^{\circ}C$ is due mainly to the VE component. The results also indicate that the change of the DSC thermogram measured after each blend was exposed to high temperature 18$0^{\circ}C$ and the fast curing conditions of a few tens seconds provide useful information on understanding the thermal processing of a blend at high speed. The measurements of resin flow time represent that there are three distinct stages of cure in the UPE/VE blends: induction, transition and macro-gelation stages, as similarly reported for UPE by others earlier. The thermal stability and flexural properties of the cured UPE are significantly improved by blending it with the VE, depending on the composition.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.42-50
• /
• 2004

In this work, the diglycidylether of bisphenol A (DGEBA) and modified polyurethane (PU) blends were initiated by N-benzylpyrazinium hexafluoroantimonate (BPH). The cure and fracture toughness of neat DGEBA with the addition of PU were investigated. The cure properties of DGEBA/PU blend system were examined by DSC and near-IR measurements. The fracture touhtness were investigated by measuring the critical stress intensity factor ($K_{IC}$) and the critical strain energy release rate ($G_{IC}$). According to the results, the maximum values of owe activation energy ($E_a$) and conversion (${\alpha}$) were found at 10 phr of PU. Also the $K_{IC}$ showed a similar behavior with the results of conversion. These results were probably due to increase of crosslinking density in the blends resulted from increase of the hydrogen bonding between the hydroxyl groups of DGEBA and isocyanate groups of PU.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.133-140
• /
• 2013

Carbon fiber reinforced polymer (CFRP) composites consist of carbon fibers in a polymer matrix. Recently, CFRP composites having high thermal stability and low outgassing are finding their use in high performance materials for aerospace and electronics applications under high temperature and high vacuum conditions. Cyanate ester resin is one of the most suitable matrix resins for this purpose. In this study, proper combination of cyanate ester and catalyst, curing behavior, and cure cycle were determined by chemorheology. Optimum condition was found to be catalyst content of 100 ppm and curing temperature of $150^{\circ}C$. Thermal stability and outgassing of cured resin composition were analyzed and the results showed thermal decomposition temperature of $385^{\circ}C$ and total mass loss of 0.29%. The CFRP prepregs and subsequent composites were fabricated by predetermined resin composition and the cure condition. Tensile moduli of the composites were compared with theoretical models and the results were very consistent.

• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.356-361
• /
• 1996

Cure kinetics of diglycidyl ether of bisphenol A(DGEBA)/4,4'-methylene dianiline(MDA) with hydroquinone-phenyl glycidyl ether(HQ-PGE) as a reactive additive, which was preliminarily synthesized, was investigated by DSC and FT-IR analyses. Kissinger equation and Arrhenius' equation were used to calculate activation energy and pre-exponential factor. When HQ-PGE was added to DGEBA/MDA system, it reduced activation energy of system. When the 5 phr of HQ-PGE was added to DGEBA/MDA system, activation energy was 7.8 kcal/mol by FT-IR analysis and 11.3 kcal/mol by DSC, in comparison with the system without HQ-PGE, activation energy decreased about 30% and 9%, respectively. According to these results, HQ-PGE, introducing agent of this system, acted as a catalyst.

• Composites Research
• /
• v.15 no.2
• /
• pp.40-47
• /
• 2002

The di-functional epoxy resins, i.e., diglycidylether of bisphenol A(DGEBA) and diglycidylethere of bisphenol F(DGEBF) were initiated by cationic catalyst, i.e., benzylquinoxalinium hexafluoroantimonate(BQH) using electron-beam(EB) technique. And the effect of structure of DGEBA and DGEBF on thermal stabilities and cure behaviors was investigated. According to the experimental results, the decomposed activation energy based on Horowitz-Metzger method was higher in the case of DGEBA, but intergral procedural decomposition temperature(IPDT) of DGEBA was lower than DGEBF. This could be interpreted in terms of high crosslink density resulted from hydroxyl bond of DGEBF backbone. It was confirmed in increasing the hydroxyl band at $7000\;cm^{-1}$ and $5235\;cm^{-1}$ using near-infrared spectroscopy(NIRS).

• Applied Chemistry for Engineering
• /
• v.5 no.6
• /
• pp.967-974
• /
• 1994

We studied the cure kinetics of the DGEBA(Diglycidyl ether of bisphenol A)/MDA(4, 4' -methylene dianiline)/MN(Malononitrile)/HQ(Hydroquinone) system by Barrett method and Integral method with dynamic runs of differential scanning calorimetry(DSC). Kinetic parameters such as activation energy and pre-exponential factor were obtained and reaction order was estimated roughly supposing that present system was adjusted to nth order reaction. The MN(Malononitrile) was introduced as a chain extender and HQ(Hydroquinone) as a reactive accelerator or catalyst.

• Elastomers and Composites
• /
• v.29 no.1
• /
• pp.18-29
• /
• 1994

The purpose of this study is to investigate reinforced effect between silica treated by coupling agents and rubber matrix under the configuration chemical bonds, and the effect of silica particles coated by organic polymers using aluminum chloride as the catalyst. In vulcanization characteristies were tested by Curastometer. The M-series vulcanizates were reached to the fastest optimum cure $time(t_{90})$ and R-series vulcanizates with the same formula had the shorted optimum cure times. Tensile characteristics measuring with a tensile tester revealed that the M-series vulcanizate was the best in the physical properties, such as tensile strength. In 100% modulus, however, the S-series vulcanizates appeared to be better than the other vulcanizates. Also, hardness showed the following order : S-series>R-series>M-series with the order of elongation R-series>M-series>S-series. In SEM test, shapes of chemical treated silicas were observed. The dispersion of filler in the SBR composite appeard uniformly. In RDS test for the dynamic characteristics, G' indicates that S-3 shows the highest value with the next order M-3>R-3, and the order of damping values are as followe: M-3>M-3>R-3.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.960-966
• /
• 1997

The effects of epoxy resins and content of catalyst on the cure characteristics were studied by FT-IR, DSC and dynamic viscometer for the thermal properties and rheological properties of the catalytic (N-Benzylpyrazinium hexafluoroantimonate, BPH) epoxy thermosetting system. Compared with DSC results of DEGBF containing 0.5wt% BPH, the DSC thermograms of DGEBA containing 0.5wt% BPH indicated that the reaction was faster than that of DGEBF/BPH and the conversion rate of DGEBA/BPH was high in the initial stage of the reaction. As the concentration of BPH increases, the reaction and conversion rates show similar value in both the cases. The influence of hydroxyl group of epoxy resin on gel point defined from the crossover point of storage modulus (G') and loss modulus (G") could be explained by the formation of 3-dimensional network in the initial stage owing to the curing reaction between epoxides and hydroxyl groups of epoxy resin. This was consistent with the gel point obtained from DSC, FT-IR and moduli crossover. The activation energy (Et) obtained from the crossover point (G'/G"=1) are $31-39kJ.mol^{-1}$ for various BPH compositions in case of two epoxy systems.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.221-226
• /
• 2008

Novel synthetic routes were proposed for hydroxy-terminated Poly(EO-co-THF) by Cationic ring-opening copolymerization of Tetrahydrofuran(THF) and Ethylene oxide(EO). It was carried out using Boron trfluoride tetrahydrofuranate($BF_3$ THF complex) as catalyst in the presence of 1,4-butandiol. The resultant products are well-defined linear polyetherpolyol. Polyurethane(TPU) were prepared using resultant polyetherpolyol with IPDI/N-100 as curing agent and TPB(Triphenylbismuth) /MA(Maleic anhydride) mixture as cure catalyst. Mechanical properties of TPU prepared from poly(EO-co-THF) polyol were investigated and compared with polyurethane using ATK HTPE.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.80-87
• /
• 2002

A comparative study using electron-beam(EB) and thermal curing techniques was carried out to determine the effect of cure behavior and thermal stability of epoxy resins. In this work, benzylquinoxalinium hexafluoroantimonate(BQH) was used as a latent cationic catalyst for an epoxy resin. According to the thermogravimetric analysis(TGA), the decomposed activation energy based on Coats-Redfern method was higher in the case of thermal curing technique. This could be interpreted in terms of slow thermal diffusion rate resulted from high crosslink density of the thermally cured epoxy resin. However, the increase of hydroxyl group in the epoxy resin cured by EB technique was observed in near-infrared spectroscopy(NIRS) measurements, resulting in improving the stable short aromatic chain structure, integral procedural decomposition temperature, and finally ductile properties for high impact strengths.