• Journal of Powder Materials
• /
• v.12 no.1
• /
• pp.51-55
• /
• 2005

$Cu_2O$ nano cubes with high catalase activity were synthesized by reduction of freshly prepared Cu in distilled water at $40^{\circC}$ and their catalase activities of $H_2O_2$ were studied. Transmission electron microscopy (TEM) observation showed that most of these nanocubes were uniform in size, with the average edge length of 30 nm. Selected area electron diffraction of TEM revealed that the nanocube consisted of single crystalline $Cu_2O$, but it changed to CuO phase. The catalase activity depends on the amount of both cuprite phase and surface area.

• Korean Journal of Heritage: History & Science
• /
• v.48 no.4
• /
• pp.4-23
• /
• 2015

Buried bronze objects are naturally corroded by their surrounding environment, which results in producing corrosion layers containing a number of constituents. Corrosion layers in stable condition protect the objects from the environment and also could provide information in terms of the objects. Characteristic and mechanism of the corrosion layers is likely to be valuable information for the conservation treatment. Many research have been conducted to figure out the formation and characteristic of the corrosion layers, but the more research should be conducted with various approach and analytical methods. Raman spectroscopy is one of the analytical methods to identify microcrystal as a compound while other analytical methods are used to identify element. Therefore, the aim of this research is to identify the characteristic of corrosion layers of both excavated bronze objects through the raman spectroscopy. Two analytical methods, which are raman spectroscopy and SEM~EDS, were used to analyse four excavated bronze bowls. In the case of bronze bowls, malachite was found from the exterior corrosion layer and albite, quartz, and microcline, which are minerals, were also found. Cuprite was detected from the interior corrosion layers illustrating slightly different spectrum due to the combined compound. Lead segregation shows the form of PbO, $PbSO_4$ and $PbCO_3$ or it replaced as cuprite. In this study, small number of samples were analysed. This research is likely to be useful information to figure out not only the characteristic of the corrosion layers but also the authenticity of the artifacts if relevant research will be conducted. Therefore, further comprehensive researches on the various archaeological objects and corrosion environment condition are required in the future.

• Korean Journal of Remote Sensing
• /
• v.28 no.4
• /
• pp.347-355
• /
• 2012

A fast algorithm for endmember extraction is proposed in this study which extracts min. and max. pixels from each band after MNF transform as candidate pixels for endmember. This method finds endmembers not from the entire image pixels but only from the previously extracted candidate pixels. The experimental results by N-FINDR using a simulated hyperspectral image data and AVIRIS Cuprite image data showed that the proposed fast algorithm extracts the same endmembers with the conventional methods. More studies on the effect of noise and more adaptive criteria in extracting candidate pixels are expected to increase the usability of this method for more fast and efficient analysis of hyperspectral image data.

• Journal of the Korean Ceramic Society
• /
• v.43 no.9 s.292
• /
• pp.544-551
• /
• 2006

The sealing technique between a glass tube and a copper heat pipe in an evacuated tube solar collector is studied. In this study two different sealing techniques, such as flame method and furnace firing, are examined. After the sealing of a copper to a glass, the oxidation state of the copper and its bonding morphology were examined by SEM and XRD. Its oxidation was retarded by coating of borate solution on the copper, and $Cu_2O(cuprite)$ turned into CuO(tenorite) with increase in a firing temperature and firing time. Porous structure was found in the oxide layer when CuO formed. The best sealing morphology was observed when the thickness of the oxidation layer was less than $20{\mu}m$. The sealing technique performed in a furnace was promising and the satisfactory result was obtained when the sample was fired at $950^{\circ}C$ for 5 min under $N_2$ atmosphere. Annealing procedure is recommended to remove the stress left at the bonding zone.

• Conservation Science in Museum
• /
• v.8
• /
• pp.49-69
• /
• 2007

This is about the scientific analysis of the 10 items of the gilt-bronze Panbul excavated from Anapji, Gyeongju. First, the composition of the Panbul was confirmed, using X-ray fluorescence spectrometer (XRF), and the patinas covering the surface of the Panbul were analyzed, using X-ray diffractometer (XRD). And the micro structures and gilt layer of the Panbul were investigated, using microscope and scanning electron microscope with energy dispersive spectrometer (SEM/EDS), and in order to investigate the internal conditions of the Panbul, X-radiography was conducted. As the result, it is found out that the material of the Panbul excavated from Anapji was the bronze of copper (86~95%) and tin (4~12%), and coated with gold. And cuprite (Cu₂O) was detected from red patina of the gilt-bronze Panbul, and chalcocite(Cu₂S) also was detected from the black patina. As the result of the observation of the micro structure through microscope, it is estimated that it was manufactured, using the wax molding method, and, judging from the fact that the thickness of gilt layer was not even, and that the groove had been filled, it was presumed that the amalgam coating method had been used, but some questions still remain, because mercury was not detected. Lastly, through the X-radiography, it was observed that the tiny round spots existed, which was presumed to have been generated during the casting.

• Journal of the Mineralogical Society of Korea
• /
• v.27 no.4
• /
• pp.183-195
• /
• 2014

In order to study the mineralogical characteristics of a cathodic deposition-metallic powder, electrowinning experiments were carrier out on different electrolytic solutions at varying electric distances and electric currents. Under the same experimental conditions, Cu recovery was obtained much more effectively using a sodium chloride electrolyte than with a sulfuric acid electrolyte. In XRD analysis, copper ($Cu^0$), chalcanthite and cuprite were identified in the sulfuric acid electrolyte, while copper, nantokite and chalcanthite were observed in the sodium chloride electrolyte. In the sodium chloride electrolyte solution, increasing the electric distance and the electric current increased the Cu recovery rate, anode weight and anodic corrosion. The results of XRD analysis with non-pulverized cathodic deposition-metallic powder showed the average copper crystallite size was increased by increasing the electric current and decreasing the electric distance. It is suggested that the mass transfer was controlled with diffusion on the boundary between the electrode and the electrolytic solution due to the formation of dendrite copper.

• Journal of the Mineralogical Society of Korea
• /
• v.31 no.1
• /
• pp.33-46
• /
• 2018

Traditional inorganic pigments applied to dancheong, buddhist painting, and wall painting were produced from natural minerals which were later replaced by synthetic pigments, resulting in the loss of the recipe to prepare mineral pigments. This study examined the domestic occurrence and mineralogical characteristics of green and blue mineral pigments required for the conservation of cultural heritage. Cuprous green-blue mineral pigments were found as the weathering products of waste dumps and ores of abandoned Cu-Pb-Zn sulfide mines. Mineralogical analyses using X-ray diffraction and scanning electron microscopy identified diverse hydrous copper sulfate pigments of green (brochantite and devilline) and blue color (linarite, bechererite, and schulenbergite) with minor green pigments of antlerite and atacamite commonly associated with cerussite, smithsonite, anglesite, and cuprite. Noerok, a green silicate pigment, replaced the fractured basalt lava. Celadonite was responsible for the green color of Noerok, closely associated with opal in varying ratio. Glauconite, green silicate pigment, was identified in the Yellow Sea sediments. Malachite and azurite, the most important green and blue pigments of Korean cultural heritage, were not identified in this study.

• Corrosion Science and Technology
• /
• v.7 no.2
• /
• pp.99-111
• /
• 2008

Copper was exposed unsheltered and sheltered in four humid tropical sites, representing urban, urban-industrial, urban-marine and rural environments. The corrosion rates and the sequence of corrosion product formation are presented and discussed in relation with climatic and atmospheric pollution parameters. Chemical compositions of corrosion products were found to depend on environments and duration of exposure. In all environments, cuprite was the predominating corrosion product that formed first and continuously increased during the exposure. Among the sulphur-containing corrosion products, posnjakite and brochantite were more frequently found and the first formed earlier. Nantokite was the most common chlorine-containing products for most cases, except the high-chloride environment, where atacamite was detected instead. The corrosion rate of copper was well indicated by the colour of patina. The red-purple colour corresponded to the high corrosion rate and the greenish grey colour corresponded to the low corrosion rate. Corrosion rate of sheltered copper in urban-marine environment increased with the exposure time.

• Journal of Conservation Science
• /
• v.35 no.4
• /
• pp.373-383
• /
• 2019

We characterized the smelting process and smelting furnace through scanning electron microscopy-energy dispersive spectroscopy, wavelength dispersive X-ray fluorescence, X-ray diffraction, and raman micro-spectroscopy with 13 relics including slags and furnace walls excavated from square-shaped building sites and pits of the Three Kingdoms site at the Ungyo site section I. Our results revealed that the principal components were FeO and SiO₂; and CuO, PbO, and ZnO were contained in small quantities. Furthermore, fayalite, magnetite, augite, copper, and cuprite were found. High contents of FeO or SiO₂ components seem to have been added to form fayalite to remove gangue in the smelting process. The relatively low content of S detected in the copper prills suggests that roasting was performed well. Cristobalite and mullite, which are minerals that indicate high-temperature found in the furnace wall, show that the smelting temperature was higher than 1,250℃. The findings of this study show a high possibility that the Wanju Ungyo site is smelting remains of copper ores, which are nonferrous metals, rather than iron. Various smelting byproducts excavated in this area in the future will help us better understand the copper smelting process that may have been performed since ancient times.

• ETRI Journal
• /
• v.35 no.6
• /
• pp.1156-1159
• /
• 2013

We investigate the characteristics of $Cu_2O$ thin films deposited through the addition of $N_2$ gas. The addition of $N_2$ gas has remarkable effects on the phase changes, resulting in improved electrical and optical properties. An intermediate phase ($6CuO{\cdot}Cu_2O$) appears at a $N_2$ flow rate of 1 sccm, and a $Cu_2O$ (200) phase is then preferentially grown at a higher feeding amount of $N_2$. The optical and electrical properties of $Cu_2O$ thin films are improved with a sufficient $N_2$ flow rate of more than 15 sccm, as confirmed through various analyses. Under this condition, a high bandgap energy of 2.58 eV and a conductivity of $1.5{\times}10^{-2}$ S/cm are obtained. These high-quality $Cu_2O$ thin films are expected to be applied to $Cu_2O$-based heterojunction solar cells and optical functional films.