• Asian Journal of Atmospheric Environment
• /
• v.11 no.3
• /
• pp.153-164
• /
• 2017

Odor dispersion around a cubic building from rooftop odor emissions was investigated using computational fluid dynamics (CFD). The Shear Stress Transport (here after SST) $k-{\omega}$ model in FLUENT CFD code was used to simulate the flow and odor dispersion around a cubic building. The CFD simulations were performed for three different configurations of cubic buildings comprised of one building, two buildings or three buildings. Five test emission rates were assumed as 1000 OU/s, 2000 OU/s, 3000 OU/s, 4000 OU/s and 5000 OU/s, respectively. Experimental data from wind tunnels obtained by previous studies are used to validate the numerical result of an isolated cubic building. The simulated flow and concentration results of neutral stability condition were compared with the wind tunnel experiments. The profile of streamline velocity and concentration simulation results show a reasonable level of agreement with wind tunnel data. In case of a two-building configuration, the result of emission rate 1000 OU/s illustrates the same plume behavior as a one-building configuration. However, the plume tends to the cover rooftop surface and windward facet of a downstream building as the emission rate increases. In case of a three-building configuration, low emission rates (<4000 OU/s) form a similar plume zone to that of a two-building configuration. However, the addition of a third building, with an emission rate of 5000 OU/s, creates a much greater odorous plume zone on the surface of second building in comparison with a two-building configuration.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.162-166
• /
• 2007

In the present study, the pressure coefficient of a cubic building model is numerically simulated. Three turbulence models of standard ${\kappa}-{\varepsilon}$, RNG ${\kappa}-{\varepsilon}$ and LES are adopted and the results are compared with the available experimental data. From the results, it has been found that RNG ${\kappa}-{\varepsilon}$ turbulence model and LES turbulence model were shown to predict fairly well the experimental pressure coefficient. In contrast, the results of the standard ${\kappa}-{\varepsilon}$ turbulence model showed large discrepancies in pressure coefficient on the side and top surfaces of the cubic building, which limits the applicability of the standard ${\kappa}-{\varepsilon}$ turbulence model on wind engineering.

• Carbon letters
• /
• v.16 no.3
• /
• pp.192-197
• /
• 2015

In the present work, we propose a molecule (C₁₄H₁₄) that can be used as a building block of hexagonal diamond-type crystals and nanocrystals, including wurtzite structures. This molecule and its combined blocks are similar to diamondoid molecules that are used as building blocks of cubic diamond crystals and nanocrystals. The hexagonal part of this molecule is included in the C₁₂ central part of this molecule. This part can be repeated to increase the ratio of hexagonal to cubic diamond and other structures. The calculated energy gap of these molecules (called hereafter wurtzoids) shows the expected trend of gaps that are less than that of cubic diamondoid structures. The calculated binding energy per atom shows that wurtzoids are tighter structures than diamondoids. Distribution of angles and bonds manifest the main differences between hexagonal and cubic diamond-type structures. Charge transfer, infrared, nuclear magnetic resonance and ultraviolet-visible spectra are investigated to identify the main spectroscopic differences between hexagonal and cubic structures at the molecular and nanoscale. Natural bond orbital population analysis shows that the bonding of the present wurtzoids and diamondoids differs from ideal sp³ bonding. The bonding for carbon valence orbitals is in the range (2s^0.982p^3.213p^0.02)-(2s^0.942p^3.313p^0.02) for wurtzoid and (2s^0.932p^3.293p^0.01)-(2s^0.992p^3.443p^0.01) for diamantane.

• Korean Institute of Interior Design Journal
• /
• v.20 no.6
• /
• pp.145-152
• /
• 2011

Salvador Dali put a title of his work as 'A Propos of the Treatise on Cubic Form by Juan de Herrera' at 1960. Through this work which is consisted in cube frame surrounding black and white letter squares and nails in the sky, he directly referred about the cube which were showed in his pictures. To understand the meaning of this work, Dali's paintings and Juan de Herrera's design and architectural ideas are analysed by building. His concerning about absolute existence like god and nuclear takes the cubic form by Juan de Herrera instead of pictorial tendencies of Cubism, however pictorial elements such as sky and nails were still used in the work. He use alphabet letter as pattern consisting wall and symbol representing 'Juan de Herrera', moreover number '2' is taken to show up line attribute. Dali had several design develop process, and finally he reached an new stage called 'Hypercube'. Hypercube can distinguish from Cubism and Herrera's architectural idea, and it will be free from objective world based in Euclid geometry. Although cubic is the simplest shape. It can contain the variety of developments in these fields - philosophy, architecture, painting and etc.- from Platon to nuclear physics and coexists in a picture of Salvador Dali.

• Wind and Structures
• /
• v.13 no.6
• /
• pp.487-498
• /
• 2010

When designing structures to the wind action, the variation of the mean wind velocity and turbulence parameters with the height above the ground must be taken into account. This paper presents the numerical simulation results of atmospheric boundary layer (ABL) airflows, in a numerical domain with no obstacles and with a cubic building. The results of the flow characterization, obtained with the FLUENT CFD code were performed using the ${\kappa}-{\varepsilon}$ turbulence model with the MMK modification. The mean velocity and turbulence intensity profiles in the inflow boundary were defined in accordance with the Eurocode 1.4, for different conditions of aerodynamic roughness. The maintenance of the velocity and turbulence characteristics along the domain were evaluated in an empty domain for uniform incident flow and the ABL Eurocode velocity profiles. The pressure coefficients on a cubic building were calculated using these inflow conditions.

• Asian Journal of Atmospheric Environment
• /
• v.12 no.1
• /
• pp.47-58
• /
• 2018

The aim of this work is to investigate the effect of atmospheric stability on near-field pollutant dispersion from rooftop emissions of a single cubic building using computational fluid dynamics (CFD). This paper used the shear stress transport (here after SST) k-${\omega}$ model for predicting the flow and pollutant dispersion around an isolated cubic building. CFD simulations were performed with two emission rates and six atmospheric stability conditions. The results of the simulations were compared with the data from wind tunnel experiments and the result of simulations obtained by previous studies in neutral atmospheric condition. The results indicate that the reattachment length on the roof ($X_R$) obtained by computations show good agreement with the experimental results. However, the reattachment length of the rooftop of the building ($X_F$) is greatly overestimated compared to the findings of wind tunnel test. The result also shows that the general distribution of dimensionless concentration given by SST k-${\omega}$ at the side and leeward wall surfaces is similar to that of the experiment. In unstable conditions, the length of the rooftop cavity was decreased. In stable conditions, the horizontal velocity in the lower part around the building was increased and the vertical velocity around the building was decreased. Stratification increased the horizontal cavity length and width near surface and unstable stratification decreased the horizontal cavity length and width near surface. Maintained stability increases the lateral spread of the plume on the leeward surface. The concentration levels close to the ground's surface under stable conditions were higher than under unstable and neutral conditions.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.173-173
• /
• 2006

We have explored a strategy to control the supramolecular nano-structures self-assembled from rigid segments through attachment of flexible chains through microphase separation and anisotropic arrangement. Supramolecular structures formed by self-assembly of rigid building blocks can be precisely controlled from 1-D layered, 3-D bicontinuous cubic to 2-D cylindrical structures by systematic variation of the type and relative length of the respective blocks. Furthermore, depending on the individual molecular architectures, rigid building blocks self-assemble into a wide range of supramolecular structures such as honeycomb, disk, cylinder, helix, tube, barrel stave, and nano-cage.

• Advances in environmental research
• /
• v.4 no.3
• /
• pp.173-181
• /
• 2015

This article outlines a case study of water and energy savings in a typical building through a modelling process and analysis of simultaneous water-energy saving measures. Wet cooling towers are one of the most important equipments in buildings with a considerable amount of water and energy consumption. A variety of methods are provided to reduce water and energy consumption in these facilities. In this paper, thorough the modeling of a typical building, water and energy consumption are measured. Then, After application of modern methods known to be effective in saving water and energy, including the ozone treatment for cooling towers and shade installation for windows, i.e. fins and overhangs, the amount of water and energy saving are compared with the base case using the Simergy model. The annual water consumption of the building, by more than 50% reduction, has been reached to 500 cubic meters from 1024 cubic meters. The annual electric energy consumption has been decreased from 405,178 kWh to 340,944 kWh, which is about 16%. After modeling, monthly peak of electrical energy consumption of 49,428 has dropped to 40,562 kWh. The reduction of 18% in the monthly peak can largely reduce the expenses of electricity consumption at peak.

• Journal of Welding and Joining
• /
• v.27 no.5
• /
• pp.42-48
• /
• 2009

Pipe welding is used in various ranges such as civil engineering and ship building engineering. Until now, many technicians work for pipe welding manually under harmful, dangerous and difficult conditions. So it is necessary to install automation process. For automation pipe welding, relation between welding parameters & bead shape should be considered. Using this relation, bead shape could be expected from welding parameters. FCAW was used in this study. Instead of pipe workpiece, fillet joint plate is used, which were inclined 0,45,90,135,180 degree. By analyzing between welding parameters (current, welding speed, voltage) and bead shape parameters with non-linear multiple regression, bead shape parameters could be expected. Piecewise Cubic Hermite Interpolation was used to expect smooth curved bead shape with bead shape parameters. From these processes, bead shape could be expected from welding parameters.

• Earthquakes and Structures
• /
• v.2 no.4
• /
• pp.323-336
• /
• 2011

The problem of reconstruction of complete building response from a limited number of response measurements is considered. The response at the intermediate degrees of freedom is reconstructed by using piecewise cubic Hermite polynomial interpolation in time domain. The piecewise cubic Hermite polynomial interpolation is preferred over the spline interpolation due to its trend preserving character. It has been shown that factorization of response data in variable separable form via singular value decomposition can be used to derive the complete set of normal modes of the structural system. The time domain principal components can be used to derive empirical transfer functions from which the natural frequencies of the structural system can be identified by peak-picking technique. A reduced-rank approximation for the system flexibility matrix can be readily constructed from the identified mass-orthonormal mode shapes and natural frequencies.