• 한국산학기술학회논문지
• /
• 제12권3호
• /
• pp.1070-1077
• /
• 2011

본 논문은 초음파 가공에 의한 용착성을 가공조건의 영향에 관하여 나타내었다. 한파장 혼의 최적화를 이용한 Ni-Cu 이종금속 박판의 용착성 평가는 초음파 가공 방법을 이용하여 확인된다. 초음파 가공변수 설정에 따른 인장시험을 통한 최적의 용착조건을 제시하였으며 SEM 사진과 EDX-ray 분석에 의한 용착성을 평가하였다. 실험적 연구는 초음파 가공 후 인장강도의 측정, SEM사진 분석으로 수행된다. 또한 가공시간, 가압력, 진폭의 가공변수들은 본 연구에 적용되었다.

• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.383-390
• /
• 1992

We investigated the effect of substrate on the properties of the Ni-Zn-Cu ferrite thin films deposited on SiO2 (1000∼3000${\AA}$) / Si (100) substrate at various conditions by rf magnetron sputtering. A disktype Ni-Zn-Cu ferrite sintered by conventional ceramic process and argon gas were used as a target and a sputtering gas, repectively. The compositions of the thin films measured by EPMA were similar to target composition (Fe: 65.8 at%, Ni: 12.7 at%, Cu: 6.7 at%, Zn: 14.8 at%) irrespective of substrate temperature. Amorphous thin films were deposited when substrate was not intentionally heated, but the films came to crystallize with increasing substrate temperature, and crystalline thin films were deposited at substrate temperature above 200$^{\circ}C$. Below 250$^{\circ}C$ saturation magnetization (Ms), remanence (Mr) and coercivity (Hc) of the ferrite thin film increased with the substrate temperature due to the increase of grain size and the improvement of crystallinity. And above 250$^{\circ}C$, Ms, Mr increased slightly, but Hc of the amorphous thin films increased due to crystallization, whereas that of the crystalline thin films decreased because of grain growth and stress release.

• 열처리공학회지
• /
• 제25권6호
• /
• pp.292-298
• /
• 2012

In this study, Cu-2.5at.%Ni-1at.%Si alloys were fabricated by horizontal continuous casting system to improve the electrical conductivity and mechanical properties of Cu-Ni-Si alloy. Withdrawing speed was changed with 50, 100, 150 and 200 mm/min for the optimum manufacturing condition. Microstructure was observed using OM, FE-SEM and TEM. Electrical conductivity was measured by 4-point probe method and mechanical properties were tested. A horizontal continuous cast thin slab had sound macro and micro structures with partly crystallized structures. Electrical resistivity decreased with increasing annealing temperature from 250 to $850^{\circ}C$, with increasing annealing temperature The maximum hardness and tensile strength were Hv 130, 610 MPa at $550^{\circ}C$, respectively. With changing withdrawing speed from 50 to 150 mm/min, hardness, tensile strength, yield strength and elongation were Hv 60-65, 210-230 MPa, 65-75 MPa and 40-50%, respectively.

• 소성∙가공
• /
• 제10권7호
• /
• pp.565-572
• /
• 2001

It is well known that a multicomponent $Zr_{4l.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ bulk metallic glass alloy shows good bulk glass forming ability due to its high resistance to crystallization in the undercooled liquid state. DSC and XRD have been performed to confirm the amorphous structure of the master alloy. To investigate the mechanical properties and deformation behavior of the bulk metallic $Zr_{4l.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ alloy, a series of compression tests has been carried out at the temperatures ranging from $351^{\circ}C$ to $461^{\circ}C$at the various initial strain rates from $2{\times}10^4s^1$ to $2{\times}10^2s^1$. Three types of nominal stress-strain curves have been identified such as linear stress-strain relationship meaning fracture at maximum stress, plastic deformation including stress overshoot and steady-state flow, plastic deformation without stress overshoot depending on the strain rate and test temperature. Also DSC analysis for the compressed specimens was carried out to investigate the change of structure, thermal stability and crystallization behavior for the various test conditions.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 추계학술대회 논문집(Proceeding of the KOSME 2001 Autumn Annual Meeting)
• /
• pp.92-97
• /
• 2001

This paper was studied on the effect of temperature on corrosion of absorption refrigeration systems using LiBr-$H_2O$ working fluids. In the fresh water and 62 %lithium bromide solution at $70^{\circ}C$, polarization test of SS 400, Cu(Cl220T-OL) and Ni-Al bronze was carried out. And Polarization behavior, polarization resistance characteristics, corrosion rate(mmpy) and corrosion sensitivity of materials forming absorption refrigeration systems was considered. The main results are as following: As the experimental temperature increase, the change of corrosion rate of Ni-Al bronze become duller than SS 400 and Cu in 62 % lithium bromide solution. Open circuit potential of SS 400 is less noble than that of Cu and Ni-Al bronze in fresh water, but that becomes noble than Cu and Ni-Al bronze in 62 % lithium bromide solution. The corrosion sensitivity of Ni-Al bronze was controlled than that of Cu and SS 400 in 62% LiBr solution.

• 한국분말재료학회지
• /
• 제23권2호
• /
• pp.132-135
• /
• 2016

This study investigates the influence of sintering temperature on the magnetic properties and frequency dispersion of the complex permeability of Ni-Zn-Cu ferrites used for magnetic shielding in near-field communication (NFC) systems. Sintered specimens of $(Ni_{0.7}Zn_{0.3})_{0.96}Cu_{0.04}Fe_2O_4$ are prepared by conventional ceramic processing. The complex permeability is measured by an RF impedance analyzer in the range of 1 MHz to 1.8 GHz. The real and imaginary parts of the complex permeability depend sensitively on the sintering temperature, which is closely related to the microstructure, including grain size and pore distribution. In particular, internal pores within grains produced by rapid grain growth decrease the permeability and increase the magnetic loss at the operating frequency of NFC (13.56 MHz). At the optimized sintering temperature ($1225-1250^{\circ}C$), the highest permeability and lowest magnetic loss can be obtained.

• 약학회지
• /
• 제17권4호
• /
• pp.235-243
• /
• 1973

Determinations of the compositioin ofl chinoform metal chelates by elemental analysis and molar ratio method showed that the ratios of the ligand to metals in chinoform Cu(II) chelate, chinofrm Ni (II) chelate, and chinoform CO(II) chelate were 2:1 respectively and that the ratio in chinoform Fe(III) chelate was 3:1. It was found that diffe rential thermal values vary with the center metalic ions and that the thermal stability was in anorder of Fe>Cu>Co>Ni. The indices of over-all stability constant of chinoform Cu(II) chelate, Ni(II) chelate, Co(II) chelate, and Fe(III) chelate were 15.57, 15.16, 15.40 and 20.76, respectively, and the over-all stability was in an order of Fe>Cu>Co>Ni. The tests of the natibacterial activity in vitro of the chinoform metal chelates against Staphylococcus aureus ATCC G538, Pseudomonas aeruginosa 2131, Serratia marcescens 3357, Klebsiella pneumoniae 8899, Enterococcus 3309, Streptococcus pyogenes 507, and Escherichia coli 125 showed that the Cu(II) chelate generally had greater activity than chinoform, that it had four-fold activity particularly against Streptococcus pyogenes 507 and Staphylococcus awreus ATCC 6538, that the Ni(II) and Co(II) chelates had almost same activity, and that the Fe chelate had strong activity against Escherichia coli 125.

• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.504-512
• /
• 1999

The high-quality carbon nanofibers were prepared by chemical vapor deposition of gas mixtures of CO-H2 and C3H8-H2 over Fe-Cu and Ni-Cu bimetallic catalysts. The yield and structure of carbon nanofiber produced were altered by the change of catalyst composition and reaction temperature. The high yields were obtained around 500$^{\circ}C$ with e-Cu catalyst and around 700-750$^{\circ}C$ with Ni-Cu catalyst and the relatively higher yields were obtained with the bimetallic catalyst containing 50-90% of Ni and Fe respectively in comparison with the pure metals. The carbon nanofibers produced over the Fe-Cu catalyst at around 500$^{\circ}C$ with the maximum yields had the highest surface ares of 160-200 m2/g around 650$^{\circ}C$ which was slightly lower than the temperature for maximum yields. In order to examine the characteristics of carbon nanofibers as catalyst support Ni and Co metals were supporte on the carbon nanofibers and CO hydrogenation reaction was performed with the catalysts. The particle size distribution of Ni and Co supported over the carbon nanofibers were 6-15 nm and the CO hydrogenation reaction rate with the carbon-nanofiber supported catalysts was much higher than that over the other supports.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.342-347
• /
• 2004

The deformation behavior of a $Zr_{55}Al_{10}Ni_5Cu_{30}$ bulk metallic glass under tensile loading at different range of strain rates and temperatures between 680 K and 740 K were investigated. The variation in the deformation behavior of $Zr_{55}Al_{10}Ni_5Cu_{30}$ bulk metallic glass which resulted from the crystallization induced during testing was reported. The$Zr_{55}Al_{10}Ni_5Cu_{30}$ bulk metallic glass has showed either homogeneous or inhomogeneous deformation depending on test condition. It exhibited a maximum elongation of about 560 % at the condition of $407^{\circ}C{\times}\;10^{-4}/s$. The flow behavior exhibited three different types and the flow stress became lower at higher temperatures and lower strain rates. The increase of the time elapsed during heating resulted in the partial crystallization of bulk metallic glass phase and eventually strain hardening and brittle fracture.

• Advances in environmental research
• /
• 제3권4호
• /
• pp.321-335
• /
• 2014

Eight trace metals, Cd, Co, Cr, Cu, Mn, Ni, Pb and Zn, were measured in the urban soil of Guwahati City, Assam, India from 31 sites representing five different types of land use, residential, commercial, industrial, public utilities, and roadside. Cd and Co occurred in very low concentrations (Cd << Co) in all types of land use without any significant variation from one type of land use to another. Ni concentrations were more than those of Co, and the concentrations depended on land use pattern. Average Cr and Cu concentrations were ${\geq}100mg/kg$, but Cr had a significantly higher presence in industrial land use. Pb concentrations showed similar trends. The two metals, Mn and Zn, were present in much larger amounts compared to the others with values ${\geq}300mg/kg$. Industrial and roadside soil contained much more Mn while commercial soil was enriched with Zn. Toxicity Characteristic Leaching Procedure (TCLP) was used for elucidating the mobility characteristics of the eight heavy metals. Mn suffered the highest leaching from commercial land (9.9 mg/kg on average) and also from other types of land. Co, Cu and Pb showed higher leachability from commercial soils but the leached concentrations were less than those of Mn. The two metals, Zn and Ni, were leached from residential land in considerable amounts. The TCLP showed Mn to be the most leachable metal and Cr the least.