• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.66-66
• /
• 2009

Various alloy system, such as Cu-Sn-Ti, Cu-Ag-Ti, and Ni-B-Cr-based alloy are used for the brazing of diamond grits. However, the problem of the adhesion strength between the diamond grits and the brazed alloy is presented. The adhesion strength between the diamond grits and the melting filler alloy is predicted by the contact angle, thereby, instead of diamond grit, the study on the wettability between the graphite and the brazing alloy has been indirectly executed. In this study, Cu-13Sn-12Ti filler alloy was manufactured, and the contact angles, the shear strengths and the interfacial area between the graphites(diamond grits) and braze matrix were investigated. The contact angle was decreased on increasing holding time and temperature. The results of shear strength of the graphite joints brazed filler alloys were observed that the joints applied Cu-13Sn-12Ti alloy at brazing temperature 940 $^{\circ}C$ was very sound condition indicating the shear tensile value of 23.8 MPa because of existing the widest carbide(TiC) reaction layers. The micrograph of wettability of the diamond grit brazed filler alloys were observed that the brazement applied Cu-13Sn-12Ti alloy at brazing temperature $990^{\circ}C$ was very sound condition because of existing a few TiC grains in the vicinity of the TiC layers.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.49-58
• /
• 2010

Various alloy system, such as Cu-Sn-Ti, Cu-Ag-Ti, and Ni-B-Cr-based alloy are used for the brazing of diamond grits. However, the problem of the adhesion strength between the diamond grits and the brazed alloy is presented. The adhesion strength between the diamond grits and the melting filler alloy is predicted by the contact angle, thereby, instead of diamond grit, the study on the wettability between the graphite and the brazing alloy has been indirectly executed. In this study, Cu-13Sn-12Ti filler alloy was manufactured, and the contact angles, the shear strengths and the interfacial area between the graphites (diamond grits) and braze matrix were investigated. The contact angle was decreased on increasing holding time and temperature. The results of shear strength of the graphite joints brazed filler alloys were observed that the joints applied Cu-13Sn-12Ti alloy at brazing temperature $940^{\circ}C$ was very sound condition indicating the shear tensile value of 23.8 MPa because of existing the widest carbide(TiC) reaction layers. The micrograph of wettability of the diamond grit brazed filler alloys were observed that the brazement applied Cu-13Sn-12Ti alloy at brazing temperature $990^{\circ}C$ was very sound condition because of existing a few TiC grains in the vicinity of the TiC layers.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.175.1-175.1
• /
• 2015

CuSn thin films were deposited by rf magnetron co-sputtering method with pure Cu and Sn metal targets with a variety of rf powers. CuSn thin films were studied with a surface profiler (alpha step), X-ray photoelectron spectroscopy (XPS), X-ray induced Auger electron spectroscopy (XAES), X-ray diffraction (XRD), and contact angle measurement. The thickness of CuSn thin films was fixed at $200{\pm}10nm$ and deposition rate was calculated by the measured with a surface profiler. From the survey XPS spectra, the characteristic peaks of Cu and Sn were observed. Therefore, CuSn thin films were successfully synthesized on the Si (100) substrate. The oxidation state and chemical environment of Cu and Sn were investigated with the binding energy regions of Cu 2p XPS spectra, Sn 3d XPS spectra, and Cu LMM Auger spectra. Change of the crystallinity of the films was observed with XRD spectra. Using contact angle measurement, surface free energy (SFE) and wettability of the CuSn thin films were studied with distilled water (DW) and ethylene glycol (EG).

• 마이크로전자및패키징학회지
• /
• 제10권4호
• /
• pp.29-33
• /
• 2003

n-형 탄화규소 반도체에 대한 구리금속을 이용하여 오옴성 접촉 구조를 제작하였다. 제작된 구리접촉에 대해 후속열처리 조건과 금속접촉 구조에 따른 재료적, 전기적 성질의 변화를 조사하였다. 금속접촉의 오옴성 성질은 금속박막의 구조 뿐 아니라 열처리조건에 대해서도 크게 좌우됨을 알 수 있었다. 열처리는 급속열처리 장치를 이용한 진공상태 및 환원 분위기에서 2단계 열처리방식을 통하여 시행하였다. 접촉비저항의 측정을 위해 TLM 구조를 만들었으며 면저항 ($R_{s}$), 접합저항 ($R_{c}$), 이동거리 ($L_{T}$), 패드간거리 (d), 전체저항 ($R_{T}$) 값을 구하여 알려진 계산식에 의해 접촉비저항 ($p_{c}$) 값을 추정하였다. 진공보다 환원분위기에서 후속 열처리를 수행한 시편이 양호한 전기적 성질을 가짐을 알 수 있었다. 가장 양호한 결과는 Cu/Si/Cu 구조를 가진 금속접촉 결과이었으며 접촉비저항 ($p_{c}$)은 $1.2\times 10^{-6} \Omega \textrm{cm}^2$의 낮은 값을 얻을 수 있었다. 재료적 성질은 XRD를 이용하여 분석하였고 SiC 계면 상에 구리와 실리콘이 결합한 구리 실리사이드가 형성됨을 알 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제16권4호
• /
• pp.9-15
• /
• 2009

Cu pillar 범프를 사용한 플립칩 기술은 솔더범프를 사용한 플립칩 공정에 비해 칩과 기판 사이의 거리를 감소시키지 않으면서 미세피치 접속이 가능하다는 장점이 있다. Cu pillar 범프를 사용한 플립칩 공정은 미세피치화와 더불어 기생 캐패시턴스를 억제하기 위해 칩과 기판 사이에 큰 거리가 요구되는 RF 패키지에서도 유용한 칩 접속공정이다. 본 연구에서는 Sn 캡을 형성한 Cu pillar 범프와 Sn 캡이 없는 Cu pillar 범프를 전기도금으로 형성한 후 플립칩 접속하여 Cu-Sn-Cu 샌드위치 접속구조를 형성하였다. Cu pillar 범프 상에 Sn 캡의 높이를 변화시키며 전기도금한 후, Sn 캡의 높이에 따른 Cu-Sn-Cu 샌드위치 접속구조의 접속저항과 칩 전단하중을 분석하였다. 직경 $25\;{\mu}m$, 높이 $20\;{\mu}m$인 Cu pillar 범프들을 사용하여 형성한 Cu-Sn-Cu 샌드위치 접속구조에서 $10{\sim}25\;{\mu}m$ 범위의 Sn 캡 높이에 무관하게 칩과 기판 사이의 거리는 $44\;{\mu}m$으로 유지되었으며, 접속부당 $14\;m{\Omega}$의 평균 접속저항을 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.192-193
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electro less plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. In this paper, we investigated low-cost Ni/Cu contact formation by electro less and electroplating for crystalline silicon solar cells.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2007년도 춘계종합학술대회
• /
• pp.548-551
• /
• 2007

최근에 유기물 전계효과 트랜지스터의 연구는 전자 소자 분야에서 널리 알려져 있다. 특히 본 연구에서는 CuPc 물질을 기본으로 하여 소자를 제작하고, 또한 기판의 온도를 달리 하여 제작하였다. CuPc FET 소자는 top-contact 방식으로 제작하였으며, 기판의 온도는 상온과 $150^{\circ}C$로 달리 하였다. 또한 CuPc의 두께는 40nm로 하였고, 채널의 길이는 $50{\mu}m$, 폭은 3mm로 하였다. 제작된 소자를 이용하여 전압-전류 특성을 측정하였다.

• 마이크로전자및패키징학회지
• /
• 제16권3호
• /
• pp.67-73
• /
• 2009

Cu pillar 범프를 사용한 플립칩 접속부는 솔더범프 접속부에 비해 칩과 기판사이의 거리를 감소시키지 않으면서 미세피치 접속이 가능하기 때문에, 특히 기생 캐패시턴스를 억제하기 위해 칩과 기판사이의 큰 거리가 요구되는 RF 패키지에서 유용한 칩 접속공정이다. 본 논문에서는 칩에는 Cu pillar 범프, 기판에는 Sn 범프를 전기도금하고 이들을 플립칩 본딩하여 Cu pillar 범프 접속부를 형성 한 후, Sn 전기도금 범프의 높이에 따른 Cu pillar 범프 접속부의 접속저항과 칩 전단하중을 측정하였다. 전기도금한 Sn 범프의 높이를 5 ${\mu}m$에서 30 ${\mu}m$로 증가시킴에 따라 Cu pillar 범프 접속부의 접속저항이 31.7 $m{\Omega}$에서 13.8 $m{\Omega}$로 향상되었으며, 칩 전단하중이 3.8N에서 6.8N으로 증가하였다. 반면에 접속부의 종횡비는 1.3에서 0.9로 저하하였으며, 접속부의 종횡비, 접속저항 및 칩 전단하중의 변화거동으로부터 Sn 전기도금 범프의 최적 높이는 20 ${\mu}m$로 판단되었다.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.225-229
• /
• 2009

The front metal contact is one of the most important element influences in efficiency in the silicon solar cell. First of all selective of the material and formation method is important in metal contacts. Commercial solar cells with screen-printed contacts formed by using Ag paste process is simple relatively and mass production is easy. But it suffer from a low fill factor and a high shading loss because of high contact resistance. Besides Ag paste too expensive. because of depends income. This paper applied for Ni/Cu metallization replace for paste of screen printing front metal contact. Low cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the screen-printed Ag contacts. Ni has been proposed as a suitable silicide for the salicidation process and is expected to replace conventional silicides. Copper is a promising material for the electrical contacts in solar cells in terms of conductivity and cost. In experiments Ni/Cu metal contact applied same grid formation of screen-printed solar cell. And it has variation of different grid spacing. It was verified that the wide spacing of grid finger could increase the series resistance also the narrow spacing of grid finger also implies a grid with a higher density of grid fingers. Through different grid spacing found alteration of efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.166-169
• /
• 2006

We fabricated hexagonal copper sulfide $Cu_2S$ nanowires to obtain a larger contact area of $Cu_2S/CdS$ solar cell. Copper sulfide nanowires were grown on Cu foil at room temperature by gas-sol id reaction. The size, density and shape of nanowires seemed to be affected by the change or reaction time temperature, crystallographic orientation of Cu foil, and molar ratio of the mixed gas. We controled the length and the diameter of the nanowires and we obtained suitable nanowire arrays which has fitting size for uniform deposition with n-type CdS. CdS layer was deposited on the nanowire array by electrodeposition and it seemed to be uniform. The $Cu_2S/CdS$ nanowires/CdS junction showed diode characteristics, A large contact area is expected with the $Cu_2S/CdS$ nanowire structure as compared with the $Cu_2S/CdS$ thin film.