• Journal of the Korean Vacuum Society
• /
• v.13 no.2
• /
• pp.79-85
• /
• 2004

Secondary ion mass spectrometry(SIMS) and glow discharge mass spectrometry(GDMS) were used to determine the impurity concentrations of hydrogen, carbon, and oxygen elements in the Cu and Ta films, and the results of SIMS and GDMS analysis were carefully considered. The Cu and Ta films were deposited on Si (100) substrates at zero substrate bias voltage and a substrate bias voltage of -50 V(Cu films) or -125 V(Ta films) using a non-mass separated ion beam deposition method. As a result of SIMS with Cs+ ion beam, in the case of the Cu and Ta films deposited without the substrate bias voltage, many strong peaks were observed, which is considered to be detected as a the cluster state such as CxHx, OxHx, CxOxHx. All the peaks of SIMS results could be interpreted by the combination of these dominant impurities. Moreover, it was confirmed that the quantitative results of GDMS analysis were accordant to the SIMS results.

• Journal of information and communication convergence engineering
• /
• v.4 no.4
• /
• pp.158-161
• /
• 2006

[ $Bi_2Sr_2Ca_nCu_{n+1}O_y(n{\geq}0)$ ] thin film is fabricatedvia two different processes using an ion beam sputtering method i.e. co-deposition and layer-by-layer deposition. A single phase of Bi2212 can be fabricated via the co-deposition process. While it cannot be obtained by the layer-by-layer process. Ultra-low growth rate in our ion beam sputtering system brings out the difference in Bi element adsorption between the two processes and results in only 30% adsorption against total incident Bi amount by layer-by-layer deposition, in contrast to enough Bi adsorption by co-deposition.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.8
• /
• pp.2201-2206
• /
• 2010

To improve the separation property and stability of metal chelate Cu(II) column, three new kinds of multidentate aminocarboxy silica columns with cation-exchange properties were synthesized using glutamic acid (Glu), glutamic acidbromoacetic acid (Glu-BAA), glutamic acid-bromosuccinic acid (Glu-BSUA) as ligands and silica gel as matrix. The standard proteins were separated with prepared chromatographic columns. The stationary phases exhibited the metal chelate property after fixing copper ion (II) on the synthesized multidentate ligand silica columns. The binding capacity of immobilized metal ion was related with the dentate number of multidentate ligands. Chromatographic behavior of proteins and the leakage of immobilized metal ion on multidentate chelate Cu(II) columns were affected by the dentate number of multidentate ligands and competitive elution system directly. The results showed that quinquedentate Glu-BSUA-Cu(II) column exhibited better chromatographic property and stability as compared with tridentate Glu-Cu(II) column, tetradentate Glu-BAA-Cu(II) column and commonly used IDA-Cu(II) column.

• Journal of the Korean Chemical Society
• /
• v.24 no.6
• /
• pp.421-425
• /
• 1980

The EPR absorption of furan compounds adsorbed on CuY zeolite was studied. With the adsorption of furan on CuY a new high field having a width of 8 gauss and g-factor of 2.002 appeared in EPR spectrum, while the original signal of Cu(Ⅱ) decreased. When 2-methylfuran was adsorbed on Cu(15)Y a new absorption band with a hyperfine structure appeared. With the increase of the degree of Cu(Ⅱ) ion exchange the resolution of the hyperfine structure became poor. The appearance of the new band was interpreted in terms of the formation of a charge transfer complex between Cu(Ⅱ) ion and the furan ring.

• Journal of the Korean Magnetics Society
• /
• v.12 no.5
• /
• pp.184-188
• /
• 2002

The Cu/Ni/Cu(002)/Si(100) films which have perpendicular magnetic anisotropy were deposited by e-beam evaporation methods. From the reflection high energy electron diffraction pattern, the films were confirmed to be grown epitaxially on silicon. After 2X lots ions/$\textrm{cm}^2$ C+ irradiation, magnetic easy-axis was changed from surface normal to in-plane as shown in the hysteresis loop of magneto-optical Kerr effects. It became manifest from analysis of X-ray reflectivity and grazing incident X-ray diffraction that even though interface between top Cu layer and Ni layer became rougher, the contrast of Cu and Ni's electron density became manifest after ion irradiation. In addition, the strain after deposition of the films was relaxed after ion irradiation. Strain relaxation related with change of magnetic properties and mechanism of intermixed layer's formation was explained by thermo-chemical driving force due to elastic and inelastic collision of ions.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.2
• /
• pp.73-80
• /
• 1998

The aim of this study is to develop sintered stainless steels (SSS) with good mechanical strength, wear resistance, and corrosion resistance by nitrogen ion implantation on the Culated SSS surface. Stainless steel compacts containg Cu (2-10 wt%) were prepared by electroless Cu-pating method which results in the increased3 homogenization in alloying powder. Nitrogen ion implantation was carried out by using N2 gas as the ion source. Nitrogen ions were embedded by an acceleratol of 130keV with doese $3.0\times10^{17}\;ions/\textrm{cm}^2$ on the SSS at $25^{\circ}C$ in$2\times10^{-6}$ torr vacuum. The nitrogen ion implanted SSS obtained from anodic ploarization curves revealed higher corrosion potential than that of nitrogen ion unimplante one. And nitrogen ion implanted 316LSSS had good resistance to pitting corrosion due to the synergistic effect of Mo and N, and the inhibition of $NH_4\;^+$<\TEX>, against $CI^-$<\TEX>.

• Journal of Electrochemical Science and Technology
• /
• v.11 no.1
• /
• pp.92-98
• /
• 2020

SnO₂-based high-capacity anode materials are attractive candidate for the next-generation high-performance lithium-ion batteries since the theoretical capacity of SnO₂ can be ideally extended from 781 to 1494 mAh g^-1. Here 3D etched Cu foam is applied as a current collector for electron path and simultaneously a substrate for the SnO₂ coating, for developing an integrated electrode structure. We fabricate the 3D etched Cu foam through an auto-catalytic electroless plating method, and then coat the SnO₂ onto the self-supporting substrate through a simple sol-gel method. The catalytic dissolution of Cu metal makes secondary pores of both several micrometers and several tens of micrometers at the surface of Cu foam strut, besides main channel-like interconnected pores. Especially, the additional surface pores on etched Cu foam are intended for penetrating the individual strut of Cu foam, and thereby increasing the surface area for SnO₂ coating by using even the internal of Cu foam. The increased areal capacity with high structural integrity upon cycling is demonstrated in the SnO₂-coated 3D etched Cu foam. This study not only prepares the etched Cu foam using the spontaneous chemical reactions but also demonstrates the potential for electroless plating method about surface modification on various metal substrates.

• Applied Microscopy
• /
• v.45 no.4
• /
• pp.236-241
• /
• 2015

Carbon-coated Ni, Cu and Sn nanocapsules were investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM) and a four-point probe device. All of these nanocapsules were prepared by an arc-discharge method, in which the bulk metals were evaporated under methane ($CH_4$) atmosphere. Three pure metals (Ni, Cu, Sn) were typically diverse in formation of the carbon encapsulated nanoparticles and their different mechanisms were investigated. It was indicated that a thick carbon layers formed on the surface of Ni(C) nanocapsules, whereas a thin shell of carbon with 1~2 layers covered on Cu(C) nanocapsules, and the Sn(C) nanocapsules was, in fact, a longger multi-walled carbon nanotubes partially-filled with metal Sn. As one typical magnetic/dielectric nanocomposite particles, Ni(C) nanocapsules and its counterpart of oxide-coated Ni(O) nanocapsules were compared in the electrically conductive behaviors for further applications as the electromagnetic materials.

• Journal of environmental and Sanitary engineering
• /
• v.24 no.2
• /
• pp.31-39
• /
• 2009

In this research, I carried out the adsorption and removal test of Pb, Ni, Co and Cu ions using organic substances spread out any where in the nature which can be obtained easily from our neighbor-such as Paulownia coreana, Pinus densiflora, Juniperus chinesis, Quercus dentata, Magnolia kobus, Platanus occidentalis, Gingko biloba, Diospyros kaki leaves. As the result of the research to find the best optional condition for the adsorption and removal, shows that the adsorption and removal ratio of Pb ion by a Paulownia coreana raw leaves is 99% at $70^{\circ}C$, those of Ni ion and Co ion by Magnolia kobus formalin treatment leaves are 79% at $70^{\circ}C$, 97% at $40^{\circ}C$ respectively. And that of Cu ion by Platanus occidentalis treatment leaves is 97% at $50^{\circ}C$ in mixed solution. As the result of comparing the removal ratio by raw leaves and formalin treatment leaves, the removal ratio of treatment is 30~90% more effective than raw leaves in most cases. And I concluded Pb > Cu > Co > Ni ion in multiple solution and Co > Ni > Cu >Pb ion in single solution after testing adsorption and removal ratio of mixed solution separately as time goes by. In general, the reactions were completed within first 5 minutes. The test result of measuring the hydrolysable tannin content of each leaf shows that an overcup Quercus dentata is 11.36%, a Diospyros kaki is 10.81% and the rest of them are 2.49~4.12% in raw leaves cases. In treatment leaves cases, an overcup Quercus dentata is 3.23% and the others are less than 1%.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.5
• /
• pp.406-409
• /
• 1995

The complex formation from Cu(Ⅱ) ion and 2,2-bis(hydroxymethyl)-2,2',2"-nitrilotriethanol (Bistris) in aqueous solution has been studied potentiometrically and spectrophotometrically. Bistris (L) coordinates to Cu(Ⅱ) as tridentate. The complex CuL2+ undergoes deprotonation in neutral and basic media. The deprotonated complexes involve metal-alcoholate coordinate bond in stable chelate structures.