• Archives of Pharmacal Research
• /
• 제12권3호
• /
• pp.214-218
• /
• 1989

Atmospheric particulate matters (A. P. M. ) were collected on quartz-fiber filters from March 1985 to May 1986, using the Andersen high-volume air sampler and contents of six heavy metals (Fe, Mn, Cu, Zn, Pb Ni) in the A. P. M. were determined by atomic absorption spectrophotometry. These heavy metals were divided into the three groups with respect to their particle size distribution. Fe and Mn were mainly associated with coarse particles (diameter > 2.0 $\mu$m), but Pb and Ni were related fine particles (diameter < 2.0 $\mu$m). Cu and Zn had mized size distributions in both of them. In the seasonal variation of heavy metals, the contents of Fe and Mn in spring and Ni and Pb in winter were higher than any other season. There were high mutual correlation between Fe and Mn coarse particles, and between Pb and Ni in fine particles.

• 마이크로전자및패키징학회지
• /
• 제23권3호
• /
• pp.51-56
• /
• 2016

내산화 특성을 가지는 구리(Cu) 기반의 미세 도전 필러를 제조하기 위하여 서브마이크론급의 은(Ag) 코팅 Cu 입자를 제조하고, 그 내산화 특성을 평가하였다. 평균 크기 $0.705{\mu}m$의 Cu 입자들을 습식 합성법으로 제작한 후, 에틸렌글리콜 용매를 사용한 연속 공정으로 Ag 도금을 실시하여 Ag 도금 Cu 입자를 제조하였다. Ag 도금 공정에서 제어한 주요 변수는 환원제 아스코빅산의 첨가 농도, Ag 전구체 용액의 주입속도 및 혼합 용액의 교반속도였는데, 이들의 변화에 따른 Ag 도금의 특성과 미세한 순수 은Ag 입자의 생성 변화를 관찰하였다. 그 결과 공정변수들을 최적화시킴으로써 불필요한 순수 Ag 입자들이 생성을 막고, Ag 도금 Cu 입자들간의 응집을 억제할 수 있었다. 최적 제조조건에서 제조된 Ag 도금 Cu 입자들은 다소간의 응집을 나타내었으나, 대기중에서 $10^{\circ}C/min$의 승온속도로 가열 시 약 $225^{\circ}C$에서야 0.1%의 무게 증가를 나타내었고, $150^{\circ}C$의 대기중에서는 75 분까지 무게 증가가 없는 우수한 내산화 특성을 나타내었다.

• 한국분말재료학회지
• /
• 제7권1호
• /
• pp.12-18
• /
• 2000

Effects of the microstrucrure of rapidy solidified Al-Pb-Cu-Mg alloys on the wear investigated. In order to overcome the miscility gap between Al and pb under equilibrium conditions, both in the solid and the liquid states, the alloy were rapidy solidifies to produce them in a segregation-free condition. Although the Pb particles showed relatively fine dispersion in the Al matrix in all the alloys by this process. the Al-16Pb alloy was found to have the most favorable microstructure with discretre with discrete Pb particles of abount 0.5 ${\mu}$m in size. With the addition of Cu and Cu-Mg to Al-16Pb, cellular structures were newly formed; not seen in the binary Al-Pb alloy. Wear properties of the Al-Pb binary alloys measured as a function of the sliding speen, sliding distance, and applied load showed that the Al-16Pb alloy has the best wear resistance, as expected from the fine microstructural features in this alloy. The were resistance of the alloy containing Cu-and Cu-Mg was higher than that of the Al-16Pvb alloy, due to matrix strengthening by precipitation hardeing. The wear mechanism was identified by examining the traces and wear debris.

• 한국재료학회지
• /
• 제15권4호
• /
• pp.263-270
• /
• 2005

In order to prepare the uniform copper particles from copper chloride solution, the reduction behavior of copper particles from copper chloride and the effects of reduction agent and dispersing agent was investigated. In the case that 2.56 M of $C_6H_8O_6$ was used as a reduction agent, the highly dispersed Cu particles with sharp size distribution were generated from 0.96M of copper chloride solution, and the size of Cu particles was $6\~10\;{\mu}m$. To form $Cu(NH_3)_4Cl_2$ complex solution, $NH_4OH$ was added in the copper chloride solution before the reductive reaction of Cu ion. The generated Cu particles have a two kind of shape, spherical and rod-like. In the case that $N_2H_4{\cdot}H_2O$ was used as a reduction agent, the very fine spherical Cu particles with the size of $0.2\~0.5\;{\mu}m$ was obtained. Arabic gum as a dispersing agent was more effective than $Na_4P_2O_7{\cdot}10H_2O$.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1992년도 추계학술발표강연 및 논문개요집
• /
• pp.16-16
• /
• 1992

We have studied the effect of platinum addition on the supercon ducting properties of YB $a_2$C $u_3$$O_{7-x}$ (123) compound and elucidated the mechanism of fine dispersion of $Y_2$BaCu $O_{5}$(211) particles in YB $a_2$C $u_3$$O_{7-x}$ superconductor prepared by melting method from the metallurgical point of view. In this study, BaCu $O_2$ and CuO-rich phase unreacted during the peritecitc reaction markedly decreased by the 211 powder addition. The 211 particle of Pt-fee sintered samples exhibited 8~10$\mu$m in size, but in 1wt%Pt-added sample, 211 particles were finely dispersed in 123 matrix and the size of 211 particle was about 1~2$\mu$m. And, the critical temperature( $T_{c. zero}$) of Pt doped samples was 91.5K and the transport critical current density ( $J_{c}$) of Pt-doped samples was much more than 10$^4$A/$\textrm{cm}^2$. The high $J_{c}$ and fine dispersion of 211 particles of Pt doped YB $a_2$C $u_3$$O_{7-x}$ superconductor are attributed to $Ba_4$CuP $t_2$ $O_{8}$ compounds formed during the partial melting, which were considered als nucleation sites of 211 particles, rather than Pt inself.han Pt inself.

• Applied Microscopy
• /
• 제25권1호
• /
• pp.130-138
• /
• 1995

TEM specimen preparation methods have been examined to characterize Cu oxide particles in the polyimide film. Polyimide films were prepared by coating polyamic acid onto Cu films which had been deposited on TEM-mask and glass substrates and Cu foil, followed by thermal curing. In case of TEM-mask, direct observation was possible without further preparation. In other cases, TEM specimen were made by separating polyimide film from the substrate. Polyimide films were removed from glass and Cu foil by dissolving glass in HF solution and Cu foil in $H_{2}SO_{4}$ solution. TEM-mask observation confirms that fine $Cu_{2}O$ particles precipitate in the polyimide as a result of reaction of polyamic acid with Cu. However $Cu_{2}O$ particle reacts with HF and $H_{2}SO_{4}$ solution during dissolving the substrate and interpretation could be misled. It is concluded characterization of $Cu_{2}O$ particle in polyimide using TEM-mask is better than other methods.

• 한국주조공학회지
• /
• 제22권1호
• /
• pp.35-41
• /
• 2002

To improve the reliability of solder joints, a composite solder which consists of solder matrix and intermetallic reinforcements was manufactured by a new method. The cast ingot of Sn-6.9Cu-2.9Ag alloy had primary Cu6Sn5 intermetallics in the form of dendrites. After rolling the ingot, the intermetallic dendrites were crushed into fine particles and distributed uniformly throughout the solder matrix. As the rolled strips became thinner, the average size of the crushed particles reached a critical size which did not decrease any more by further rolling. The critical size was nearly the same as the average width of intermetallic dendrite trunk. The crushed intermetallic particles did not melt and remained in solid state during reflow soldering due to their high meltingterm-perature. The coarsening and gravitational segregation of the particles were observed during reflow soldering.

• 환경위생공학
• /
• 제19권4호
• /
• pp.9-18
• /
• 2004

In this study, the observation data for the yellow sandy dust phenomena from the year 1999 to 2003 at background sites in Korea were collected at Global Atmospheric Observatory at An-Myeon island and its temporal variation were analyzed. The chemical characteristics of the fine particles were also analyzed in order to evaluate sources of the yellow sandy dust particles. The results showed that the monthly average mass concentration of the fine particles was the highest in springtime and the lowest in summertime in general. The magnitude of its variation was also the highest in March in which the occurrence of yellow sandy dust was the most frequent and thus the number of samples was the largest, while the lowest in June through September. The yearly variation of ion components contributions to the total mass concentration of the fine particles was slowly decreasing, showing that $63\%$ in 1999, $59\%$ in 2000 and $56\%$ in 2003. The most prevalent ion components in the fine particles were found to be $NO_3$ and $SO_4^{2-}$, which are known to be source materials of acidic precipitation, and $NH_4^+$, a neutralizing material of the acid precipitation. Relative proportion of metal components in the fine particles was calculated as $14\%$ in average, and their concentrations are in an order of Fe > Al > Na > Ca > Zn > Pb > Cu > Mn > Ni > Cd > Cr > Co > U. The results indicated that main sources of the metals was soil-originated Fe, Al, Ca, and Mg, and the contribution of anthropogenic air Pollution-originated Zn, Pb, Cu, Mn were also high and keep slightly increasing. Statistical analysis showed that the chemical components could be divided into soil-originated group of Mg, Al, Ca, Fe, and Mn and air pollution-originated group of $NO_3$, Zn, Pb, and they are occupying more than $60\%$of all the components in the dusty sand. The results explain that An-Myeon island is more influenced by soil-originated source than ocean-originated one and also the influencing strength of anthropogenic poilution-originated source is less than $50\%$ of that of soil-originated sources. Compared to non-yellow sandy period, the yellow sandy dust period showed that the amounts of soil-originated $Mg^{2+}$ and $Ca^{2+}$ and ocean-originated $Na^+$ and $Cl^-$ were increased to more than double and the metals of Mg, Al, Ca, Fe were also highly increased, while micro metal components such as Pb, Cd, Zn, which have a tendency of concentrating in air, were either decreased or maintained at nearly constant level. In the period of yellow sandy dust, a strong positive correlation was observed between water soluble ions and between metals in terms of its concentration, respectively. Factor analysis showed that the first group being comprised of about $43\%$ of the total inorganic components was affected by soil and they are ions of $Na^+,\;Mg^{2+}\;and\;Ca^{2+}$ and metals of Na, Fe, Mn and Ni. The result also showed that the metals of Mg and Cr were classified as second group and they were also highly affected by soil sources.

• 열처리공학회지
• /
• 제14권2호
• /
• pp.96-102
• /
• 2001

$Al_2O_3$-copper alloy has been successfully made by gas atomization, mechanical alloying and hot pressing. In order to investigate microstructure and phase, it has been studied by using scanning electron microscope, transmission electron microscope and X-ray diffractometor. Mechanical properties have been examined using hardness tester and compressive tester according to annealing temperature. Although comparatively large Cu-Al powders are milled, the reaction between Cu-Al and $Cu_2O$ occurs and very fine $Al_2O_3$ particles in the matrix particles (5-10nm) are obtained. Compressive strength of this alloy is more than that of GlidCop Al60.

• 한국수소및신에너지학회논문집
• /
• 제18권3호
• /
• pp.238-243
• /
• 2007

The composite powder of Cu and YSZ was synthesized for a high temperature electrolysis cathode by mechanical milling. The average Cu particle size was reduced to 5 micro-meter from 48 micro-meter after the mechanical ball milling. The composite powder showed that Cu particles were uniformly covered with finer YSZ particles. Sub-micron sized pores were uniformly dispersed in the Cu/YSZ composit. Homogeneously-dispersed fine YSZ in the composite is expected to the increase in triple phase boundaries, thereby leading the enhanced performance of cathode.