• Journal of the Korean institute of surface engineering
• /
• v.43 no.1
• /
• pp.1-6
• /
• 2010

The effect of organic additives, 1-(3-sulfoproyl)-2-vinylpyridineium hydroxide (SVH) and thiourea (TU), on the precision copper electrodeposition was investigated with optical, electrochemical and x-ray diffraction techniques. It was found that SVH played a r ole as a n accelerator and TU as an i nhibitor during the electroreduction of cupric ions in acidic Cu electroplating solution. Through electrochemical measurements, TU showed more strong interaction with cupric ions than SVH and dominated overall Cu electroplating process when both additives were present in the solution. In the case of three dimensional Cu electrodeposition on the 20 ${\mu}m$-patterned Ni substrates, SVH controlled the upright growth of Cu electrodeposits and so determined its flatness, while TU prohibited the lateral spreading of Cu in the course of pulse-reverse pulse current adaptation. With microscopic observation, we obtained the optimum organic additives composition, that is, 100 ppm SVH and 200 ppm TU during the current pulsation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1771-1776
• /
• 2011

In this paper, as an attempt to improve the preparation conditions of $YBa_2Cu_3Ox$ superconducting bulk samples, the properties of $YBa_2Cu_3Ox$ superconductor depending on the particle size of YBCO powder and $BaPbO_3$ as an additive have been investigated, and a study on the effects of additive to the density, grain alignment, and porosity of samples that affect the critical current of superconductor has been performed. In order to prepare superconductor, $YBa_2Cu_3Ox$ powder synthesized by sol-gel method, showing a size distribution of 0.2~1 ${\mu}m$ was used. The $BaPbO_3$ added to promote grain growth and to decrease porosities and weak links between grain boundaries of $YBa_2Cu_3Ox$ superconductors. In the samples prepared by sol-gel synthesized powder with 10, 20, and 30 wt% conductive $BaPbO_3$ additives, the sample with 20 wt% $BaPbO_3$ obtained the highest critical current of 4.74 A, showing 20 wt% higher critical current than that with solid state synthesized powder.

• Clean Technology
• /
• v.14 no.3
• /
• pp.160-165
• /
• 2008

The synthesis of dimethyl carbonate (DMC) with Cu catalysts was investigated in a semi-batch high-pressure reactor. DMC was synthesized via the direct oxidative carbonylation of carbon monoxide with oxygen in methanol. The corrosion rate was evaluated fie the weight change for SUS test pieces which had been added into the reactor. In order to reduce the corrosion rate without significantly losing DMC yield, various additives such as amines, olefins, and other metal salts were used. When 1-methylimidazole was used as an additive, 18.6% of DMC yield could be obtained without corrosion. If the amount of 1-methylimidazole was decreased, a high DMC yield (33.2%) could be obtained with a low corrosion rate (0.5%).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.396-396
• /
• 2012

산업 분야에서 TiN, CrN, CrAl-N, TiAl-N과 같은 Hard 코팅들은 기계적 특성이 우수하여 절삭 공구, 기계 부품분야에서 많이 사용되고 있다. 최근 연구 동향을 살펴보면 기존에 하나 또는 두가지 합금상태의 Hard 코팅을 넘어서 제3원소, 제4원소를 첨가하여 미세 구조적 변화를 통해 기존의 우수한 특성에 고온안정성, 내식성, 내산화성 등 다양한 기능성을 부여하는 다기능성 연구가 활발히 진행 중이다. 본 연구에서는 마그네트론 스퍼터를 이용하여 고경도 코팅인 Ti-Al계열에 Si, Cu, Cr, B을 첨가함에 따른 내식특성을 확인해보았다. 성분이 균일한 코팅을 만들기 위해 Ti-Al, Ti-Al-Si, Ti-Al-Cu, Ti-Al-Cr, Ti-Al-B 단일합금타겟을 제조하여 실험을 진행하였다. 기본 물성을 확인하기 위해 경도 측정과 SEM XRD 등을 분석하였다. 내식성 평가는 동전위 테스트와 염수분무 테스트를 진행하였고 전해질은 염수와 동일한 5%-NaCl로 진행하였다. 그 결과 Ti-Al-Cr이 내식성에 강한 것으로 나타났고 염수분무 실험에서도 1200시간 이상 지속되는 성과를 보였다.

• Journal of Animal Science and Technology
• /
• v.47 no.4
• /
• pp.537-546
• /
• 2005

An experiment was conducted to determine the effect of supplementation of chlortetracycline (CTC,110ppm), copper sulfate(Cu, 125ppm) and two levels of probiotics(Prob I, 0.04%, Prob II, 0.1%), Bacillus licheniformis and Bacillus subtilis) on growth performance, nutrient digestibility and manure characteristics in growing pigs. A total of 50 pigs that averaged 20.78$\pm$0.35kg BW and 50$\pm$2.3d age were allocated in a randomized block design with two pigs per pen and 5 pens per treatment. Pigs and feeders were weighed 10-days interval for the 40-d trials to determine ADG, ADFI and feed:gain ratio(F:G). Average daily gain, feed intake, feed/gain and nutrient digestibility were not improved(P>0.10) by the supplementation of CTC, Cu and two levels of probiotics. There were significant(P<0.05) Cu effects on digestibility of crude protein, and probiotics effects on digestibilities on organic matter, crude protein and energy between first 20 days and subsequent 20 days. Fecal concentrations of copper were highly increased(P<0.001) by the copper supplementation. Total bacteria and coliform counts were not altered by the supplementation of CTC, Cu and two levels of probiotics. Ammonia emission from slurry, measured during first 3 weeks, was reduced (P<0.001) in pigs fed diet with 125 ppm copper from copper sulfate. Results indicate that CTC, Cu and Probiotics supplementation had a little or not positive effect on grower pig performance under sound environmental conditions. Further studies may be warranted to investigate the effects of dietary copper-either reduced or in combination with dietary ammonia control agents-on the ammonia emission characteristics of swine manure.

• ETRI Journal
• /
• v.13 no.2
• /
• pp.42-53
• /
• 1991

고유전율 적충세라믹 커패시터 소재인 $BaTiO_3$ 자기물은 일반적으로 큐리오도인 약 $120^{\circ}C$부근에서 유전율이 최고 약 10,000정도로 증가한 다음 급격히 감소하므로 적절한 이동체를 첨가하여 큐리온도를 상온으로 이동시켜 상온에서 최대 유전율을 이용하여야 한다. 그리고$BaTiO_3$ 자기물은 $1300^{\circ}C$이상의 고온소결시 고가인 Pd전극이 요구된다. 그러나 자기물의 소결온도를 저온화화면 저가의 Ag합금으로 전극재료를 대체할 수 있다. 본 연구에서는 이동제로서 $CaSnO_3$ 를 이용하여 큐리온도를 상온으로 이동시켰다. 또한 소결온도를 저온화하기 위하여 $BaTiO_3$ 세라믹에 여러가지 산화물을 첨가하여 소결현상을 살펴보았다. 실험결과 첨가제를 넣지 않은 경우 소결온도는 $1350^{\circ}C$의 고온이 필요한 반면, $CuO,B_2O_3$는 $1050^{\circ}C$의 낮은 온도에서도 치밀화와 입도성장이 잘 일어났다. 특히 $B_2$$O_3$ 를 첨가한 경우는 $1250^{\circ}C$이상에서 소결할 때 절연저항이 낮아 유전손실이 큰 문제점을 보였지만, 최대 유전율이 11,000 정도로 높고, 양호한 유전율의 온도변화 특성을 나타내어 우수한 고유전율 소재의 첨가제로 응용될 가능성을 보였다

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.11 no.1
• /
• pp.11-21
• /
• 2013

The Geyoungju Ca-bentonite with dry density of 1.6 g/$cm^3$ has been considered as a standard buffer material for the disposal of high level waste in KAERI disposal system design. But it had relatively lower thermal conductivity compared with other surrounding materials, that was one of key parameters to limit the increase of the disposal density in the disposal system. In this study, various additives were selected and mixed with the Ca-bentonite in different mixing methods in order to increase the thermal conductivity from 0.8 W/mK to 1.0 W/mK. As an additive, CNT (Cabon Nano Tube), graphite, alumina, CuO, and $Fe_2O_3$ were selected, which are chemically stable and have good thermal conductivity. As mixing methods, dry hand-mixer mixing, wet milling and dry ball mill mixing were applied for the mixing. Above all, the ball mill mixing was proved to be most effective since the produced mixture was most homogeneous and showed higher increase in the thermal conductivity. From this study, it was confirmed that the thermal conductivity for the Geyoungju Ca-bentonite could be improved by adding small amount of highly thermal conductive material to 1.0 W/mk. In conclusion, it was believed that the experimental results will be valuable in the disposal system design if the additive effects on the swelling and permeability on the compact bentonite are also approved in further studies.

• Journal of the Korean Chemical Society
• /
• v.40 no.12
• /
• pp.724-732
• /
• 1996

The organic precipitate flotation using Cu(II)-pyrrolidinedithiocarbamate complex as a coprecipitant was studied for the preconcentration and determination of trace Cd, Pb, Bi and Co in several water samples. Experimental conditions such as pH of solution, amounts of Cu(II) and ammonium pyrrolidinedithiocarbamate(APDC), stirring time, the type and amount of surfactant, etc. were optimized for the effective flotation of analytes. After 3.0 mL of 1,000 ${\mu}g/mL$ Cu(II) solution was added to 1.00 L water sample, the pH of the solution was adjusted to 2.5 with HNO3 solution. Trace amounts of analytes were coprecipitated by adding 2.0% APDC solution. And the precipitates were flotated onto the surface of solution with the aid of nitrogen gas and sodium lauryl sulfate. The floats were collected from mother liquor, and filtered through the micropore glass filter by suction. The precipitates were dissolved with 4 mL conc. HNO3, and then diluted to 25.00 mL with deionized water. The analytes were determined by graphite furnace atomic absorption spectrophotometry. This flotation technique was applied to the analysis of some water samples, and the 90 to 120% of recoveries were obtained from the spiked samples, this procedure could be concluded to be simple and applicable for the trace element analysis in various kinds of water.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.107-109
• /
• 2003

This paper was to measure the structure, piezoelectric properties of $0.03Pb(Mg_{0.5}W_{0.5})O_3$ - $0.12Pb(Sb_{0.5}Nb_{0.5})O_3$ - $0.85Pb(Zr_{0.52}Ti_{0.48})O_3$ + $0.5[wt%]MnO_2$ ceramics dropped with additive CuO after manufacturing the specimens with a general method. It is shown that X-ray diffraction pattern variation of lines (211) have tendency to move minutely by addition of additive CuO. According to dropping with Cu, the dielectric constant at 20[$^{\circ}C$] reduced to CuO 3.0[wt%]. In case of sintering at 1050[$^{\circ}C$], dielectric constant was maximum value 623.59 at CuO 1.0[wt%]. Dielectric loss was maximum value 2.7[%] at Cu 2.0[wt%] in case of sintering at 1050[$^{\circ}C$].

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.269-270
• /
• 2009

본 연구는 윤활첨가제에 의한 반도체재료 가공용 다이아몬드 마이크로 블레이드의 절삭성능 향상과 수면연장을 위한 기술개발을 목표로 한다. 마이크로 블레이드와 피 절삭재 사이의 마찰특성의 향상, 그로인한 절삭성능의 향상 등에 미치는 윤활제의 종류와 그 효과를 규명하기 위하여 Cu/Sn계열 다이아몬드 마이크로 블레이드용 결합제에 흑연과 $MoS_2$를 통일한 부피분율로 첨가한 시편을 만들고, 기계적 특성평가와 순간전력소모로 평가하는 절삭성능시험, 블레이드의 마모량 측정을 통한 내구성 실험을 행하였다. 그 결과 기계적 특성과 밀접한 내마모성에 기인한 수명의 관점에서 $MoS_2$를 첨가한 경우가 흑연을 첨가한 경우보다 더 효과적으로 나타났다. 절삭할 때 필요한 순간전력소모로 평가한 절삭성능 평가에서는 동일한 부피분율의 윤활제가 첨가된 경우 차이는 비교적 미미하였다.