• Bulletin of the Korean Chemical Society
• /
• 제21권6호
• /
• pp.588-594
• /
• 2000

Structural changes of an iron phthalocyanine (FePC) monolayer induced by adsorption and externally applied potential on high area carbon surface have been investigated in situ by iron K-edge X-ray absorption fine structure (XAFS) in 0.5 M $H_2S0_4.$ Fine structures shown in the X-ray absorption near edge structure (XANES) for microcrystalline FePC decreased upon adsorption and further diminished under electrochemical conditions. Fe(II)PC(-2) showed a 1s ${\rightarrow}$ 4p transition as poorly resolved shoulder to the main absorption edge rather than a distinct peak and a weak 1s ${\rightarrow}$ 3d transition. The absorption edge position measured at half maximum was shifted from 7121.8 eV for Fe(lI)PC(-2) to 7124.8 eV for $[Fe(III)PC(-2)]^+$ as well as the 1s ${\rightarrow}$ 3d pre-edge peak being slightly enhanced. However, essentially no absorption edge shift was observed by the 1-electron reduction of Fe(Il)PC(-2), indicating that the species formed is $[Fe(II)PC(-3)]^-$. Structural parameters were obtained by analyzing extended X-ray absorption fine structure (EXAFS) oscillations with theoretical phases and amplitudes calculated from FEFF 6.01 using multiple-scattering theory. When applied to the powder FePC, the average iron-to-phthalocyanine nitrogen distance, d(Fe-$N_p$) and the coordination number were found to be 1.933 $\AA$ and 3.2, respectively, and these values are the same, within experimental error, as those reported ( $1.927\AA$ and 4). Virtually no structural changes were found upon adsorption except for the increased Debye-Wailer factor of $0.005\AA^2$ from $0.003\AA^2.$ Oxidation of Fe(II)PC(-2) to $[Fe(III)PC(-2)]^+$ yielded an increased d(Fe-Np) (1 $.98\AA)$ and Debye-Wailer factor $(0.005\AA^2).$ The formation of $[Fe(II)PC(-3)]^-$, however, produced a shorter d(Fe-$N_p$) of $1.91\AA$ the same as that of crystalline FePC within experimental error, and about the same DebyeWaller $factor(0.006\AA^2)$.

• 산업식품공학
• /
• 제14권2호
• /
• pp.118-126
• /
• 2010

The fibrous material fraction as a by-product from the commercial aloe vera gel processing was obtained and freeze dried. The physicochemical characteristics such as the proximate composition, crystalline/surface structures and several physical functionalities including the water holding capacity (WHC), swelling capacity (SW), oil holding capacity (OHC), emulsion/foam properties and viscosity properties of this powdered sample (100 mesh) were investigated and analyzed by comparison with commercial $\alpha$-cellulose as a reference sample. The total dietary fiber content of powdered sample was very high as much as 87.5%, and the insoluble dietary and soluble dietary fiber content ratios were 77.6 and 22.4%, respectively. The FT-IR spectrum of powdered sample showed a typical polysaccharide property and exhibited a x-ray diffraction pattern for cellulose III and IV like structure. SW (8.24${\pm}$0.15 mL/g), WHC(6.40${\pm}$0.19 g water/g solid) and OHC(10.32${\pm}$0.29 g oil/g solid) of freeze dried aloe cellulose were about 3.3, 1.4 and 2 times higher than those of commercial $\alpha$-cellulose, respectively. Aloe cellulose (~2%, w/v) alone had no foam capacity while improved the foam stability of protein solution (1% albumin+0.5% $CaCl_{2}$) by factor of 300%. Emulsion capacity of 2%(w/v) aloe cellulose was about 70% level of 0.5%(w/v) xanthan gum, but its emulsion stability was about 1.2 times higher than that of xanthan gum. Also, aloe cellulose containing CMC (carboxyl methyl cellulose) of 0.3%(w/v) showed a very good dispersity. Aloe cellulose dispersion of above 1%(w/v) exhibited higher pseudoplasticity and concentration dependence than those of $\alpha$-cellulose dispersion, indicating the viscosity properties for new potential usage such as an excellent thickening agent.

• 공업화학
• /
• 제29권6호
• /
• pp.740-745
• /
• 2018

본 연구에서는 비정질 칼슘 포스페이트(ACP) 나노 입자의 합성과 특성 분석을 진행하였다. 염화칼슘(calcium chloride ($CaCl_2$))과 아데노신 인산나트륨(disodium adenosine triphosphate ($Na_2ATP$)) 그리고 피트산 나트륨(sodium phytate) 첨가제를 열수 반응을 통해 상대적으로 단분산된 100 nm 크기 이하의 ACP 나노 입자를 성공적으로 합성하였고 나노 입자의 화학적 조성과 구조를 재료 분석을 통해 확인하였다. 피트산 나트륨 첨가제의 사용을 통해 얻은 ACP 나노 입자는 비정질성을 유지하고 결정성 하이드록시아파타이트(HAP)로의 전환을 방지하는 안정성이 향상되었음을 발견하였다. 본 연구를 통해 발견된 향상된 안정성을 가지는 ACP 나노 입자는 재생 의학 분야에서의 생체 적합 물질로의 응용에 중요한 잠재적 용도가 있을 것이라 사료된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권2호
• /
• pp.122-129
• /
• 2019

콘크리트 구조물에서 균열은 수축, 수화열 및 외부하중 등에 의해 발생하는 불가피한 현상으로, 외부 유해인자를 콘크리트 내부로의 침투를 용이하게 하여 내구성을 크게 감소시킨다. 최근 스스로 균열을 치유하는 자기치유 콘크리트에 대한 연구가 활발히 수행되고 있다. 또한 콘크리트에 발생하는 균열을 제어하여, 그 성능을 극대화하기 위한 자기치유 섬유 보강 콘크리트의 연구가 수행되고 있다. 본 연구에서는 PVA 섬유를 혼입한 자기치유 모르타르를 제작하였다. PVA 섬유 혼입율에 따른 압축강도 및 휨 성능 평가를 수행하였다. 또한, 흡수율 실험을 통해 자기치유 성능평가를 수행하였으며, 시간에 따라 균열 폭의 감소로 흡수되는 수분의 양이 감소하는 것을 확인하였다. 자기치유 생성물 분석을 통해 PVA 섬유 혼입에 의해 탄산칼슘 침전이 더 유리한 것으로 확인되었다.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.82-90
• /
• 2019

In this paper, the effects of different 3D printing conditions including oil lubrication and annealing are observed for their effects on tensile testing. In 3D printing, a press-out extrude filament is rapidly heated and cooled to create internal stress in the printed part. The 3D printing internal stress can be removed using oil-coated filament and annealing. During the oven cooling at an annealing temperature of $106^{\circ}C$, the stress of the specimens with laminated angle $0^{\circ}$ tends to increase by 12.6%, and that of the oil-coated filament printing specimens is increased by 17%. At the annealing temperature of $106^{\circ}C$, the stress of the oil-coated filament printing specimens tends to increase by 35%. In this study, we have found that the oil lubrication and annealing remove the internal stresses and increase the strength of the printed specimens. The oil lubrication and annealing reform the crystalline structures to even out the areas of high and low stress, which creates fewer fragile areas. These results are very useful for the manufacture of 3D printing products with a suitable mechanical strength for applications.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.461-466
• /
• 2018

The effects of Ca/Sr ratio and the sintering temperature on the properties of $(Ca_xSr_{(1-x)})ZrO_3$ (CSZ) ceramics were investigated in this study. CSZ ceramics were prepared using solid-state reaction process, which were sintered in air at temperatures ranging from $1350^{\circ}C$ to $1450^{\circ}C$. Their structures were characterized by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). The change in Ca/Sr ratio significantly affected the crystalline phase and the dielectric properties of the $(Ca_xSr_{(1-x)})ZrO_3$ ceramics. The secondary phase, $Ca_{0.15}Zr_{0.85}O_{1.85}$, was observed and increased correspondingly with the rising of sintering temperatures. In order to understand the effects of secondary phase on the dielectric properties of CSZ ceramics, the $Ca_{0.15}Zr_{0.85}O_{1.85}$ phase was prepared individually using solidstate method. The $Ca_{0.15}Zr_{0.85}O_{1.85}$ ceramics sintered at $1500^{\circ}C$ for 2 hours possessed a dielectric constant (${\varepsilon}_r$) of 21.7, a dielectric loss ($tan{\delta}$) of $49.510^{-4}$ and an Insulation Resistance (IR) of $2.1{\times}10^{10}{\Omega}$. The ($Ca_{0.7}Sr_{0.3})ZrO_3$ ceramics exhibited the best dielectric properties, with a permittivity of 29, a dielectric loss ($tan{\delta}$) of $2.7{\times}10^{-4}$, and an Insulation Resistance (IR) of $2.6{\times}10^{12}{\Omega}$.

• 대한금속재료학회지
• /
• 제56권12호
• /
• pp.900-909
• /
• 2018

A $ZnO/TiO_2$ photocatalyst decorated with PbS quantum dots (QDs) was synthesized to achieve high photocatalytic efficiency for the decomposition of dye in aqueous media. A $TiO_2$ porous layer, as a precursor photocatalyst, was fabricated using micro-arc oxidation, and exhibited irregular porous cells with anatase and rutile crystalline structures. Then, a ZnO-deposited $TiO_2$ catalyst was fabricated using a zinc acetate solution, and PbS QDs were uniformly deposited on the surface of the $ZnO/TiO_2$ photocatalyst using the successive ionic layer adsorption and reaction (SILAR) technique. For the PbS $QDs/ZnO/TiO_2$ photocatalyst, ZnO and PbS nanoparticles are uniformly precipitated on the $TiO_2$ surface. However, the diameters of the PbS particles were very fine, and their shape and distribution were relatively more homogeneous compared to the ZnO particles on the $TiO_2$ surface. The PbS QDs on the $TiO_2$ surface can induce changes in band gap energy due to the quantum confinement effect. The effective band gap of the PbS QDs was calculated to be 1.43 eV. To evaluate their photocatalytic properties, Aniline blue decomposition tests were performed. The presence of ZnO and PbS nanoparticles on the $TiO_2$ catalysts enhanced photoactivity by improving the absorption of visible light. The PbS $QDs/ZnO/TiO_2$ heterojunction photocatalyst showed a higher Aniline blue decomposition rate and photocatalytic activity, due to the quantum size effect of the PbS nanoparticles, and the more efficient transport of charge carriers.

• 대한금속재료학회지
• /
• 제46권3호
• /
• pp.159-168
• /
• 2008

Thermally-evaporated 10 nm-Ni/1 nm-Ru/(30 nm or 70 nm-poly)Si structures were fabricated in order to investigate the thermal stability of Ru-inserted nickel monosilicide. The silicide samples underwent rapid thermal anne aling at $300{\sim}1,100^{\circ}C$ for 40 seconds. Silicides suitable for the salicide process were formed on the top of the single crystal and polycrystalline silicon substrates mimicking actives and gates. The sheet resistance was measured using a four-point probe. High resolution X-ray diffraction and Auger depth profiling were used for phase and chemical composition analysis, respectively. Transmission electron microscope and scanning probe microscope(SPM) were used to determine the cross-sectional structure and surface roughness. The silicide, which formed on single crystal silicon and 30 nm polysilicon substrate, could defer the transformation of $Ni_2Si $i and $NiSi_2 $, and was stable at temperatures up to $1,100^{\circ}C$ and $1,100^{\circ}C$, respectively. Regarding microstructure, the nano-size NiSi preferred phase was observed on single crystalline Si substrate, and agglomerate phase was shown on 30 nm-thick polycrystalline Si substrate, respectively. The silicide, formed on 70 nm polysilicon substrate, showed high resistance at temperatures >$700^{\circ}C$ caused by mixed microstructure. Through SPM analysis, we confirmed that the surface roughness increased abruptly on single crystal Si substrate while not changed on polycrystalline substrate. The Ru-inserted nickel monosilicide could maintain a low resistance in wide temperature range and is considered suitable for the nano-thick silicide process.

• 한국결정성장학회지
• /
• 제31권6호
• /
• pp.233-239
• /
• 2021

본 연구에서는 산화갈륨의 방열 특성 향상을 위해 산화갈륨/다이아몬드 이종 박막 성장을 진행하였다. 먼저, 핫필라멘트 화학기상증착법을 이용하여 다결정 다이아몬드를 증착시킨 후, 미스트 화학기상증착법을 통해 450~600℃ 사이의 온도구간에서 산화갈륨 박막을 성장시켰다. 열처리 전후 비교를 통해 500℃에서 산화갈륨/다이아몬드 계면 분리 현상이 발생함을 확인하였다. 이는 비정질과 결정질이 혼재된 산화갈륨 박막이 성장된 후, 냉각 과정에서 열팽창계수의 차이로 인해 계면이 분리된 것으로 판단하였다. 따라서, 본 연구를 통한 산화갈륨/다이아몬드 계면의 물리적 안정성을 통해 산화갈륨의 열물성 보완및 고전력 반도체로의 활용이 기대된다.

• 접착 및 계면
• /
• 제24권1호
• /
• pp.36-40
• /
• 2023

반데르발스 물질이란 층간 결합이 약한 반데르발스 결합으로 이루어진 이차원 층상구조를 지닌 물질을 의미하며, 이러한 반데르발스 이차원 소재를 이용한 이종접합 구조 연구는 그래핀이 발견된 이후 꾸준히 연구되고 있다. 본 논문에서는 대기압 화학기상증착법을 통해 성장된 단층 단결정 MoSe₂를 기반으로하는 반데르발스 이종접합 트랜지스터 소자에 대해 보고한다. 최적화된 공정조건에서 성장된 MoSe₂는 원자수준의 결함이 존재하지 않는 것을 밝혔으며, 이를 이용한 트랜지스터 소자 또한 우수한 특성을 보인다는 것을 밝혀내었다.