• Design & Manufacturing
• /
• v.2 no.4
• /
• pp.54-61
• /
• 2008

Warpage, which is one of the molding trouble, acts as possible factor which results in defect in assembly. In this study, a mold was designed to produce specimens with rib parallel to flow direction, specimens with rib perpendicular to flow direction and specimens without rib. This work researched change of warpage according to injection molding condition such as injection pressure, packing pressure, packing time, resin temperature, mold temperature in non-crystalline resins(PC, ABS), crystalline resins(PP, PA66), and 30% glass fiber reinforced-resins(PC, ABS, PP, PA66).Specimens with rib and Crystalline resins show more warpage than specimens without rib and non-crystalline resins, respectively. Glass fiber reinforced-resins and specimens with rib parallel to flow direction show smaller warpage than conventional resins and specimens with rib perpendicular to flow, respectively. Specimens with rib and specimens without rib show reduced warpage as packing time increases. In addition, warpage increase as resin temperature increases. It is found that CAE shows similar tendency with experiment as packing time, resin temperature. when the rib is caused, warpage will reduce and prevent the transformation. product of a irregular form occurs warpage. In the study It'll be basic data that product occurs warpage, preferablity.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.1
• /
• pp.1-7
• /
• 2004

This paper describes the carbonization characteristics of a phenolic resin deteriorated by tracking under the environment of a fire. In the experiment, a liquids droplet of 1[％] NaCl was dripped on the phenolic resin to cause a tracking with 110[V], 220[V] voltages applied. It can be addressed from the experimental results that when an insulator is carbonized by an external fire, its structure is amorphous. If an insulator is carbonized by electrical cause, on the other hand, its structure would be crystalline. In order to observe the surface change of the phenolic resin, the tracking process was analyzed by using SEM. In the case that the materials are carbonized under heat or fire, the exothermic peak appears around 500[$^{\circ}C$]. This is one of the important factors to determine the cause of fires. As a result of DTA, the exothermic peaks of an untreated sample showed at 333.4[$^{\circ}C$], 495.7[$^{\circ}C$] but those of a sample deteriorated by tracking appeared at 430.6[$^{\circ}C$], 457.6[$^{\circ}C$] in a voltage of 110[V], and at 456.2[$^{\circ}C$], 619.7[$^{\circ}C$] in a voltage of 220[V]. It is possible, therefore, to distinguish a virgin sample from carbonized samples(graphite) by the exothermic peak.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.4
• /
• pp.797-810
• /
• 1998

The purpose of this study was to develop a new way of delivery system of chlorhexidine using self-curing acrylic resin. Different preparations of chlorhexidine, such as chlorhexidine varnish($Chlorzoin^{(R)}$) and chlorhexidine diacetate crystalline, were mixed into self-curing acrylic resin with different methods. Every resin plate was made and was immersed in 100ml of distilled water individually, and kept in an incubator at $37^{\circ}C$. Solution(0.8ml) was collected from the each container at every 24 hours, and the amount of released chlorhexidine in the solution was measured in an ultraviolet spectrophotometer at 255nm. Flexural strength of all of the resin plates in the Experiment 2-A and 2-B were measured using Instron at the end of the experimental periods. The results were as follows: 1. It was found that chlorhexidine was released from the experimental groups in the Experiment 1, 2-A, and 2-B. And the release of chlorhexidine from all of the experimental groups showed a pattern of sustained-release preparation. 2. It seemed likely that a condition of "dryness" reduced a release of chlorhexidine from the chlorhexidine varnish. 3. It may be stated that a method of "chlorhexidine diacetate mix" with the polymer be more efficient than a method of "Chlorzoin mix" with the monomer. 4. Although it was evident that a flexural strength of the acrylic resin plates be reduced by a mix of either Chlorzoin or chlorhexidine diacetate crystalline, it seemed likely that the resin plates except Group 4 and 5 in the Experiment 2-B may be usable in the clinical situation.

• The korean journal of orthodontics
• /
• v.29 no.1 s.72
• /
• pp.107-112
• /
• 1999

As increasing number of adult patients, the esthetic orthodontic appliances are needed. They are tooth-colored or translucent ceramic and resin brackets. Although ceramic and resin bracket have good esthetics, there are some disadvantage such as frictions. Recently, metal-reinforced resin bracket(MRBB) were introduced. The purpose of this study is to find frictional force of MRRB, ceramic bracket and resin brackets. There is few study in frictional force about metal reinforced resin bracket(MRRB). This study used 4 orthodontic wire(.016 S-S, .0l6X.022 S-S, .016 $TMA^{\circledR}$, .0l7X.025 $TMA^{\circledR}$ and 5 brackets(one metal bracket, one ceramic bracket, one resin bracket, two MRRB). The following result is obtained using metal bracket(Ormco.Co., U.S.A), ceramic brackets($Crystalline^{\circledR}$), resin bracket( Clear Medium $Siamase^{\circledR}$). Following conclusions are obtained. 1. Ceramic and resin bracket have significantly more frictional forces than metal reinforced resin bracket and metal bracket. 2. There is no significant difference in frictional force according to the slot types of metal - reinforced resin brackets. 3. There is no significant difference in frictional force between metal reinforced resin bracket and metal bracket. 4.. Frictional force is decreased in S-S wire than TMA wire.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.12-16
• /
• 2019

For optimal injection molding, various molding conditions should be combined well. Therefore, engineers should be thoroughly familiar with mold design, fabrication, and injection molding. The choice of resin among the various molding conditions is closely related to the productivity of the molded part and the deformation after molding, so the engineer must select the appropriate resin. Engineers work on the basis of data provided by resin manufacturers during molding. However, in actual molding work, it is necessary to apply values slightly different from those provided to obtain molded articles of desired performance. In this study, various deformations of molded products were compared with respect to crystalline resin and amorphous resin when molded according to the data provided by the resin maker and molded at the changed values at the work site.

• Carbon letters
• /
• v.1 no.1
• /
• pp.1-5
• /
• 2000

The effect of surface free energy on the positive temperature coefficient (PTC) of carbon black/thermoplastic resin composites was investigated. The thermoplastic resins such as EVA, LDPE, LLDPE and HDPE were used with the addition of 30 wt.% of the carbon black. The surface free energy of the composites was studied in the context of two-liquid contact angle measurements, i.e., deionized water and diiodomethane. It was observed that the resistivity on PTC composites Was greatly increased near the crystalline melting temperature, due to the thermal expansion of polymeric matrix. From the experimental results, it was proposed that the decrease of surface free energy induced by interactions between carbon black surfaces and polymer chains is an important factor to the fabrication of a PTC composite made of carbon black and polymeric matrix.

• Microbiology and Biotechnology Letters
• /
• v.7 no.3
• /
• pp.127-133
• /
• 1979

By the treatment of several mutagens, a number of 5'-guanylic acid producing mutants from 5'-xan-thylic acid were obtained from Brevibacterium ammoniagenes ATCC 6871. The indispensensable genetic-characters of the mutants were adenine requirement, lack of GMP-reductase and mutation to adenosine resistance from adenosine sensitiveness. Main product from 5'-xanthylic acirl by strain BA-17-2 was 5'-guanulic acid, and was isolated in a crystalline form by the use of anion exchange resin, Duolite 102 D. The isolated crystalline was identified as 5'-guanylic acid by means of paper chromatography, ultrav-iolet absorption spectra, and infrared absorption spectrum.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.44-51
• /
• 2020

The basic catalyst 1-benzyl-3-methyl-imidazolium hexafluoroantimonate (BMH) was synthesized and analyzed by FT-IR and ¹H-NMR. A crystalized biphenyl-based epoxy was synthesized by using tetramethyl biphenol (TMBP) and epichlorohdrine. In order to consider the curing tendency of the synthesized BMH, the mass ratio was changed to 0.5, 1.0, 2.0 wt.% under heated conditions and the curing tendency was analyzed by differential scanning calorimeter (DSC). As a result, the BMH catalyst showed a fast curing result in the stepwise heating pr℃ess of the biphenol-A epoxy and the cationic polymer. From these results, the BMH catalyst showed excellent thermal stability as a potential heat curing catalyst. In addition, we considered the application possibility of epoxy molding compound (EMC) which required a skeleton structure and a high heat resistance because the synthesized biphenyl epoxy had a characteristic of rapidly lowering viscosity at a constant temperature and a rigid skeleton structure of biphenol. As a result, it was confirmed that the TMBP-based epoxy developed in this study was composed of a crystalline structure, and a curing reaction was observed with a Novolac resin at a high temperature. In the presence of a catalyst, a curing reaction was observed around 150 ℃ and thus TMBP-based epoxy was successfully applied as a raw material of EMC.

• Journal of the Korean Ceramic Society
• /
• v.22 no.1
• /
• pp.35-39
• /
• 1985

Synthetic mica $NaMg_{2.5}(Si_4O_{10})F_2 (Na-TSM)$ was treated with HCl solution and H-type exchange resin to investigate the chemical stability and the ion exchange by measuring the dissolution of chemical components and the exchanged $H^+$ ion. The replacement of $Na^+$ ion occurred in contact with HCl solution and H-type ion exchange resin at the surface of Na-TSM particles reached $Na^+$ ions at maximum value of 70~80%. $Mg^{2+}$ ion of octahedral layer became to dissolve from the pH2 solution and th amount of it dissolved in-creased almost proportional to $H^+$ ion concentration from around 0.02N $H^+$ ion equilibrium concentration. The crystalline structure of Na-TSM was destructed by dissolution of Mg2+ ion in cncentrated hydrochloric acid solution and resulted silica gel precipitation.

• Elastomers and Composites
• /
• v.26 no.4
• /
• pp.296-303
• /
• 1991

Surface of crystalline silica was sequentially reacted with silane(A 187), liquid $rubber(CTBN{\times}8)$, and vinyl monomer(GMA) in existence of TEA(triethylamine) or BPO(benzoyl peroxide). It was mixed with epoxy resin at a ratio $0{\times}60%$ (vol. % ) of total component. For mixtures, viscous properties were investigated experimentally. 1) Coating ratio depended on pH of mixture and quantity of catalyst. 2) Treated silica represented lower viscosity than untreated. 3) Thixotropic index represented best at silica_content $15{\sim}23%$ and showed more large deviation over $120^{\circ}C$. 4) Relative viscosity followed kernel's at $0{\times}10%$ of silica content and get out of Mooney's at more than 15%.