• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.1-5
• /
• 1993

In the country, due to short comings of natural aggregates of good quality, it is common to use crushed stones. However, the investigation has not been done on the chemical reaction of crushed stones. This study tested and analyzed the aggregate chemical reaction by petrographic examination(ASTM C 295) for the test aggregates which had been tested by chemical method(ASTM C 289) in the first year. As a result, most of test aggregates didn't show any reaction but many have common deleterious mineral. Therefore, there exists the possibility of chemical reaction in petrogrphic point of view

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.233-238
• /
• 1998

For substitution for crushed sand, high strength aggregate for cement and concrete using coal ash as a main material was prepared and then compared its physical properties with those of crushed sand. Effect of mix proportion change of raw materials on the property of aggregate was checked. On the basis of these experimental results we are going to comprehend the reutilization of coal ash and utilize a basic data for judging possibility the substitution of crushed sand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.661-664
• /
• 1998

In this paper, the properties of inter-lacking block by the kind of aggregate and fineness modulus are investigated. According to the experimental results, compressive strength and flexural strength increase and absorption ratio decrease with larger fineness modulus in the range of 2.15~4.20. Flexural strength with river sand is higher than that with crushed sand by about 19%, compressive strength with river sand, that with crushed sand by about 11% and absorption ratio with river sand is smaller than that with crushed sand by abort 2%.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.04a
• /
• pp.16-19
• /
• 1990

The effect of superplasticizers on the fluidity performance in fresh concrete and physical properties in hardened concrete have been analyzed and investigated under mix proportions of water cement ratio of 0.4, 0.6, crushed stone aggregates, and addition rates of superplasticizers of 0.0, 0.5, 1.0 and 1.5 in the practical range. It is the aim of this study to provide the fundamental data on the workability improvement and engineering properties of crushed stone concrete using superplasticizers comparing with conventional concrete for the practical use and research data accumulation of superplastized concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.97-102
• /
• 1993

In the country, due to short comings of natural aggregates of good quality, it is common to use crushed stones. However, the investigation has not been done on the chemical reaction of crushed stones. This study tested and analyzed the aggregate chemical reaction by Petrographic Examination(ASTM C 295),Chemical Metho(ASTM C 289) and Mortar-Bar Method (ASTM C 227). As a result, most of test aggregates didn't show any reaction but many have common deleterious mineral. Therefore, there exists the possibility of chemical reaction in petrographic point of view.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.10a
• /
• pp.50-53
• /
• 1992

The damages due to alkali-aggregate reaction between the reactive silicia constituents of the aggregate and the alkalies in cement have been frequently reported since 1923 in America . Recently alkali-aggregate reaction, especially alkali-silica reaction, can be found all over the area using crushed stones. The first research, in 1990, was performed to identify the alkali-silica reactivity of 18 sets of crushed stones used in domestic ready-mixed concrete plant as coarse aggregates by 4 petrollgical, chemical and mortar bar method, And the study was continued with 10 sets of crushed stones in this research. It was found that all the aggregates used in this study are innocuous at alkali-silica reaction.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.941-946
• /
• 2001

In this study, three kinds of fine aggregate (river sand, sea sand, crushed sand) were used and four different s/a (38%, 40%, 42%, 45%) were applied separately to this experimental for get the conclusion written below. Regardless of kinds of fine aggregate and casting-curing condition, maximum unit weight is seen at 40% of s/a and also to be seen in case of crushed sand. It's for that specific gravity of crushed sand is bigger comparatively than river sand and sea snad's one. Compressive strength is measured river sand, crushed sand, sea sand by order of size ; Regardless of variation of s/3, casting-curing condition and age. Compressive strength recorded maximum when s/a is 42% whatever sort of fine aggregate are. As the result, according to references, the optimum s/a of underwater antiwashout concrete is 40% but in this study, from compressive strength of view, the optimum s/a of underwater antiwashout concrete is 42%.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.89-92
• /
• 2005

This study investigates influence of particle properties of crushed sand on the duality of concrete. The test shows that an increase of fineness modulus(FM) resulted in high slump and air contents, while compressive strength decreased due to decreased adhesion with reduction of surface area. As grain shape become rounder, the slump of concrete increased, due to reduction of internal friction, and increased air contents. The reduction of adhesion by abrasion of surface declined compressive strength during the process of manufacturing crushed sand. Increase of powder contents decreased slump and it also decreased air contents due to the effect of filling air void. In addition. using powder contents increased compressive strength, but could not find any difference of bleeding and tensile strength with particle properties.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.73-78
• /
• 2001

Portland cement concrete is made with coarse aggregate, fine aggregate, portland cement, water and, in some cases, selected chemical admixtures such as air-entraining agents, water reducer, superplasticizer, and so on, and mineral admixtures such as fly ash, silica fume, slags, etc. Typically, in the concrete, the coarse aggregate and fine aggregate will occupy approximately 80 percent of the total volume of the final mix. Therefore, the coarse and fine aggregates affect to the properties of the portland cement concrete. As the natural sands are drained, it is necessary and economical to utilize crushed sands(manufactured fine aggregate). It is reported that crushed sands differ from natural sands in gradation, particle shape and texture, and the micro fines in the crushed sands affect to the quality of the portland cement concrete. Therefore, the purpose of this paper is to investigate the characteristics of fresh and hardened concrete with high content of micro fines. This study provides firm data for the use of crushed sands with higher micro fines.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.317-322
• /
• 2001

This paper investigates the influence of fine aggregates on bleeding of concrete. According to test results, as water content decreases, crushed sand content increases, fluidity shows decline tendency. As for aggregates kinds, concrete using sea sand shows most fluidity loss among the tested results. Compressive strength gains highly when crushed sand is used. As for bleeding of concrete, bleeding shows decline tendency because of increasing in powder content and filling effect of voids. Bleeding amount is in a decreasing order of magnitude for concretes made with the following aggregates: sea sand, river sand, and crushed sand. Accordingly, crushed sand mixed with river sand and sea sand with certain proportion enable to reduce bleeding and enhance strength.