Recently, a nursery mat made from rock wool has realized transplanting of the younger seedlings with the ordinary transplanting machines for Chibyo and Chubyo(3 and 4~5 leaved seedling, respectively). The seedlings defined as the 'Nyubyo' or 'Nursling seedlings' became possible to achieve economic profits from the reduction in both working time and costs. It being widely noticed as a strategy to solve the difficulties in current rice cultivation. The nursling seedlings are 1.4 to 2.5 leaves and height at 4.5 to 7cm, grown 4 to 7 days after seeding. They maintain still up to 50 to 80% of their nutrients in the endosperm, and can grow by using only their own nutrients for a certain period of time after transplanting. Nursling seedlings take 2 days in the nursery chamber at 32$^{\circ}C$ after seeding, and 2 days in the greening house at $25^{\circ}C$. This is only 4 days, all together, to make the nursling seedlings of 1.5 leaves which are ready for transplanting. Watering is only needed once at the sowing time. It only takes 1 or 2 waterings even to raise a seedlings for a period of 7 days. The number of nursery boxes can be reduced because it is possible to sow more densely(220 to 240g per box), thus it only needs seedlings of 15 to 16 boxes per 10 a which leads to a reduction in facilities and space needed. Temperature during the nursery period can be artificially adjusted more precisely which may lead to the prevention of temperature stress. The nursling seedlings can root rapid by because the crown roots from the coleoptile node begin to emerge immediately after transplanting. They show strong resistance to low temperature (12$^{\circ}C$) and deep-planting. There is no danger in the rooting of the seedlings even if half of their height is buried into the soil. Moreover, it can root at a rate of up to 65 to 80% even if the full height of the seedlings is buried. They show also strong resistance to submergence (10~15cm). The nursling seedlings tend to grow by producing tillers from lower nodes. It is therefore, necessary to control to keep the proper numbers of tillers per unit area. They have no fear in the delay of heading and their yield components can be so well balanced that the same level of yield was achieved with the nursling seedlings compared to that with Chibyo. It was further suggested that if the surplus tillers can be avoided by such cultivation practices, the number of grain per panicle can be kept greater and higher yield can be realized. Practical experiments with the nursling seedlings conducted in 1989 and 1990 by farmers in various areas showed exciting results. The nursling seedlings will become widely spread, or at least occupy an important position in Japanese and also in Korean rice cultivation techniques.tivation techniques.
Korean Journal of Agricultural and Forest Meteorology
/
v.14
no.4
/
pp.222-228
/
2012
This study was conducted to determine the natural succession process after forest fire by comparing height, relative growth rates in height (RGH), and tree density of pine seedlings with different fire severity. In the area damaged by surface fire, tree density was highest during the first 5 years after fire. However, in the area damaged by crown fire, tree density rapidly increased during first 5 years after fire. Pine seedlings were found only on the place with ridges, barren soil, and the aspect of north. Annual height growth of pine seedlings was decreased with time in all study sites. The empty space in pine stands gradually decreased by the invasion of Quercus species. The forest fire altered the pine forest into oak forest rapidly. In contrast, pine seedlings invaded steadily on the oak forest in the rocky area or the area with ridges.
Kim, Eun-Sook;Kim, Kyoung-Min;Lee, Jung-Bin;Lee, Seung-Ho;Kim, Chong-Chan
Journal of Korean Society of Forest Science
/
v.100
no.3
/
pp.455-465
/
2011
In order to assess and mitigate climate change, the role of forest biomass as carbon sink has to be understood spatially and quantitatively. Since existing forest statistics can not provide spatial information about forest resources, it is needed to predict spatial distribution of forest biomass under an alternative scheme. This study focuses on developing an upscaling method that expands forest variables from plot to landscape scale to estimate spatially explicit aboveground biomass(AGB). For this, forest stand variables were extracted from National Forest Inventory(NFI) data and used to develop AGB regression models by tree species. Dominant/codominant height and crown density were used as explanatory variables of AGB regression models. Spatial distribution of AGB could be estimated using AGB models, forest type map and the stand height map that was developed by forest type map and height regression models. Finally, it was estimated that total amount of forest AGB in Danyang was 6,606,324 ton. This estimate was within standard error of AGB statistics calculated by sample-based estimator, which was 6,518,178 ton. This AGB upscaling method can provide the means that can easily estimate biomass in large area. But because forest type map used as base map was produced using categorical data, this method has limits to improve a precision of AGB map.
Background: Most of the biomass equations were developed using sample trees collected mainly from pan-tropical and tropical regions that may over- or underestimate biomass. Site-specific models would improve the accuracy of the biomass estimates and enhance the country's measurement, reporting, and verification activities. The aim of the study is to develop site-specific biomass estimation models and validate and evaluate the existing generic models developed for pan-tropical forest and newly developed allometric models. Total of 140 trees was harvested from each diameter class biomass model development. Data was analyzed using SAS procedures. All relevant statistical tests (normality, multicollinearity, and heteroscedasticity) were performed. Data was transformed to logarithmic functions and multiple linear regression techniques were used to develop model to estimate aboveground biomass (AGB). The root mean square error (RMSE) was used for measuring model bias, precision, and accuracy. The coefficient of determination (R2 and adjusted [adj]-R2), the Akaike Information Criterion (AIC) and the Schwarz Bayesian information Criterion was employed to select most appropriate models. Results: For the general total AGB models, adj-R2 ranged from 0.71 to 0.85, and model 9 with diameter at stump height at 10 cm (DSH10), ρ and crown width (CW) as predictor variables, performed best according to RMSE and AIC. For the merchantable stem models, adj-R2 varied from 0.73 to 0.82, and model 8) with combination of ρ, diameter at breast height and height (H), CW and DSH10 as predictor variables, was best in terms of RMSE and AIC. The results showed that a best-fit model for above-ground biomass of tree components was developed. AGBStem = exp {-1.8296 + 0.4814 natural logarithm (Ln) (ρD2H) + 0.1751 Ln (CW) + 0.4059 Ln (DSH30)} AGBBranch = exp {-131.6 + 15.0013 Ln (ρD2H) + 13.176 Ln (CW) + 21.8506 Ln (DSH30)} AGBFoliage = exp {-0.9496 + 0.5282 Ln (DSH30) + 2.3492 Ln (ρ) + 0.4286 Ln (CW)} AGBTotal = exp {-1.8245 + 1.4358 Ln (DSH30) + 1.9921 Ln (ρ) + 0.6154 Ln (CW)} Conclusions: The results demonstrated that the development of local models derived from an appropriate sample of representative species can greatly improve the estimation of total AGB.
Kim, TaeHyeon;Kim, Jong-Eun;Lee, Ah-Reum;Park, Young-Bum
The Journal of Korean Academy of Prosthodontics
/
v.54
no.3
/
pp.234-238
/
2016
Purpose: Increasing use of computer aided design-computer aided manufacturing (CAD-CAM) system and number of design software made design of restoration easy and quick. Outcome of restoration has been dependent on dental technician's wax up proficiency, dentists can design restoration for themselves now. This study aims to investigate the outcome of restoration designs, according to handling skill of CAD-CAM design tool. Materials and methods: A patient's mandibular right 1st molar was prepared. After taking impression, stone model was made, scanned the stone model with 3 shape intra-oral scanner, stereolithography (STL) file was extracted. With 3shape dental designer, one dental technician with more than 5 years work experience (designer 0) and three dental technicians with less than 2years work experience (designer 1, 2, 3-group DT) and 4 1st year residents (designer 4, 5, 6, 7-group RT) designed gold crown on the same STL file. Designed crown's MD (mesio-distal) and BL (bucco-lingual) diameter, height of crown, inter-cuspal distance, number of occlusal contact points were compared. Statistical analysis was carried out, test of normality within each group, using independent t-test. Number of contact points were compared, using Wilcoxon signed-rank test. Results: There was no significant difference between group DT and group RT. Number of contact points also resulted in no significant difference. Conclusion: The outcome of each designed crowns showed no statistical differences, in values which can be expressed as numbers. Subjective factors were different. With increasing proficiency in handling designing software, fabrication of restorations according to each designer's occlusal concept can be made easy.
Six natural populations of Pinus densiflora S. et Z. as shown in the location map (Flg 1) were studied during 1978. The numerial pouplation codes, 13 to 18. The results of populations 1 to 12 were reported in previous papers. Following the study methods described before, 20 trees were sampled from each population and morpological characteristics such as stem forms, branching habit needle and wood properties investigated. The results are summerized as follows; 1. The mean stand ages were ranged from 36 to 97 of years. The growth performances of trees of population 14. 15 and 18 was similar, but 13, 16, and 17 seemed to be inferior more or less. 2. The ratios of clear bole length were 0.70 in population 18 as the highest but 0.28 for population 16 as the lowest. 3. The population 17 was considered to be a stand of the coarser branching habit having the crown index (The maximum crown diameter/the crown height) 158 though the branching angles were almost horizontal. 4. The differences were observed in the clear bole length ratios and crown-indices between population as shown In Fig. 3 and 4. 5. As to the serration density, number of stomata row and resin duct; the significant differences exist between individual trees within population and also between populations. 6. Population 18 shown resin duct index 0.119 as the maximum. 7. The patterns of diameter growth, based on the width of 10-year-ring segment unit(for example, the 1st segment denotes the with between pith center and 10th year ring and the 2nd one is from 11th to 20th ring and so on.), were alike among populations as shown in Fig 9. 8. Significant differences between population in mean summer wood percentage as well as in wood specific gravity was observed. The values of wood specific gravity were increased with the increase of ages in population 14, 18 however vice versa in population 13, 15, and 17. 9. The fiber length was mereased with the increased of age but no differences between populations as shown in Fig. 12.
Journal of Korean Tunnelling and Underground Space Association
/
v.19
no.5
/
pp.761-778
/
2017
The need of the underground space for the infrastructures in urban area is increasing, and especially the demand for shallow tunnels increased drastically. It is very important that the shallow tunnel in the urban area should fulfill not only its own safety conditions but also the safety condition for the adjacent structures and the surrounding sub-structure. Most of the studies on the behavior of shallow tunnels concentrated only on their behaviors due to the local deformation of the tunnel, such as tunnel crown or tunnel sidewall. However, few studies have been performed for the behavior of the shallow tunnel due to the deformation of the entire tunnel. Therefore, in this study the behavior of the surrounding ground and the stability caused by deformation of the whole tunnel were studied. For that purpose, model tests were performed for the various ground surface slopes and the cover depth of the tunnel. The model tunnel (width 300 mm, height 200 mm) could be simulationally deformed in the vertical and horizontal direction. The model ground was built by using carbon rods of three types (4 mm, 6 mm, 8 mm), in various surface slopes and cover depth of the tunnel. The subsidence of ground surface, the load on the tunnel crown and the sidewall, and the transferred load near tunnel were measured. As results, the ground surface subsided above the tunnel, and its amount decreased as the distance from the tunnel increased. The influence of a tunnel ceased in a certain distance from the tunnel. At the inclined ground surface, the wider subsidence has been occurred. The loads on the crown and the sidewall were clearly visible, but there was no effect of the surface slope at a certain depth. The load transfer on the adjacent ground was larger when the cover depth (on the horizontal surface) was lager. The higher the level (on the inclined surface), the wider and smaller it appeared. On the shallow tunnel under inclined surface, the transfer of the ambient load on the tunnel sidewall (low side) was clearly visible.
Seo, Min-Seock;Shon, Won-Jun;Lee, Woo-Cheol;Yoo, Hyun-Mi;Cho, Byeong-Hoon;Baek, Seung-Ho
Restorative Dentistry and Endodontics
/
v.34
no.4
/
pp.324-332
/
2009
The purpose of this study was to investigate the effect of rigidity of post core systems on stress distribution by the theoretical technique, finite element stress-analysis method. Three-dimensional finite element models simulating an endodontically treated maxillary central incisor restored with a zirconia ceramic crown were prepared and 1.5 mm ferrule height was provided. Each model contained cortical bone, trabecular bone, periodontal ligament, 4 mm apical root canal filling, and post-and-core. Six combinations of three parallel type post (zirconia ceramic, glass fiber, and stainless steel) and two core (Paracore and Tetric ceram) materials were evaluated, respectively. A 50 N static occlusal load was applied to the palatal surface of the crown with a $60^{\circ}$angle to the long axis of the tooth. The differences in stress transfer characteristics of the models were analyzed. von Mises stresses were chosen for presentation of results and maximum displacement and hydrostatic pressure were also calculated. An increase of the elastic modulus of the post material increased the stress, but shifted the maximum stress location from the dentin surface to the post material. Buccal side of cervical region (junction of core and crown) of the glass fiber post restored tooth was subjected to the highest stress concentration. Maximum von Mises stress in the remaining radicular tooth structure for low elastic modulus resin core (29.21 MPa) was slightly higher than that for high elastic modulus resin core (29.14 MPa) in case of glass fiber post. Maximum displacement of glass fiber post restored tooth was higher than that of zirconia ceramic or stainless steel post restored tooth.
Kim, Sodam;Moon, Ae-Ra;An, Jong-Bin;Jung, Ji-Young;Park, Wan-Geun;Son, Sungwon
Korean Journal of Environment and Ecology
/
v.34
no.1
/
pp.18-26
/
2020
Echinosophora koreensis (Nakai) Nakai an endemic plant with limited distribution in some parts of the Korean Peninsula, is designated as "Endangered" species on the IUCN Red List. The species is under the threat of deterioration in nature due to various environmental changes causing loss of natural habitats. We investigated the distribution pattern and population structure of E. koreensis to serve as a basic reference for identifying the dynamics and persistence of natural populations of this species in the future. To determine the characteristics of the E. koreensis population, we laid two to three large plots sized 20m×30m on the ridgeline as the reference in Yanggu, Chuncheon, and Hongcheon and laid four to seven small quadrats sized 1m×1m on the transect. A total of 530 plots were laid, 10 each at 2m interval, to measure the number of the stems, the number of fruiting, height, and other factors. The collected distribution information was compared with the existing IUCN assessed categories by applying IUCN Red List ver 3.1 Criteria B. The average population density of the three surveyed areas was 3.47 stem/㎡; the density of each area was 3.95 stems/㎡ in Yanggu, 3.37 stems/㎡ in Chuncheon, and 2.87 stems/㎡ in Hongcheon. The number of fruiting per stem was 0.0038, indicating only 7 fruits out of 1,837 stems and that vegetative reproduction is likely to be more dominant than sexual reproduction. The distribution tendency of population density in the small plots in three surveyed areas showed that the density of E. koreensis tended to decrease toward the center of the forest with low crown openness and around the mountain ridge with high crown openness. It indicated that the quantity of light could be a very important factor for the growth of individuals of this species. The analysis of the heights of individuals present in the surveyed plots showed a range of 2.3 ~ 68.5cm and an average of 20.1cm. An analysis on the stage-structure of the E. koreensis population based on the sieve height found that the appearance frequency decreased with increasing height above 15 ~ 20cm and that the percentage of individuals lower than 10cm, which were presumed to be seedlings, was severely low, indicating a necessity of study on the population sustainability based on the monitored data. The occupied area calculated with the collected species distribution information was 200㎢, indicating the EN category according to the IUCN Red List Reference B.
In the present paper I described the results of the observations made on the visual characteristics such as the annual ring width and summerwood percentage of Pinus koraiensis Sieb. et Zucc. grown at out university forest. The results of the study are as follows: Characteristics of annual ring width and summerwood percentage 1. The range of dispersion of annual ring width and summerwood percentage are respectively 0.5-6.5mm and 5-50% on the normal wood and its arithmetic mean values are each 3.0mm and 24% on all sample trees. 2. The values of annual ring width of heart wood are larger than that of sapwood but on the contrary the values of summerwood percentage of heartwood are smaller than that of sapwood. On the other hand variations of these values are distingushed on the heartwood. 3. The values of annual ring width due to the parts of stem with crown. with clear length and at bottom showed that the largest values are given at the parts of stem with crown. But on the contrary the summerwood percentage values are largest at the parts of stem at bottom on all sample trees. 4. The values of annual ring width and summerwood percentage depending on the stand sides are not obvious. Horizontal and vertical variations of annual ring width and summerwood percentage 5. It was recognized that horizontal (radial direction) variations of annual ring width and summerwood percentage indicated two different patterns (the region of large fluctuation and that of small fluctuation) in a tree stem. These boundaries are seemed to appear at the parts of 12-15 annual rings from pith. 6. According to the increase of height in tree the values of annual ring width increase but the values of summerwood percentage gradually decrease. 7. But vertical variations of annual ring width and summerwood percentage on the sapwood are divided into two different parts (region of increased or decreased upwards and that of remained constant in successive height) in a tree stem and these limits are seemed to appear at the 7m of height in trees. Relations between annual ring width and summerwood percentage 8. The modes of summerwood percentage related with annual ring width are seemed to appear almost in the definite range (10-25%). 9. The relations between annual ring width and summerwood percentage show a highly negatine correlation on all sample trees.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.