• Journal of Pharmaceutical Investigation
• /
• v.32 no.1
• /
• pp.1-6
• /
• 2002

The mucoadhesive characteristics of [P(AA-co-PEGMM)] films by estimating the glass transition temperature $(T_g)$, analyzing surface energy and studying FT-IR was previously reported. In this study, the possibility of buccal mucoadhesive dosage form of [P(AA-co-PEGMM)] films by mucoadhesive force measurements and dissolution tests were also investigated. Mucoadhesiveness of [P(AA-co-PEGMM)] films was compared with cr-PAA and cr-PEGMM films crosslinked with 3% ethyleneglycol dimethacrylate (EGDMA). The buccal mucoadhesive force of [P(AA-co-PEGMM)] films increased with increasing content of PEGMM. [P{AA-co-PEGMM (18 mole%)}] films showed a significantly greater mucoadhesiveness than cr-PAA and cr-PEGMM films. The mucoadhesive force measured in normal saline (pH 5.0) was higher than that measured in phosphate buffer (pH 6.8) because of the pH dependence of hydrogels with carboxyl ions within the PAA. Moreover, the mucoadhesive force of [P{AA-co-PEGMM (18 mole%)}] films was at maximum after 2 hr attachment of buccal mocosa and it was maintained over $1\;N/cm^2$ for up to 10 hr. In dissolution studies, the release of butorphanol tartrate from [P(AA-co-PEGMM)] films increased with increasing PEGMM content, and films prepared with 18 mole% PEGMM gave almost zero order release kinetics.

• Membrane Journal
• /
• v.26 no.4
• /
• pp.281-290
• /
• 2016

Thin film composite (TFC) polyamide membranes were prepared on polysulfone (PSF) supports for forward osmosis (FO) applications. To understand the influence of polarity and porosity of support layer on the formation of polyamide structure and the final FO performance, clathochelate metal complex (MC) contained PSF supports were prepared via the phase inversion process from various PSF casting solutions containing 0.1-0.5 wt% of MC in dimethyl formamide (DMF) solvent (18 wt%). A crosslinked aromatic polyamide layer was then fabricated on top of each support to form a TFC membrane. For the porous PSF supports prepared with relatively low concentration casting solutions (12 wt%), the PET film was removed after phase inversion and crosslinked aromatic polyamide layer was then fabricated. The tested sample from PSF (18 wt%)/MC (0.5 wt%) casting solution presented outstanding FO performance, almost similar water flux (9.99 LMH) with lower reverse salt flux (RSF, 0.77 GMH) compared to commercial HTI FO membrane(10.97 LMH of flux and 2.2 GMH of RSF). By addition of MC in casting solution, the thickness of the active layer in FO membranes was reduced, however, the increased RSF value was obtained.

• Membrane Journal
• /
• v.19 no.3
• /
• pp.228-236
• /
• 2009

ABA type triblock copolymer of poly(hydroxyl ethyl acrylate )-b-polystyrene-b-poly(hydroxyl ethyl acrylate), i.e. PHEA-b-PS-b-PHEA, was synthesized throughatom transfer radical polymerization (ATRP). This block copolymer was thermally crosslinked with 4,5-imidazole dicarboxylic acid (IDA) via the esterification between the -OH groups of PHEA in block copolymer and the -COOH groups of IDA. Upon doping with ${H_3}{PO_4}$ to form imidazole-${H_3}{PO_4}$ complexes, the proton conductivity of membranes continuously increased with increasing ${H_3}{PO_4}$ content. The PHEA-b-PS-b-PHEA/IDA/${H_3}{PO_4}$ polymer membrane with [HEA]:[IDA]:[${H_3}{PO_4}$]=3:4:4 exhibited a maximum proton conductivity of 0.01 S/cm at $100^{\circ}C$ under anhydrous conditions. Thermal gravimetric analysis (TGA) shows that the PHEA-b-PS-b-PHEA/IDA/${H_3}{PO_4}$ complex membranes were thermally stable up to $350^{\circ}C$, indicating their applicability in fuel cells.

• Membrane Journal
• /
• v.23 no.4
• /
• pp.290-296
• /
• 2013

Poly(vinylidenefluoride-co-chlorotrifluoroethylene) P(VDF-co-CTFE) polymer was attached to methacrylic acid (MAA) in the presence of 1,8-diazabicyclo[5,4,0]undec-7-ene(DBU) catalyst to prepare P(VDF-co-CTFE)-MAA copolymer. The modified P(VDF-co-CTFE)-MAA was polymerized with 2-sulfoethyl methacrylate (SEMA) monomer in the presence of 4',4'-azobis(4-cyanovaleric acid(ACVA) initiator by free radical polymerization to form the proton conducting membrane. The ratio of the SEMA was increased in the membrane to increase the presence of the acidic group. The maximum IEC value that was observed at 50% SEMA was around 0.82 meq/g, which is consistent with the water uptake value. The highest proton conductivity achieved by P(VDF-co-CTFE)-MAA/SEMA membrane with 50% SEMA was approximately 0.041 S/cm. This indicates that the available ionic group for the proton conduction increases with the increase in the SEMA in the membrane.

• Molecules and Cells
• /
• v.27 no.1
• /
• pp.39-45
• /
• 2009

Ligand-dependent or independent oligomerization of receptor protein tyrosine kinase (RPTK) is often an essential step for receptor activation and intracellular signaling. The novel oncogene with kinase-domain (NOK) is a unique RPTK that almost completely lacks an ectodomain, expresses intracellularly and activates constitutively. However, it is unknown whether NOK can form oligomer or what function oligomerization would have. In this study, two NOK deletion mutants were generated by either removing the ectodomain ($NOK{\Delta}ECD$) or including the endodomain (NOK-ICD). Co-immunoprecipitation demonstrated that the transmembrane (TM) domain of NOK was essential for its intermolecular interaction. The results further showed that NOK aggregated more closely as lower order oligomers (the dimer- and trimer-sized) than either deletion mutant did since NOK could be crosslinked by both Sulfo-EGS and formaldehyde, whereas either deletion mutant was only sensitive to Sulfo-EGS. Removing the NOK TM domain (NOK-ICD) not only markedly promoted higher order oligomerization, but also altered the subcellular localization of NOK and dramatically elevated the NOK-mediated constitutive activation of extracellular signal-regulated kinase (ERK). Moreover, NOK-ICD but not NOK or $NOK{\Delta}ECD$ was co-localized with the upstream signaling molecule RAS on cell membrane. Thus, TM-mediated intermolecular contacting may be mainly responsible for the constitutive activation of NOK and contribute to the autoinhibitory effect on RAS/MAPK signaling.

• Korean Chemical Engineering Research
• /
• v.58 no.4
• /
• pp.618-623
• /
• 2020

Spherical phenolic resin beads were synthesized by suspension polymerization at 98 ℃ from phenol, ortho-cresol, formaldehyde, with triethylamine as a basic catalyst, and spherical phenol-cresol copolymer resin beads with relatively low crosslinking density as well. Phenol reacts with formaldehyde at two ortho- and one para- positions to form a crosslinked structure, but ortho-cresol instead of phenol reduces the crosslinking density during copolymerization due to the methyl group at a ortho- position. As a result, spherical phenol-cresol copolymer beads showed more shrinkage with decreasing apparent density compared to the spherical phenol beads when carbonized at 700 ℃ under nitrogen. As the molecular weight of the cresol oligomer increases, the pore radius of the carbonized copolymer beads decreases, which is consistent with the density and shrinkage results. It was confirmed that the characteristics such as density decrease, shrinkage, yield and so on during carbonization can be controlled by controlling the degree of crosslinking of the spherical phenolic resin particles with cresol.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.511-516
• /
• 2005

In this work, the crosslinked-chitosan microcapsules containing fragrant oil were prepared by oil-in-water-in-oil (O/W/O) multi-emulsion method. The effects of concentration of fragrant oil and stirring rates on the preparing of the microcapsules were investigated. The diameter and form of the microcapsules were observed by scanning electron microscope (SEM). As a result, the average particle size of microcapsules was decreased with increasing the stirring rate. The formation of chitosan microcapsules was comfirmed by FT-IR. The inclusion of fragrant oil into chitosan microcapsules was determined in the presence of specific peak of fragrant oil, i.e., $1,460cm^{-1}$, $2,960cm^{-1}$. Also, the release behavior or profile of fragrant oil from chitosan microcapsules was examined with UV/vis spectra. Released amounts of fragrant oil were increased with increasing as the content of fragrant oil and decreasing the pH.

• Smart Structures and Systems
• /
• v.22 no.2
• /
• pp.161-166
• /
• 2018

In the last decade, there has been an exponential increase of scientific interest in smart additive manufacturing (AM) technology. Among the different AM techniques, one of the most commonly applied processes is digital light processing (DLP). DLP uses a digital projector screen to flash an ultraviolet light which cures photopolymer resins. The resin is cured to form a solid to produce parts with precise high dimensional accuracy. During the curing process, there are several process parameters that need to be optimized. Among these, the exposure time affects the quality of the 3D printed specimen such as mechanical strength and dimensional accuracy. This study examines optimal exposure times and their impact on printed part. It was found that there is optimal exposure time for printed part to have appropriate mechanical strength and accurate dimensions. The gel fraction and TGA test results confirmed that the improvement of mechanical properties with the increasing UV exposure time was due to the increase of crosslinked network formation with UV exposure time in acrylic resins. In addition, gel fraction and thermogravimetric analysis were employed to microscopically investigate how this process parameter impacts mechanical performance.

• Archives of Plastic Surgery
• /
• v.33 no.1
• /
• pp.13-20
• /
• 2006

Alginate, which is isolated from brown seaweed, is a bioabsorbable long chain polysaccharides, ${\beta}$-D-mannuronic acid and ${\alpha}$-L-guluronic acid. The authors produced alginates and alginate-colllagen as a disc form. Then, to evaluate the efficacy of alginate and alginate-collagen complex as a wound healing material, three full-thickness skin defects of 2 cm in diameter were made at the back of the New Zealand white rabbits. Three groups of dressing materials-alginate, alginate-collagen complex and vaseline gauze as control group - were applied on the wound and the results were evaluated grossly and histopathologically. The authors compared gross findings of sizes of healed wound, wound epithelization and wound contraction by tracing the remaining wound area at 5th, 10th, 15th, 20th, 25th day after wound introduction, and wound biopsy was performed at 3rd, 7th, 14th, 21st day, respectively. Alginate and alginate-collagen complex showed statistically higher percentage of wound contraction and wound healing compared to control group(p<0.05). Alginate-collagen complex showed statistically higher percentage of wound contraction, epithelization and wound healing compared to alginate alone. In conclusion, the result suggests that alginate has a good effect of wound healing and that alginate-collagen complex is more effective in wound healing than alginate alone.

• Membrane Journal
• /
• v.19 no.2
• /
• pp.89-95
• /
• 2009

A comb-like copolymer consisting of a poly(vinyl chloride) backbone and poly(hydroxy ethyl acrylate) side chains, i.e. PVC-g-PHEA, was synthesized through atom transfer radical polymerization (ATRP). This comb-like copolymer was crosslinked with 4,5-imidazole dicarboxylic acid (IDA) via the esterification of the -OH groups of PHEA in the graft copolymer and the -COOH groups of IDA. Upon doping with phosphoric acid (PA, $H_3PO_4$) to form imidazole-PA complexes, the proton conductivity of the membranes continuously increased with increasing PA content. A maximum proton conductivity of 0.011 S/cm was achieved at $100^{\circ}C$ under anhydrous conditions. The PVC-g-PHEA/IDA/PA complex membranes exhibited good mechanical properties, i.e. 575 MPa of Young's modulus, as determined by a universal testing machine (UTM). Thermal gravimetric analysis (TGA) shows that the membranes were thermally stable up to $200^{\circ}C$.