• Restorative Dentistry and Endodontics
• /
• 제34권1호
• /
• pp.1-7
• /
• 2009

이 연구의 목적은 3차원 유한요소 모형 분석을 이용하여 삼각 대칭형과 5형태의 단면 및 변형된 사각 형태인 장방형 단면으로 분류되는 네 종류의 니켈티타늄 파일이 만곡 근관 적용 시의 응력 분포를 비교하는 것이다. 삼각 대칭형 단면 구조의 ProFile #30 / .06과 Heroshaper #30 / .06, 장방형 단면구조의 Mtwo #30 / .05와 NRT #30/ .06 파일을 마이크로컴퓨터 단층촬영을 하고 reverse engineering을 통하여 파일의 구조를 얻고 삼차원 유한요소모형을 제작하였다. 모형 근관 내에서 파일이 근관장끝까지 진입하여 회전할 때 발생하는von Mises 응력 분포 및 파일의 제거후의 잔류 음력의 분포양상을 ABAQUS 프로그램을 이용하여 비교하였다. 근관 내 회전 시에 발생하는 응력을 관찰하였을 때 NRT 파일에서 가장 큰 응력을 나타냈으며, 각 파일에서의 최고 응력과 최저 응력을 비교하였을 때 Mtwo파일에서 가장 큰 차이가 나타났다. 응력의 내부 분포 경향을 보았을 때 장방형 구조의 단면을 가진 Mtwo 및 NRT 파일에서 불연속적인 응력의 집중 부위가 관찰되었으며, 근관 외부로 파일을 제거하여 탄성 회복이 일어난 후의 잔류 응력도 NRT 파일에서 가장 높게 나타났다. 이상의 결과로 유추할 때, 삼각대칭 단면 구조를 가진 파일보다 S-형태의 단면과 변형된 사각 형태의 단면 등의 장방형 단면 구조의 파일이 파절의 위험성이 더 클 것으로 사료된다.

• 기술혁신연구
• /
• 제23권2호
• /
• pp.33-54
• /
• 2015

국가차원의 슈퍼컴퓨팅 성능수요 예측은 슈퍼컴퓨터를 활용하는 계산과학분야의 연구자나 연구개발 인프라를 구축 운영하고 있는 전문기관, 과학기술 인프라구축을 주도할 정부기관에 있어서 매우 중요한 정보이다. 본 연구는 그동안 진행되었던 슈퍼컴퓨터 성능관련 예측활동 분석을 통해 과학기술 역량에 영향을 미치는 요인들을 도출하고 이를 슈퍼컴퓨터 기술진보 추세에 적용한 복합 예측모형을 제안하였다. 횡단면분석에서는 슈퍼컴퓨팅 성능에 영향을 미칠 것으로 판단되는 GDP, GERD, 연구원수, SCI논문수를 고려한 다중회귀분석을 수행하였다. 그리고 횡단면분석 결과에 Top500 자료의 성능(Rmax)값을 이용한 시계열분석을 통해 도출된 기간별 기술진보율을 곱하여 슈퍼컴퓨터의 성능을 예측하였다. 제안된 예측모형을 바탕으로 세계 슈퍼컴퓨터 500위의 시계열자료를 이용하여 한국이 2016년에 보유해야 할 슈퍼컴퓨터 성능규모를 예측하였다. 횡단면분석과 기술진보율을 적용하여 2016년 한국의 슈퍼컴퓨팅 성능수요를 예측해본 결과 현재의 추세를 이용할 경우 15~30PF 정도, 목표 국가수준의 추세를 이용할 때 20~40PF 정도의 컴퓨팅 역량이 필요할 것으로 예측되었다. 이 결과는 단순 회귀분석을 적용한 결과인 9.6PF와 횡단면분석을 적용한 결과인 2.5PF와 큰 차이를 나타내었다.

• Wind and Structures
• /
• 제12권5호
• /
• pp.413-424
• /
• 2009

A series of wind tunnel free-decay sectional model dynamic tests were conducted to examine the effects of torsional-to-vertical natural frequency ratio of 2DOF bridge dynamic systems on the aerodynamic and dynamic properties of bridge decks. The natural frequency ratios tested were around 2.2:1 and 1.2:1 respectively, with the fundamental vertical natural frequency of the system held constant for all the tests. Three 2.9 m long twin-deck bridge sectional models, with a zero, 16% (intermediate gap) and 35% (large gap) gap-to-width ratio, respectively, were tested to determine whether the effects of frequency ratio are dependent on bridge deck cross-section shapes. The results of wind tunnel tests suggest that for the model with a zero gap-width, a model to approximate a thin flat plate, the flutter derivatives, and consequently the aerodynamic forces, are relatively independent of the torsional-to-vertical frequency ratio for a relatively large range of reduced wind velocities, while for the models with an intermediate gap-width (around 16%) and a large gap-width (around 35%), some of the flutter derivatives, and therefore the aerodynamic forces, are evidently dependent on the frequency ratio for most of the tested reduced velocities. A comparison of the modal damping ratios also suggests that the torsional damping ratio is much more sensitive to the frequency ratio, especially for the two models with nonzero gap (16% and 35% gap-width). The test results clearly show that the effects of the frequency ratio on the flutter derivatives and the aerodynamic forces were dependent on the aerodynamic cross-section shape of the bridge deck.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.224-231
• /
• 2021

Recently, the waterproofing performance of high-voltage connectors in automotive vehicles has attracted increased interest. In this study, an optimal cross-sectional shape was derived to obtain uniform contact pressure and strain by considering stress relaxation problems caused by initial tension when mounting a seal. A high strain of 52.1 was distributed in the round region, owing to excessive initial tension. The finite element method (FEM) analysis indicated that the strain corresponding to the optimal initial tensile was 11. We adopted six design factors to optimize the seal cross-section and three factors as the main design factors. An orthogonal arrangement table was prepared using Minitab. FEM analyses of 16 study models were conducted to determine the optimized model. The contact pressure of the optimization model is the most evenly distributed while satisfying the waterproof performance of 0.47 MPa. Compared to the initial model, the difference in strain decreases from 35.5% to 19.6%. Finally, the derived cross-sectional shape can reduce the strain of the round region by 33.8% and the differences in the contact pressure at the upper and lower surfaces by 42% and 76%, respectively.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1582-1590
• /
• 2011

An analysis of the railroad industry for R&D investments has been insufficient whereas there are lots of analysis of accumulation of technology, economic performances and ripple effects for macroscopic view and other industry of R&D investments. This study decided intellectual rights, patent, and paper as common indicators of scientific and technological performances for setting up performance targets through surveying and analysis of preceding study and verified a appropriateness of scientific and technological performances for railroad R&D 11 projects which were successfully finished. Preceding study has been set up performance targets by research investments as input, but this study made a performance target by model through a cross-sectional and residual analysis of performances of railroad R&D 11 Projects in applying research investments, capital investments, inner labor cost and inner labor cost per man and research time as inputs, and verified a validity and a empirical analysis through analysis of other project.

• 대한기계학회논문집B
• /
• 제22권6호
• /
• pp.823-831
• /
• 1998

In order to investigate the impulsive noise at the exit of high-speed railway tunnel and the pressure transients inside the tunnel, numerical calculations using a Total Variation Dimishing difference scheme were applied to axisymmetric unsteady compressible flow field. Some compression wave forms were assumed to model the compression wave produced in real high-speed railway tunnel. The numerical data were extensively explored to analyze the peak over-pressure and maximum pressure gradient in the pressure wavefront. The effect of the distance and cross-sectional area ratio between two-continuous ducts on the characteristics of the pressure waves were investigated. The peak over-pressure inside the second duct decreases for the distance and cross-sectional area ratio between two tunnels to increase. The peak over-pressure and maximum pressure gradient of the pressure wavefront inside the second duct increase as the maximum pressure gradient of initial compression wave increases. The present results were qualitatively well agreed with the results of the previous shock tube experiment.

• 물과 미래
• /
• 제8권2호
• /
• pp.75-80
• /
• 1975

The fluvial phenomena in the bended natural river course are studied experimentally. Some theoretical and empirical conclusions were derived in prior to this study by some authors but the limitation of applicability of those results are not clearly known because of the sensitibitys of the flow regime in the reach. The main objective of this study is directed to evaluate the mechanism of sedimentation and the cross sectional changes in the equilibrium status. the most governing factor influenced to the cross sectional changes in the bended reach is the occurance of spiral flow. In this study, the streamlines and velocity distributions are checked at given interval by the hydraulic model to find out the place where spiral flow are existing under the various flow magnitudes.

• 노동경제논집
• /
• 제31권2호
• /
• pp.103-128
• /
• 2008

본 연구는 "한국노동패널조사" 자료를 사용하여 노동조합이 임금에 미치는 효과를 패널 분석하였다. 횡단면 분석을 통하여 구한 노동조합이 임금상승에 미치는 효과는 약 4.6%로 추정되었다. 고정효과 모델을 통하여 추정된 노조의 임금상승효과는 약 2.1%로 상당히 그 효과가 감소하였음을 알 수 있다. 따라서 보이지 않는 근로자의 특성과 노조가 있는 기업에 종사하며 노동조합에 가입하는 의사결정과 양(+)의 상관관계가 존재함을 유추해 볼 수 있으며 기존의 횡단면 분석의 연구 결과가 상당 부분 상향 편의되었음을 유추해 볼 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1085-1088
• /
• 2001

The process of styrofoam pattern that has been used for material of press die pattern depends chiefly on handwork. Laser manufacturing system developed to increase precision and efficiency of process that is also able to convert the design easily. Applying the RP(rapid prototyping) concept reversely, the unnecessary part of section is vapored away by heat source of laser beam after converting 3-D CAD model into cross-sectional shape information. Laser beam is line-scanned in plane specimens to measure the depth and width of cut, surface roughness, cross-sectional shape as converting laser power, scanning speed, cutting gas pressure. With these basic data, plane surface, inclined surface, hole, outer contour trimming process is experimented and optimum condition are obtained. In plane and inclined surface experiments, 15W laser power and 50mm/s scanning speed make superior processing property and 30W, 10mm/s make processing efficiency increase in trimming process. With these results, simple patterns were manufactured and the possibility of applying laser manufacturing system to styrofoam pattern was convinced.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.95-98
• /
• 2003

In this work, a closed-form analysis is performed to obtain the stiffness coefficients of thin-walled composites beams with elliptical profiles. The analytical model includes the effects of elastic couplings, shell wall thickness, torsion warping and constrained warping. Reissner's semi-complementary energy functional is used to derive the beam force-displacement relations. The theory is validated against MSC/NASTRAN results for coupled composites beams with single-cell elliptical sections. Very good correlation has been noticed for the test cases considered.