• Journal of Technology Innovation
• /
• v.28 no.4
• /
• pp.63-93
• /
• 2020

We suggest a new way of specifying the co-evolution of product and process technologies, and integrating it into one of the well-received technology intelligence tools - a technology radar. Cross impact analysis enables us to identify the core technologies of product-process co-evolution. Combining expert judgment with its results, we can clarify the technological co-evolution trajectory with mainstream as well as emerging core technologies. Reflecting these in the assessment process of a technology radar, we could improve reliance of the technology assessment process and technology portfolio. From the academic perspective, our research provides a point where the co-evolution theory encouners technology intelligence methods. Practically, strategic capability of future-preparedness and strategic management could improve by adopting our method based on our example of co-evolution of semiconductor product and process technologies.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.24-29
• /
• 2017

In this study, a seat cross member was fabricated by optimizing the resin transfer molding processing of CFRP (Carbon Fiber Reinforced Plastics) materials. This seat cross member is used in automotive underbody parts and provides side impact support. The seat cross was manufactured via vacuum resin transfer molding. The process included 1min of resin injection, 8 mins of heating, and 1 min of cooling, for a total molding time of 10mins. Tensile test results showed an average breaking load of 21.50kN, a tensile strength of 404 MPa, and an elastic modulus of 46.2 GPa. As a result, the CFRP seat cross provides the same strength as a similar steel part, but weighs 42% less.

• The Journal of Korean Physical Therapy
• /
• v.34 no.1
• /
• pp.1-5
• /
• 2022

Purpose: The impact of prolonged sitting in a cross-legged posture on physiological factors has not been extensively studied. We therefore attempted to evaluate whether prolonged sitting in a cross-legged posture affects pulmonary function in normal young adults. Methods: Twenty-four participants were recruited in this study, and the participants were equally allocated to the normal sitting posture group (NSP group, n=12) or sitting posture with the cross-legs group (SPCL group, n=12). The NSP group sat on chairs without crossing their legs for 30 minutes, and the SPCL group sat on the chair with legs crossed (the right knee on the left knee or the left knee on the right knee) for 30 minutes. The pulmonary function of the subjects was evaluated based on forced vital capacity (FVC), forced expiratory volume in one second (FEV1), FVC/FEV1, and peak expiratory flow (PEF) measured using a spirometer. Results: In the intra-group comparison, the SPCL group showed significant differences in FVC and FEV1 before and after sitting (p<0.05), but no significant differences (p>0.05) were observed in the NSP group. However, there were no significant differences between the two groups in the pulmonary function parameters measured before and after sitting (p>0.05). Conclusion: Our results confirmed that prolonged sitting in a cross-legged posture could have a negative influence on pulmonary function. Therefore, if a sitting position is maintained for a long time, the correct sitting posture should be maintained to prevent musculoskeletal disorders as well as to maintain normal pulmonary function.

• Transactions of Materials Processing
• /
• v.32 no.4
• /
• pp.221-227
• /
• 2023

While tube bending is a conventional forming technique, it is still used to make curved products for load-bearing members or aesthetically pleasing parts in various manufacturing industries such as automotive, aerospace, and others. Whole or local deformation of the final product such as springback, distortion, or local buckling are of interest in metal forming or precision manufacturing. In this paper, the factors affecting the cross-sectional deformation are explored. A 5-axis stretch bending machine was used for two-dimensional bending with extruded AA6082-T4 rectangular tubes. Three different bending sequences were employed: stretch before bending, stretch after bending, simultaneous bending and stretch. Furthermore, by considering both the stretch and bending angle, cross-sectional deformation was also analyzed. It was observed that employing stretch bending techniques can effectively reduce cross-sectional deformation and contribute to overall quality enhancement. Through this study, it was revealed that these factors have an impact on the cross-sectional deformation of the tubes.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1824-1832
• /
• 1992

This study investigated the compressive Young's modulus and the impactinduced damage of CFRP angle-ply laminate under same impact energy condition. The specimens of angle-ply laminate composites [0.deg.$_{6}$/ .theta..deg.$_{10}$/ 0.deg.$_{6}$] with .theta..deg. =30.deg., 45.deg., 60.deg. and 90.deg. were employed, and damaged by steel balls of diameter of 5mm and 10mm propelled by air gun type impact testing machine. The impact damaged zones were observed through a scanning acoustic microscope(SAM), and their cross-sections were observed through a scanning electron microscope(SEM). The compressive Young's moduli before and after impact were measured, and compared with the theoretical values calculated. The results obtained were as follows: (1) The damage areas on the interfacial boundaries showed more severe change on the back side interface than on the impact side interface with increasing ply-angle. (2) The damage areas on the interfacial boundaries became larger with increasing impact velocity or ply-angle. (3) The impact damaged zone showed the delamination on the interfacial boundaries and transverse cracks inside laminas. (4) The impact damaged zone was affected by the impactor size and speed or ply-angle under same impact energy condition. (5) Compressive Young's moduli before and after impact were lower than theoretical value, but showed a similar change according to ply-angle. (6) Compressive Young's moduli after impact were higher than those before impact, but there was no remarkable change in apparent compressive modulus after impact.t.act.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.74-77
• /
• 2001

The impact response and damage of CLAS panel was investigated experimentally. The facesheet material used was RO4003 woven-glass hydrocarbon/ceramic and the core material was Nomex honeycomb with a cell size of 3.2mm and a density of 96 kg/$\textrm{m}^{3}$. The shield plane used was RO4003 and 2024-T3 aluminum. Static indentation and impact test was conducted to characterize the type and extent of the damage observed in two CLAS panels, and the performance of antenna used in a wireless LAN system. Correlation of peak contact force, residual indentation and the delamination area shows impact damage of the panel with an aluminum shield plane is larger than that of the panel with RO4003 shield plane, although tile former is more penetration resistant. The damage was observed by naked eye, ultrasonic inspection and cross sectioning. The shape and size of delamination was estimated by ultrasonic inspection, and the area of delamination linearly increases as impact energy increases. The performance of impact damaged antenna was estimated by measuring return loss and radiation pattern.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.372-380
• /
• 2003

Impact tests were conducted to study the effect of angle ply and metal laminate on impact damage characteristics of Fiber Metal laminates (FML). Impact tests were conducted using drop weight impact machine and damage behavior were analyzed by comparing with load-displacement curve and surface observation and microscopic observation of cross sections. The effect of angle ply on impact characteristics of FML are influenced by property of metal laminate. i.e., when the metal laminate is not enough to strong to prevent fiber debonding, Angle ply FML is superior to singly oriented ply (SOP) FML because angle ply enhance the stiffness by fiber supports and prevent (rack propagation. However, when the metal laminate is enough to strong to prevent fiber debonding, SOP FML is superior to Angle ply FML because the fiber of lower ply in Angle ply FML are more stressed than that of SOP FML.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.82-87
• /
• 2012

The purpose of this study is to produce a side impact beam with high tensile steel using a roll forming process. The door side impact beam plays an important roll in a car because it protects passengers from external crash. The roll forming process is a continuous bending process wherein a long metal sheet is bended as it continuously passes several rolls. The characteristic of this study is that an impact beam is produced by a continuous process using a ultra high strength steel without a hardening heat treatment. A model was determined by analysing plasticity of a cross section shape considering high strength. Design parameters of the impact beam was determined by crash-analysing the model. Workpiece products were manufactured by designing dies for roll forming and setting them up in a following process line. Results of a bending test and a FEM analysis was considered and reviewed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.231-234
• /
• 2009

Based on combined continuum-fracture mechanics, fracture criterion was utilized to predict impact performance of advanced high-strength steel sheets: 340R and TWIP940. The macro-crack propagation behavior at high stress triaxiality was characterized by V-notch tests while deformation behavior at high strain rate was characterized by simple tension tests with various cross head speeds. The characterized mechanical properties were incorporated into the FE program ABAQUS/Explicit to simulate the charpy impact tests, which showed good agreement with experiments.

• Transactions of Materials Processing
• /
• v.21 no.3
• /
• pp.172-178
• /
• 2012

We performed a shot peening test and used a 2-D finite element model which predicts the compressive residual stress distribution below the material's surface. In this study, the concept of 'impact cycle' is introduced to account for the irregularity in the shot's impact position during testing. The impact cycle was imbedded in the finite element model. In the shot peening test, shot bombarded a type-A Almen strip surface with different impact velocities. To verify the proposed finite element model, we compared the deformed cross sectional shape of the Almen strips with the shapes computed by the proposed finite element model. Good agreement was noted between measurements and the finite element model predictions. With the verified finite element model, a series of finite element simulations was conducted to compute the residual stress distribution below the material's surface and the characteristics of these distributions are discussed.