• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Tuberculosis and Respiratory Diseases
• /
• 제44권2호
• /
• pp.241-250
• /
• 1997

목 적 : 결핵에 대한 국가결핵관리사업이 시작된 이후 결핵의 점차적으로 감소하고 있기는 하나 최근에 다제내성균결핵환자가 심각할 정도로 증가하고 있다. 다제내성균결핵은 기존의 항결핵제에 잘 반응하지 경향이 있으며 이는 낮은 치료순응도, 2차약제의 높은 부작용 그리고 사용할 수 있는 약제의 수가 많지않은 때문으로 생각된다. 본 연구의 목적은 일개 국립결핵병원에서 입원치료중인 결핵환자의 임상양태를 살펴보고 기존의 결핵치료의 문제점을 파악하여 궁극적으로 다제내성균결핵을 포함한 결핵의 치료효율을 개선시키고자 함이다. 방 법 : 1995년 12월 30일을 기준시점으로 국립마산결핵병원에 임원한 환자 336명을 대상으로 성별 및 나이, 처음결핵을 발견하게된 계기, 가족력, 환자의 생활근거지의 지역별 분포, 과거결핵치료력 등의 역학적 조사와 입원 당시의 주증상, 흉부 X-선 사진상의 병소별 분포, 동반질환 그리고 결핵치료중에 발생한 부작용등 임상양태에 대한 조사와 입원전 사용한 약제별 분류와 약제감수성검사의 결과 등에 대해 descriptive cross-sectional study를 시행하였다. 결 과 : 연령별 분포는 20대에서 50대까지 고른 분포를 보였으며 성별로는 남자가 269예로 압도적으로 많았다. 발견계기별 분포는 보건소가 64.6%로 가장 높았다. 입원당시 주증상으로는 체중감소가 가장 흔했으며 다음으로는 기침, 호흡곤란 등의 순서였다. 흉부 X-선 사진상 병소별 분포는 양측성 병소를 가진 예가 201예로 가장 많았다. 동반질환을 가진 경우가 130예 였는데 그 중 당뇨가 49예로 가장 많았으며 다음으로는 간질환, 정신질환 등의 순서였다. 95예에서 가족력이 있었는데 부모가 결핵을 앓았던 경우가 40예로 가장 많았으며 다음으로는 형제, 부부 등의 순서였다. 결핵을 처음 진단받은 시기별 분포에서 1980년 이전은 31예 였으나 이후 최근으로 오면서 약간씩 증가하는 추세였다. 지역별 분포로는 부산, 경남지역이 압도적으로 많았다. 과거치료력을 가진 258예중 1회의 치료력을 가진 경우는 86예, 2회가 60예 그리고 3회이상이 112예 였다. 과거치료력을 가진 환자의 약제순응도별 분포는 133예만이 규칙적으로 복약하였다. 입원전 사용한 약제별 분포는 INH, EMB, RFP, PZA 등을 사용한 경우가 82예, INH, EMB, RFP 등을 사용한 경우가 50예 였으며 INH, EMB, RFP, PZA 이외 1가지 약제를 더 사용한 경우는 20예, 3가지 이상의 약제를 더 사용한 경우는 97예 였다. 154예를 대상으로 약제감수성검사를 한 결과 5제 이상 내성이 생긴 경우가 77예 였다. 치료도중 발생한 부작용으로는 위장장애가 58예로 가장 많았으며 다음으로는 피부발진 및 소양감 그리고 관절통 등의 순서였다. 결 론 : 원인 모를 체중감소가 있을 때에는 결핵을 의심해 볼 수 있을 것으로 생각된다. 결핵을 치료할 때 환자에게 결핵의 치료과정에 대해 충분한 설명을 해 줌으로 치료의 순응도를 높일 수 있을 것으로 생각된다. 초치료시 균음전화시기가 늦다든지, 여러가지 상황으로 치료에 실패 할 가능성이 높다든지 환자의 여건상 지속적인 항결핵제 투여가 어렵다고 생각될 때는 수술요법이 고려되어야 할 것으로 생각된다. 초치료실패후 재치료약제를 선택할 때는 이전에 사용한 초치료약제와 혼용처방이 되지않도록 주의해야 할 것으로 생각된다.

• Current Research on Agriculture and Life Sciences
• /
• 제1권
• /
• pp.11-18
• /
• 1983

건과육중(乾果肉重)(또는 건과육율(乾果肉率)이 상대적(相對的)으로 많은 건과용(乾果用) 고추를 육성(育成)하는데 기초자료(基礎資料)를 얻고자 8개친(個親)과 이면교배(二面交配)한 $F_1$ 28조합(組合)을 공시(供試)하여 1건과중(乾果重)에 대(對)한 구성요소(構成要素)의 비율(此率)을 조사(調査)하고 과경중(果梗重), 태좌중(胎座重), 종자중(種子重) 및 과육중(果肉重)의 잡종강세(雜種强勢), 조합능력(組合能力) 및 유전(遺傳) 분석(分析)을 한바 얻어진 결과(結果)는 다음과 같다. 친(親)과 $F_1$에 있어서 1건과중(乾果重)과 구성요소(構成要素)들은 초기과(初期果)가 중기과(中期果)에서 보다 모두 무거웠다. 그리고 초(初), 중기과(中期果)에 있어서 이들은 모두 친간(親間), $F_1$간(間)에 1%의 유의(有意)를 나타내었고, $F_1$이 친(親)보다 무거웠으나 초기과(初期果)의 친(親)은 중기과(中期果)의 $F_1$보다 무거웠다. 1건과중(乾果重)에 대(對)한 구성요소(構成要素)들의 비율(比率)은 과육(果肉)이 가장 높고 다음은 종자(種子)였다. 과육율(果肉率)은 초기과(初期果)보다 중기과(中期果)에서 다소(多少) 증가(增加)되었고 종자율(種子率)은 상대적(相對的)으로 감소(減少)되었으며 과경(果梗)과 태좌(胎座)는 수확시기(收穫時期)에 따른 차이(差異)가 없었다. 무거운 친(親)을 초월(超越)하는 $F_1$조합(組合)이 상당(相當)히 있었으며 평균(平均)heterosis(%)는 모두 정(正)의 값을 나타내었고 평균(平均)heterosis(%)는 종자(種子)와 1건과중(乾果重) 외(外)는 모두 부식(負植)를 나타내었다. GCA는 SCA는 모두 1%의 유의성(有意性)을 나타내었으며 GCA가 SCA보다 컸다. 무거운 쪽이 모두 우성(優性)을 나타내었고 과경(果梗)은 부분우성(部分優性), 태좌(胎座), 과육(果肉) 및 1건과중(乾果重)은 완전우성(完全優性), 종자(種子)는 초우성(超優性)을 타나내었다. 유효유전자수(有效遺傳子數)는 과경(果梗)과 태좌(胎座)는 1개(個), 종자과육(種子果肉) 1건과중(乾果重)은 2개(個)로 추정(推定)되었으며 유전력(遺傳力)은 모두 높았다.

• 한국수자원학회논문집
• /
• 제48권7호
• /
• pp.553-566
• /
• 2015

ADCP는 하천의 3차원 유속과 수심 자료를 매우 효율적이고 빠르게 측정할 수 있으며, 그 자료의 공간 및 시간적 해상도는 기존의 전통적인 유속 측정 방법들과 비교하여 매우 정밀하다는 장점이 있다. 하지만 ADCP는 하상 부근과 센서 근처에서의 미계측 영역이 발생하고 이 미계측 영역의 유속을 얼마나 정확하게 산정하느냐에 따라 ADCP 유량 측정의 정확도에 영향을 미친다. 본 연구에서는 ADCP 유량 산정 시 범용적으로 활용되고 있는 1/6 멱법칙(power law)을 활용한 미계측 영역의 유량 측정 결과의 정확도를 분석하였다. 이를 위해 실규모 직선수로에서 ADCP를 고정시킨 상태에서 측정한 유속 자료를 1/6 멱법칙과 대수 법칙(log law)을 적용하여 외삽 한 유속분포와 유량 산정 결과를 ADV를 이용하여 정밀하게 측정한 결과와 비교하였다. 비교 결과 전체적으로 대수 법칙으로 외삽한 경우가 높은 정확도를 나타냈으며, 수표면 근처 미계측 영역에서는 1/6 멱법칙은 유량을 작게 산정하는 경향을 나타냈고, 하상 근처의 미계측 영역에서는 유량을 크게 산정하는 경향을 나타냈다. 이 결과는 기존 1/6 멱법칙을 활용한 하상 및 수표면 부근 미계측 영역 유량 추정 방법이 오차를 수반함을 의미한다. 따라서 ADCP 정지법 측정 방식을 사용할 경우, 대수 법칙이 1/6 멱법칙보다 정확한 상하부 미계측 유량 추정 결과를 보여주었으므로 대안으로 고려되어야 할 것이다. 또한 제방 근처 미계측 영역의 유량 측정 정확도를 높이기 위해서는 수심이 0.6 m 이상을 확보한 측선을 기준으로 유량을 산정할 경우 신뢰도 높은 유량 측정 결과를 보였다. 향후, ADCP 정지법 측정 방식에 비해 보다 많이 활용되고 있는 보트탑재 이동식 ADCP의 경우도 이와 같은 검증이 필요하다고 하겠다.

• 구강회복응용과학지
• /
• 제18권3호
• /
• pp.145-155
• /
• 2002

본 연구에서는 knitted glass fabric 강화 레진에 대한 치과보철소재로서의 적용가능성을 평가하기 위한 목적으로, 가장 높은 수준의 교합하중이 작용하게 되는 구치부 3본 고정성국소의치에 이 재료를 사용하는 경우에 대해 해석을 수행하였다. 우선 구치부3본 고정성국소의치에 대해 knitted glass fabric 강화 레진을 적용한 두 가지 설계 개념을 상정하였고, 각 설계형상에 대한 유한요소해석을 하였다. 강도 평가를 위해서75N의 생리적인 반복 수직 교합 하중 조건을 부여, 보철물에 유도되는 국소응력을 피로강도측면에서 고찰하였다. 각각의 설계에는 knitted glass fabric을 모재로 하고 보강재로 unidirectional 형의 glass 복합재가 사용되었다. 본 연구에서 개념설계 된 두 가지의 3본 고정성국소의치는 수직 교합 하중 75N 에 대해 충분한 강성과 강도를 가진 것으로 분석되었다. 가공치와 knitted caps사이의 연결 부위에서 국소적인 응력 집중이 관찰되었으나 그 크기는 재료의 피로강도 범위 이내였으며 국소적인 설계변경을 통하여 응력분포를 더욱 개선할 수 있을 것으로 추정하였다. 본 연구를 통해 knitted glass fabric 은 새로운 치과 보철 소재로서의 그 가능성이 기대된다.

• Journal of Astronomy and Space Sciences
• /
• 제24권2호
• /
• pp.125-134
• /
• 2007

이 연구에서는 태양 및 지자기 활동에 의해 발생한 우주환경변화가 우리나라 위성인 아리랑위성1호(KOMPSAT-1)의 궤도에 미치는 영향을 분석하였다. 인공위성의 궤도변화는 정상적인 상태에서도 자연적인 섭동에 의해 지속적으로 발생하지만, 거대한 태양폭발에 의한 지구 주변 우주환경이 급격히 변화할 때 고층대기의 밀도변화로 인해 크게 발생한다. 특히 이러한 현상은 아리랑위성 1호와 같이 저궤도 상에서 운영되는 위성에 직접적인 영향을 미친다. 이 때, 태양활동에 의한 지구 주변 우주환경의 변화는 크게 두 가지로 구분할 수 있다. 하나는 태양 플레어 (Flare)가 폭발했을 때 고에너지 복사(Radiation)로 인해 지구 고층대기가 가열되어 팽창하고 이런 결과로 고층대기에 있는 중성입자밀도가 급격히 증가하는 것이다. 다른 하나는 코로나 물질 방출(Coronal Mass Ejections) 등에 의해 발생한 지자기폭풍기간 동안 플라즈마 대류와 입자들의 하강으로 전기장이 강해져 상당량의 줄가열(Joule heating)과 하강입자가열(precipitating particle heating)이 발생하고 이로 인해 중성입자밀도가 증가하는 것이다. 두 가지 원인에 대한 영향을 구분하여 알아보기 위해, 우리는 태양 및 지자기 자료를 면밀히 분석하여 2001년에서 2002년 동안 5개의 기간을 선정하였다. 그 결과 위성의 대기저항가속도는 태양의 극자외선(Extreme Ultra-Violet)의 증가와 함께 약 하루 정도의 시간 지연을 가지고 유사하게 변화하고 있음을 확인하였다(R=0.92). 그리고 지자기폭풍이 발생한 기간동안 대기저항가속도는 지자기폭풍에 의한 Dst 변화와 상당히 유사하게 그리고 거의 동시에 급격히 변화하는 것을 확인하였다. 마지막으로 우리는 위성의 대기저항가속도의 변화는 전반적으로는 오랜 기간 동안 고에너지 복사에 의한 효과로 나타나고 있으나 짧은 기간(하루 미만) 동안 크게 발생하는 대기저항가속도의 변화는 지자기폭풍에 의한 효과로 보고 있다.

• 디자인학연구
• /
• 제18권1호
• /
• pp.91-104
• /
• 2005

디자인 교육은 과거 산업시대의 아름다움과 유용성을 목적으로 한 기업의 생산과 소비에 이르는 활동을 충족시키기 위한 기술만을 가르치는 역할에서, 모든 대중의 정신적, 물질적인 욕구를 조화 있게 충족시켜 인간다운 삶의 질을 고양시키는 교육으로의 전환이 필요하다. 왜냐하면 디자인 교육은 모든 사람의 미적 수준을 향상시켜 삶의 질을 향상시키고자 하는 아름다움에 대한 인격교육이기 때문이다. 이러한 관점에서 본 논문은 정보화 사회의 도래에 따른 사회 환경 변화와 교육문제, 대중의 교육과 디자인교육 필요성 등에 대해 이론적인 고찰을 통해 디자인 대중교육에 대한 중요성을 제시하였다. 먼저 문제제기 및 연구 필요성을 통해 연구의 당위성을 제시하였고 연구의 목적을 달성하기 저해 국내, 외 디자인 대중교육실태 및 문제점을 조사, 분석하였다. 이것을 토대로 대중의 디자인교육의 발전방향에 제시를 하였다. 결론적으로 첫째, 디자인분야의 교육을 수직적 구조에서 수평적 구조로 바꾸어야한다. 디자인교육은 특수계층만을 위한 폐쇄성을 벗어나 시대를 이끌고 있는 대중에 이르기까지 확대, 시행되어야 한다. 둘째, 디자인분야에 대한 디자이너와 대중의 인식전환이 시급히 전환되어야 한다. 디자이너만이 디자인을 하는 것이 아닌 모든 사람이 삶 속에서 문제를 발견하고 이를 해결하는 능력을 함양시켜야 한다. 셋째, 대중을 위한 디자인 교육은 전인교육이어야 한다. 대중적 미에 대한 교양교육으로 인식하고 교과의 경계를 넘어 인간의 삶과 문화와 통합되어 건강한 대중문화의 발전과 대중의 건강한 삶을 누릴 수 있는 지식으로 새롭게 구성되어야 한다.는 인간의 감성을 측정하는 데에 필요한 주관적 평가자료로 활용할 수 있을 것이다.랜드화 역시 중요한 변인이 될 수 있음을 확인할 수 있었다.지에 대한 고유한 특성을 파악할 수 있었다.인 기여가 큰 것으로 평가되었다. 퇴적물은 공간적으로 다소 불규칙한 변동이 있지만, 저질조성과 관련해서 양자강 하구쪽으로 갈수록 오염도가 낮고, 조사해역의 동쪽부분에서 유기오염의 정도가 상대적으로 크게 나타났지만, 그 오염도는 심하지 않는 것으로 분석되었다. 향후 본 대상해역에 있어서 산샤댐 건설과 관련된 양자강 유량의 변화, 그리고 어업활동과 관련된 폐기물에 의한 해양환경의 영향평가 및 대책 연구가 수행되어져야 할 것이다. 시도는 긍정적으로 평가되어야 한다. 그러므로 앞으로는 제품디자인 뿐만이 아닌 다른 다양한 분야들에게로 그 범위가 확대되어 디자인 문화적 정체성을 확립하는 연구가 뒤따라야 할 것이다.. 즉, 제품디자인의 결정요인 분석결과는 QFD의 접근방법에, 제품 디자인 파급효과 분석결과는 컨조인트 분석에 각각 보완적 기여를 할 수 있다. 이와 동시에, 실증적 분석결과는 Ettlie(1997)의 디자인 통합(DI) 이론에 대한 실증적 기반을 제공할 수 있다. 마지막으로, 성공적인 디자인 경영(DM)을 위해서는 최고 경영자의 지원뿐만 아니라 부처 간 의사소통의 장애요인을 제거하고 CFT(cross-functional team)를 운영함으로써 동시적 엔지니어링(CE) 및 제품 및 공정 디자인의 개발이 제품 개발의 속도를 가속화하고 디자인 품질을 높이며 시장 성공을 보증할 수 있도록 해야 한다.임과 채팅은 긍정적인 상호관련을

• Current Research on Agriculture and Life Sciences
• /
• 제3권
• /
• pp.158-165
• /
• 1985

본(本) 연구(硏究)는 mouse의 육종(育種) 개량(改良)에 필요(必要)한 기초자료(基礎資料)를 얻기 위하여 mouse 4계통(系統) (BALB/c, CBA, C3H, C57-BL)을 양면교잡(兩面交雜)시켜 생산(生産)된 362두(頭)를 공시(供試)하여 평균능력(平均能力), 잡종강세(雜種强勢), 유전변이(遺傳變異) 등(等)을 추정(推定)한 것이다. 공시(供試)된 mouse는 1984년(年) 11월(月)부터 1985년(年) 2월(月)까지 4개월간(個月間) 경북대학교(慶北大學校) 농과대학(農科大學) 부속동물사육장(附屬動物飼育場)에서 사육(飼育)되었으며, 산자수(産仔數), 성비(性比), 생시체중 및 21일령(日齡) 체중과 이유율(離乳率) 등(等)을 조사(調査)하였고 각(各) 형질(形質)에 대(對)한 유전분석(遺傳分析)은 Hayman(1954a, 1954b)의 모형(模型)을 이용(利用)하여 유전변이(遺傳變異)를 추정(推定)하였는데 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 평균능력(平均能力)에 있어서 산자수(産仔數)는 7.54두(頭), 생시(生時) 체중은 1.55g, 21 일령(日齡), 체중은 10.45g, 성비(性比)는 수컷이 53.2%로 많았으며, 전체 이유율(離乳率)은 94.13%로 나타났다. 2. 잡종강세(雜種强勢)의 크기는 산자수(産仔數)에서 6.97%, 생시(生時) 체중에서 6.08% 및 21 일령((日齡) 체중에서는 3.54%로, 성비(性比)는 7.26% 그리고 이유율(離乳率)에서는 2.05%로 나타났다. 3. 산자수(産仔數), 성비(性比), 생시(生時) 체중, 이유시(離乳時) 체중 및 이유율(離乳率) 등(等)의 형질(形質)에 있어서 상가적(相加的) 유전자(遺傳子)의 효과(效果)는 인정(認定)되지 않았다. 우성(優性) 효과(效果)는 산자수(産仔數)와 이유시(離乳時) 체중에서만 나타났는데 산자수(産仔數)에서는 각(各) 교배조합(交配組合)에 따른 우성효과(優性效果)였고 이유시(離乳時) 체중에 있어서는 parental 계통(系統)의 평균(平均) 우성효과(優性效果)였다. 모체효과(母體效果)는 생시(生時) 체중과 이유시(離乳時) 체중에서만 나타났고, 이유시(離乳時) 체중에 있어서는 상반교잡(相反交雜) 효과(效果)도 인정(認定)되었다.

• 한국가정과교육학회지
• /
• 제32권2호
• /
• pp.141-157
• /
• 2020

이 연구는 우리나라의 초등학교 및 중등학교에서 전개되고 있는 학교 인구교육을 전반적으로 검토하기 위해 국가수준의 총론 및 각론 수준의 교육과정 문서에 대한 내용분석을 실시하였고, 그 결과에 터하여 학교 인구교육의 미래 방향을 도출하는데 연구의 목적을 두었다. 그 결과, 2007 개정 교육과정과 2009 개정 교육과정에는 총론 교육과정의 '범교과학습주제'로 저출산·고령사회 대응의 인구교육 내용이 반영되어 있었으나, 현행의 2015 개정 교육과정에는 반영되어 있지 않았다. 각론 교육과정 분석의 결과(제7차 교육과정에서 제안한 '국민공통기본교육과정'에 해당하는 10개의 공통 교과 교육과정 문서 분석함), 중등의 기술·가정교과의 가정과 교육과정, 그리고 초등 및 중등의 사회과 교육과정에서만 교과의 성격이나 목표, 또는 내용요소나 성취기준에 저출산·고령사회 대응의 인구교육 내용이 반영되어 있었다. 교육과정 분석 결과를 바탕으로 다음의 5가지 학교 인구교육의 방향을 도출하였다. 첫째, 학교 인구교육의 목적은 출산에 개입하는 것이 아님을 분명하게 확인하며, '저출생·초고령사회 대응'의 양성평등한 용어를 적용한다. 둘째, 인구교육을 교과의 목표와 내용요소, 그리고 성취기준으로 직접 다루는 교과에 인구교육의 주도교과로서 사명을 부여한다. 셋째, 융합학문적 특성의 인구교육을 융합교육의 적극적 소재로 활용한다. 넷째, 선택중심의 교육과정이 적용되는 고등학교에서는 인구교육의 주요 내용을 다루는 주도교과의 선택을 정책적으로 지원해준다. 다섯째, 교원의 인구 인식을 향상시키기 위한 교사교육을 강화한다. 민주시민의 역량은 사회의 기본적 집단인 가족의 사회화를 통해 출발한다는 점을 고려하면, 삶을 기반으로 하는 가정과교육에서 인구교육을 주도하여 삶, 즉 생활과 연계된 실천적 인구교육으로 학교 사회에 인구교육이 확대되는 데 기여할 수 있을 것이다. 이처럼 학교 인구교육의 주도교과로서의 사명을 가정과교육에 맡겨서 이를 잘 수행해 내도록 하기 위해서는, 우리나라의 전체 교육과정에서 가정과교육의 이수를 강화시키는 교육정책이 뒷받침되어야 할 것이다.