• ETRI Journal
• /
• v.32 no.4
• /
• pp.618-621
• /
• 2010

A low cross-polarization broadband stacked patch antenna is proposed. By means of the stacked patch configuration and probe-fed strip feed technique, the VSWR 1.2:1 bandwidth of the patch antenna is enhanced to 22% from 804 MHz to 1,002 MHz, which outperforms the other available patch antennas (<10%). Furthermore, the antenna has a cross-polarization level of less than -20 dB and a gain level of about 9 dBi across the operating bandwidth. Simulation results are compared with the measurements, and a good agreement is observed.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.312-318
• /
• 2010

A small reconfigurable patch antenna is proposed to achieve polarization diversity for digital multimedia broadcasting systems at 2.6 GHz. To obtain polarization diversity, a pair of on-slit PIN diodes is inserted in each diagonal of a cross-shaped patch. Thus, four PIN-diodes on these slits are utilized to change the connection of the slits and thus achieve polarization. Bias circuits for the diodes are allocated in the cutting corner of the cross-shaped patch to minimize the antenna size. The antenna produces left-hand circular polarization, right-hand circular polarization, or linear polarization, depending on the PIN-diode status. Analysis of circular polarization operation is explicated. Measurements show a gain of about 1.5 dB, a cross polarization of about -20 dB, and an axial ratio of about 2.5 dB.

• Transactions of Materials Processing
• /
• v.24 no.5
• /
• pp.368-374
• /
• 2015

Hydroforming of a non-axisymmetric thin-walled tubular component with variable cross sections was analyzed. In order to solve the sealing problem which occurred due to the thin and non-axisymmetric shape, the use of a lead patch on the punch, which had been successful in hydroforming of thin tubes, was evaluated. A lead patch was attached to the punch to solve the sealing problem, which was caused by the stress gradient in the non-axisymmetric shape. FEM and experiments were also performed to analyze these sealing problems associated with the punch shape and non-axisymmetric shape. Finally, the lead patch was attached at tube surface where intensive local strain concentration would occur to enhance the hydroformability. These methods were successfully used to fabricate non-axisymmetric thin-walled tubular component with variable cross sections that had previously failed during traditional hydroforming.

• Structural Engineering and Mechanics
• /
• v.57 no.2
• /
• pp.295-313
• /
• 2016

In this study, the three-dimensional finite element method is used to determine the stress intensity factor in Mode I and Mixed mode of a centered crack in an aluminum specimen repaired by a composite patch using contour integral. Various mesh densities were used to achieve convergence of the results. The effect of adhesive joint thickness, patch thickness, patch-specimen interface and layer sequence on the SIF was highlighted. The results obtained show that the patch-specimen contact surface is the best indicator of the deceleration of crack propagation, and hence of SIF reduction. Thus, the reduction in rigidity of the patch especially at adhesive layer-patch interface, allows the lowering of shear and normal stresses in the adhesive joint. The choice of the orientation of the adhesive layer-patch contact is important in the evolution of the shear and peel stresses. The patch will be more beneficial and effective while using the cross-layer on the contact surface.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.6
• /
• pp.897-903
• /
• 2002

In this paper, a modified feeding structure for microstrip patch antenna is suggested for improving the performances. The proposed antenna has a gap between the transmission line and the recessed part of the radiating patch which makes a capacitive coupling. It shows higher 511(-l4dB) and lower cross polarization level(-2OdB) compare with the conventional inset ftd patch antenna while having a similar characteristics in another evaluating items. Experimental results are examined and considered to apply to the S-Band application, and the effectiveness has been confirmed by FDTD simulation and measurement simultaneously.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.156-161
• /
• 2006

In this paper, an E-patch antenna on the U-shaped ground plane is designed and experimental studied. In order to reduce to cross-polarization level and to enhance the gain of the microstrip patch antenna, a U-shaped ground plane is employed in the microstrip patch antenna. As a main radiator, an E-shaped patch is used to reduce the antenna size as small as possible. Also to enhance the bandwidth of the antenna, a substrate of the lowest permittivity of which thickness as thick as possible is used and a rectangular patch is overlaid on the air substrate of the E-shaped patch antenna. The radiation characteristics of the antenna are calculated by CST Microwave Studio 5.0 simulation software. Experimental results show that by increasing the height of the sidewall of the ground plane, the antenna gain is increased and the cross-polarization level is decreased.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.479-488
• /
• 2003

Dual-band microstrip antenna is designed for industrial-scientific-medical(ISM) band of 2.4 GHz and 5.8 GHz using finite-difference time-domain method(FDTD). Cross patch 130 by aperture in the ground plane of microstrip line is proposed as radiation element of antenna which is 2 rectangular patch is overlapped. To design antenna, change of input impedance is examined by length change of aperture and stub. And center frequency and - 10 dB bandwidth are investigated by change of length and width in radiation element. Measured result about reflection loss confirm that agree well with simulation results of FDTD and IE3D. And 3 dB beam width, front to back ratio and maximum gain is presented by measuring radiation pattern of antenna in frequency 2.43 GHz and 5.79 GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3A
• /
• pp.166-170
• /
• 2003

In this paper, the characteristics of Koch island microstrip patch antenna are investigated by numerical and experimental methods. The Koch patch is fractal shaped antenna which can be characterized by two properties such as space-filling and self-similarity. Due to its space-filling property of fractal structure, the proposed Koch fractal patch antennas are smaller in size than that of conventional square patch antenna. From numerical and experimental results, it is found that as the iteration number and iteration factor of Koch patch increase, its resonance frequency becomes lower than that of conventional patch, thus contributes to antenna size reduction. In particular, when the fractal iteration factor is 1/4, the fractal antenna is 45% smaller in size than that of conventional patch, while maintaining radiation patterns comparable to those of rectangular antenna and cross polarization level is about -20~-14 dB.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.241-245
• /
• 2002

Dual-band microstrip antenna is designed for industrial-scientific-medical(ISM) band of 2.4㎓ and 5.8㎓ using finite-difference time-domain method(FDTD). Cross Patch fed by aperture in the ground plane of microstrip line is proposed as radiation element of antenna, which is 2 rectangular Patch is overlapped. To design antenna, change of input impedance by aperture and stub length change is examined. And it is investigated that center frequency and -10 ㏈ bandwidth by Length of radiation element and width change. Experimental result about reflection Loss confirmed that agree well with analysis results of FDTD and IE3D, And -3 ㏈ beam width, front to back ratio and gain in frequency 2.43㎓ and 5.79㎓ is presented by measuring radiation Pattern of antenna.

• Biomedical Science Letters
• /
• v.11 no.2
• /
• pp.103-108
• /
• 2005

2-Deoxyribonolactone (dL) arises as a major DNA damage induced by a variety of agents, involving free radical attack and oxidation of C1'-deoxyribose in DNA. We investigated whether dL lesions can be repaired in mammalian cells and the mechanisms underlying the role of DNA polymerase $\beta$ in processing of dL lesions. Pol $\beta$ appeared to be trapped by dL residues, resulting in stable DNA-protein cross-links. However, repair DNA synthesis at site-specific dL sites occurred effectively in cell-free extracts, but predominantly accompanied by long-patch base excision repair (BER) pathway. Reconstitution of long-patch BER demonstrated that FEN1 was capable of removing the displaced flap DNA containing a 5'-dL residue. Cellular repair of dL lesions was largely dependent on the DNA polymerase activity of Pol $\beta$. Our observations reveal repair mechanisms of dL and define how mammalian cells prevent cytotoxic effects of oxidative DNA lesions that may threaten the genetic integrity of DNA.