• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.1
• /
• pp.42-45
• /
• 2014

Even though to discard the waste FRP (Fiber-Reinforced Plastic) is urgent and problematic, the way to do it has not been efficient. In our project team the FRP have been splitted into some layers which have different physical properties; mat and roving layers. Among those, the roving layer woven like a basket by bundles of glass fibers has been cut into reusable fibers called 'F-fiber'. F-fiber is 1 mm or 3 mm in width and 3 cm in length. It is used in fiber-reinforced concrete (FRC) with 0.5%, 0.7%, 1.0%, or 1.5% of volume ratio. Produced FRC was tested in compressive, tensile, and bending stress in contrast to the without-fiber (standard) concrete and 0.1% polypropylene reinforced concrete (PP-FRC). The tensile and bending stresses are more or less those of PP-FRC. The compressive stress, however, is similar (with 3 mm F-fiber) to or lower (with 1 mm F-fiber) than that of standard concrete. Conclusively the usage of the waste FRC in concrete is advised to be limited to the one where the compressive stress is not much critical.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5622-5632
• /
• 2011

This paper presents the simulation design and analysis of Integrated Logistics System(ILS) which is operated by using the AGV(Automated Guided Vehicle). To maximize the operation performances of ILS with AGV, many parameters should be considered such as the number, velocity, and dispatching rule of AGV, part types, scheduling, and buffer sizes. We established the design of experiment in a way of Orthogonal Array in order to consider (1)maximizing the throughput; (2)maximizing the vehicle utilization; (3)minimizing the congestion; and (4)maximizing the Automated Storage and Retrieval System(AS/RS) utilization among various critical factors. Furthermore, we performed the optimization by using the simulation-based analysis and Evolution Strategy(ES). As a result, Orthogonal Array which is conducted far fewer than ES significantly saved not only the time but the same outcome when compared after validation test on the result from the two methods. Therefore, this approach ensures the confidence and provides better process for quick analysis by specifying exact experiment outcome even though it provides small number of experiment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.717-722
• /
• 2016

In this paper, in order to support the peak current limiting function depending on the intensity of the fault current at the early stage of failure, a two magnetically coupled type superconducting fault current limiter (SFCL) is proposed, which includes high-Tc superconducting (HTSC) element 1, where the existing primary and secondary coils are connected to one iron core in parallel, and HTSC element 2, which is connected to the tertiary winding using an additional iron core. The results of the experiments in this study confirmed that the two magnetic coupling type SFCL having coil 1 and coil 2 connected in parallel using dual iron cores is capable of having only HTSC element 1 support the burden of the peak current when a failure occurs. The reason for this is that although HTSC element 1 was quenched and malfunctioned because the instantaneous factor of the initial fault current was large, the current flowing to coil 3 did not exceed the critical current, which would otherwise cause HTSC element 2 to be quenched and not function. In order to limit the peak current upon fault through the sequential HTSC elements, the design should allow it to have the same value as the low value of coil 1 while having coil 3 possess a higher self-inductance value than coil 2. In addition, a short-circuit simulation experiment was conducted to examine and validate the current limiting and recovery characteristics of the SFCL when the winding ratio between coil 1 and coil 2 was 0.25. Through the analysis of the short-circuit tests, the current limiting and recovery characteristics in the case of the additive polarity winding was confirmed to be superior to that of the subtractive polarity winding.

• 대한공업교육학회지
• /
• v.31 no.2
• /
• pp.111-127
• /
• 2006

The purpose of this study is to analyze current recruiting examination and to categorize and construct test item that assess a variety of Mechanic Metal teachers in technical high school for appointing new Mechanic Metal teacher. The future developmental directions in this study are as follows: First, the examination for appointing secondary school new Mechanic Metal Teacher reflects the curriculum of the teacher education and technical high school, must be nomalize. Second, the rational readjustment of the basic necessary subjects for Machinery Metal recruiting examination is required. Third, the Mechanic Metal recruiting examination must prepare the criteria for the domain ratio of presenting problems and improve with level of presenting the question items which demands a knowledge, application and critical thinking. Fourth, in order to avoid the bias of the some subject tendency with committee making questions of different domain, more participation of a committee making questions is required. Fifth, the practical evaluation must be executed by the effective method to be able to make up for the limit of paper and pencil tests Sixth, as the long-term prospect to secure the professionalism of teacher, the recruiting examination of teachers must be carried out with the Machinery and Metal subject, respectively.

• Resources Recycling
• /
• v.18 no.2
• /
• pp.39-50
• /
• 2009

Portland cement production is under critical review due to high amount of $CO_2$ gas released to the atmosphere. Attempts to increase the utilization of fly ash, a by-products from thermal power plant to partially replace the cement in concrete are gathering momentum. But most of fly ash is currently dumped in landfills, thus creating a threat to the environment. Many researches on alkali-activated concrete that does not need the presence of cement as a binder have been carried out recently. Instead, the source of material such as fly ash, that are rich in Silicon(Si) and Aluminium(Al), are activated by alkaline liquids to produce the binder. Hence concrete with no cement is effective in the reduction of $CO_2$ gas. In this study, we investigated the influence of the compressive strength of mortar on alkaline activator and curing condition in order to develop cementless fly ash based alkali-activated concrete. In view of the results, we found out that it was possible for us to make alkali-activated mortar with 70MPa at the age of 28days by using alkaline activator manufactured as 1:1 the mass ratio of 9M NaOH and sodium silicate and applying the atmospheric curing after high temperature at $60^{\circ}C$ for 48hours.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.241-241
• /
• 2007

We fabricated SmBCO coated conductors(CCs) on IBAD-MgO templates using co-evaporation method. IBAD-MgO templates consist of PLD-LMO/epi-MgO/IBAD-MgO/Ni-alloy and showed good in-plane texture of below FWHM 7 degree. Evaporation rates of Sm, Ba, and Cu were precisely controlled to get the optimum composition ratio after deposition process. To optimize the oxygen partial pressure of reaction region, wide range of the partial pressure was investigated from 1 mTorr to 15 mTorr. By reducing the oxygen partial pressure to 5mTorr, (103)grains in SmBCO layer have been increased. On the other hand, there were only (001)grains in SmBCO layer deposited at 15 mTorr $O_2$. Deposition temperature was also investigated from $600^{\circ}C\;to\;800^{\circ}C$ to make high Ic SmBCO CCs. SmBCO on IBAD MgO template showed that the Ic increased gradually at higher growth temperature to $800^{\circ}C$, which the highest Jc and Ic is $2.6\;MA/cm^2$ and 500 A/cm-w., respectively.

• Journal of Trauma and Injury
• /
• v.21 no.1
• /
• pp.36-45
• /
• 2008

Purpose: We conducted this retrospective epidemiological study to assess the incidence and severity of lower extremity injuries in Korea Methods: For this study, we retrospectively reviewed nationwide lower-extremity injury data compiled from 2001 to 2003 based on the National Injury Database, what included National Health Insurance Corporation (NHIC), Car Insurance, and Industry Insurance data. Data were standardized in terms of demographic characteristics, region, and socioeconomic status by using NHIC data. To assess the degree of the injuries, we used the Modified Abbreviated Injury Scale (MoAIS), what has been changed from the International Classification of Disease-10 (ICD-10) code. By using the Excess Mortality Ratio-adjusted Injury Severity Score (EMR-ISS), we classified the degree of severity into four categories: mild, moderate, severe and critical. Results: From 2001 to 2003, lower extremity injuries increased slightly, with a yearly average of 2,437,335. Insurance data should that lower-extremity injuries were the most common, followed by upper-extremity injuries. Significant difference were seen in the numbers of lower extremity injuries based on gender and age. As for provinces, Seoul and Gyeongi provinces had the highest numbers of cases. Junlabukdo had the highest rate of 55,282 cases per 1 million people for standardized gender and population. The annual incidence of the insured patients with lower extrimity injuries was higher than the employer's medical insurance contributions to the medical insurance program. Daily cases occur most often in May and June, with the lowest occurrences being in January and February. Conclusion: The result of this study shows that lower extremity injuries comprised common cause of all injuries. In addition, differences associated with gender, location and socioeconomic status were observed. Further studies are needed to find reasons and then this knowledge will allow strategies to prevent the lower extremity injuries.

• Journal of Korean Society of Transportation
• /
• v.33 no.6
• /
• pp.584-597
• /
• 2015

A considerable amount of literature has been published on pedestrian LOS. So far, however, there is a limitation that LOS analysis methodologies has concentrated on quantitative variables such as pedestrian flow rate, speed and space. This paper intended to suggest the accessibility variable which can not be considered on previous study. The factor was defined and quantified using public transport attributes in particular. This study was carried out in three phases: 1. defined accessibility employing public mode location and service information. 2. investigated the relationship between accessibility and pedestrian flow rate 3. developed the model to establish the factors affected to pedestrian LOS. The results showed that accessibility, walkway attribute and land use type affected the pedestrian LOS. Especially, accessibility and commercial area ratio had negative relationship with LOS. Futhermore, pedestrian LOS declined when obstacle of bus station located on the walkway. On the contrary, LOS was upgraded when sufficient effective width or residential area was secured. These results can receive considerable critical attentions related to determination of pedestrian LOS or effective walkway width.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.81-81
• /
• 2013

반도체, LCD, MEMs 등 미세 전자소자의 제작과 깊은 관련이 있는 IT 산업은 자동차 산업과 함께 세계 경제를 이끌고 있는 핵심 산업이며, 그 발전 가능성이 크다고 할 수 있다. 이 중 반도체, LCD 공정 기술에 관해서 대한민국은 세계를 선도하여 시장을 이끌어 나가고 있는 실정이다. 이들의 공정기술은 주로 높은 수율(yield)을 기반으로 한 대량 생산 기술에 초점이 맞추어져 있기 때문에, 현재와 같은 첨예한 가격 경쟁력이 요구되는 시대에서 공정 기술 개발을 통해 수율을 최대한으로 이끌어 내는 것이 현재 반도체를 비롯한 미세소자 산업이 직면하고 있는 하나의 중대한 과제라 할 수 있다. 특히 반도체공정에 있어 발전을 거듭하여 현재 20 nm 수준의 선폭을 갖는 소자들의 양산이 계획 있는데 이와 같은 나노미터급 선폭을 갖는 소자 양산과 관련된 CD (critical dimension)의 감소는 공차의 감소를 유발시키고 있으며, 패널의 양산에 있어서 생산 효율 증가를 위한 기판 크기의 대형화가 이루어지고 있다. 또한, 소자의 집적도를 높이기 위하여 높은 종횡비(aspect ratio)를 요구하는 공정이 일반화됨에 따라 단일 웨이퍼 내에서의 공정의 균일도(With in wafer uniformity, WIWU) 및 공정이 진행되는 시간에 따른 균일도(Wafer to wafer uniformity)의 변화 양상에 대한 파악을 통한 공정 진단에 대한 요구가 급증하고 있는 현실이다. 반도체 및 LCD 공정에 있어서 공정 균일도의 감시 및 향상을 위하여 박막, 증착, 식각의 주요 공정에 널리 사용되고 있는 플라즈마의 균일도(uniformity)를 파악하고 실시간으로 감시하는 것이 반드시 필요하며, 플라즈마의 균일도를 파악한다는 것은 플라즈마의 기판 상의 공간적 분포(radial direction)를 확인하여 보는 것을 의미한다. 현재까지 플라즈마의 공간적 분포를 진단하는 대표적인 방법으로는 랭뮤어 탐침(Langmuir Probe), 레이저 유도 형광법(Laser Induced Fluorescence, LIF) 그리고 광섬유를 이용한 발광분광법(Optical Emission Spectroscopy, OES)등이 있으나 랭뮤어 탐침은 플라즈마 본연의 상태에서 섭동(pertubation) 현상에 의한 교란, 이온에너지 측정의 한계로 인하여 공정의 실시간 감시에 적합하지 않으며, 레이저 유도 형광법은 측정 물질의 제한성 때문에 플라즈마 내부에 존재하는 다양한 종의 거동을 살필 수 없다는 단점 및 장치의 설치와 정렬(alignment)이 상대적으로 어려워 산업 현장에서 사용하기에 한계가 있다. 본 연구에서는 최소 50 cm에서 최대 400 cm까지 플라즈마 내 측정 거리에서 최대 20 mm 공간 분해가 가능한 광 수광 시스템 및 플라즈마 공정에서의 라디칼의 상태 변화를 분광학적 비접촉 방법으로 계측할 수 있는 발광 분광 분석기를 접목하여 플라즈마 챔버 내의 라디칼 공간 분포를 계측할 수 있는 진단 센서를 고안하고 이를 실 공정에 적용하여 보았다. 플라즈마 증착 및 식각 공정에서 형성된 박막의 두께 및 식각률과 공간 분해발광 분석법을 통하여 계측된 결과와의 매우 높은 상관관계를 확인하였다.

• Korean Journal of Weed Science
• /
• v.8 no.1
• /
• pp.28-32
• /
• 1988

The effects of standing water and cultivation frequency on emergence of Echinochloa glabrescens Munro ex. Hook were determined at varied seeding methods under simulated field conditions for 4 months. In soil-incorporated seeding method total emergence for 4 months was highest in saturated condition followed by 4, 2, and 8cm standing water, whereas total emergence of seeds sown at the soil surface was highest at 2cm standing water followed by 4cm, saturated soil, and 8cm standing water. Within 2 weeks the emergence was highest at 4cm and lowest at 2cm standing water with the soil-incorporated seeding, but the seeds sown at the soil surface with 2cm standing water resulted in the highest emergence. Ratio of emergence within 2 weeks over total emergence during 4 months was lowest at 2cm standing water in the soil incorporation, indication that 2cm standing water would be the critical water level for E. glabrescens. Since most of the seedling was emerged within 2 weeks just before cultivation, the emergence pattern was little affected by cultivation at each standing water level.