• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.963-968
• /
• 2006

The main purpose of this paper is to investigate the stability of water tower with a relatively small footing. The water tower is modeled that the column carrying a container is supported by a rotational spring at the base and is of constant cross-section, with a weight per unit length of column axis. The column model is based on the Bernoulli-Euler beam theory. The Runge-Kutta method and Determinant Search method are used to perform the integration of the governing differential equation and to determine the critical values(critical own weight. and critical buckling load), respectively. The critical buckling loads are calculated over a range of system parameters: the rotational stiffness parameter, the dimensionless radius of container and the own weight parameter of the column. The relation between the rotational stiffness parameter and the critical own weight parameter of the column is analyzed.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.162-168
• /
• 2007

The critical speed above which the vehicle become unstable should be fundamentally verified in the development of new train. In case of high speed tilting train, which require both higher critical speed and higher curving speed, the critical speed should be more carefully treated because the both requirements are conflicting each other in the conventional train design. This research has been performed to estimate the linear and non-linear critical speed of 200km/h Korean Tilting Train which has been developing. The newly developed self-steering mechanism was attached to the tilting train to secure critical speed under the lower yaw stiffness which was inevitable to secure higher curving performance. The simulation to predict critical speed was done by commercial vehicle dynamic S/W. Full scale roller rig test was carried out for the validation of numerical results and effectiveness of self-steering mechanism.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.3 s.108
• /
• pp.247-254
• /
• 2006

This paper (Part II) provides the application results of the method presented in a companion paper (Part I) where the dynamic equation for rotating polar orthotropic disk is formulated and its solution method is considered. The natural frequencies and critical speed of polycarbonate CD are calculated to validate the present method and are shown to by very accurate. The critical speeds of typical GFRP and CFRP CD's are computed by aligning the fibers in radial and circumferential directions. The radially reinforced CFRP CD is shown to have the five times higher critical speed than that of the polycarbonate CD. The natural frequencies and critical speeds of disks with various elastic modulus ratios are obtained. The results show that the radially reinforced disk is more effective in increasing critical speed than the circumferentially reinforced disk.

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.14-19
• /
• 1999

Measurements across single grain boundaries in YBCO thin films and bulk bicrystals have been used to demonstrate the influence of grain boundary structure on the critical current carried across the grain boundary. In particular, we show that one role of grain boundary structure is to change the degree of pinning along the boundary, thereby influencing the critical current. This effect can be used to explain the large difference in critical current density across grain boundaries in thin films compared to that for bulk bicrystal. These differences illustrate the distinction between the intrinsic mechanism of coupling across the grain boundary that determines the maximum possible critical current across a boundary and the measured critical current which is limited by dissipation due to the motion of vortices.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.2
• /
• pp.73-81
• /
• 1999

Shake mixing has been widely used in cell culture. The mixing performance for shake mixing, however, has not been reported quantitatively. The critical circulating frequency and the power consumption for complete suspension of particles, based on the definition of Zwietering, were measured in a shaking vessel containing a solid-liquid system. The critical suspension frequency was correlated by the equation from Baldi's particle suspension model modified with the physical properties of the particles. Critical suspension frequency was correlated as following ; $$N_{JS}={\frac{0.58\;d{_p}^{0.06}(g{\Delta}{\rho}/{\rho}_L)^{0.004}X^{0.03}}{D^{0.35}d^{0.17}{\upsilon}^{0.04}}}$$ The power consumption at the critical suspension condition in the shaking vessel was less than that in an agitated vessel with impeller.

• Journal of Aerospace System Engineering
• /
• v.9 no.1
• /
• pp.1-6
• /
• 2015

A critical speed analysis of oxidizer pump was peformed for a 7 ton class liquid rocket engine as the third stage engine of the Korea Space Launch Vehicle II. Based on the previously developed experimental 30 ton class turbopump and presently developing 75 ton class turbopump for the first and second stage rocket engine of Korea Space Launch Vehicle II, a layout and configuration of the 7 ton class turbopump rotor assembly are determined. A ball bearing stiffness analysis and rotordynamic analysis are performed for both of the bearing unloaded condition and loaded condition. Structural flexibility of the oxidizer pump casing is also included to predict critical speeds. From the numerical analysis, it is confirmed that the rotor system acquires sufficient separate margin of critical speed as a sub-critical rotor even though decrease of critical speed due to the casing structural flexibility.

• Annals of Clinical Neurophysiology
• /
• v.9 no.1
• /
• pp.19-22
• /
• 2007

Critical illness polyneuropathy (CIP) and critical illness myopathy (CIM) occur commonly in the patients who have been on mechanical ventilation for more than 1 week. Even in some patients diagnosed with CIP, an underlying myopathy may be the primary cause of the muscle weakness. The cormorbid status of CIP and CIM is called as critical illness polyneuropathy and critical illness myopathy (CIPNM). We describe a 56-year-old man with acute quadriparesis and areflexia after systemic inflammatory response syndrome. The diagnosis of CIPNM is important to avoid unnecessary investigations and unreasonably pessimistic prognosis. Electrophysiologic studies are essential for the diagnosis and for planning further clinical management.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.792-794
• /
• 2003

AC loss is an important issue in the design of high-$T_c$ superconducting power cables which consist of a number of Bi-2223 tapes wound on a former. In the cables, the tapes have different critical currents intrinsically. And they are electrically connected to each other and current leads. In this work we have prepared a conductor composed of three Bi-2223 tapes with different critical currents. The critical current characteristics in the conductor have experimentally investigated. The results show that for uniform current distributions the conductor's critical current is proportional to the critical current of the Bi-2223 tape to which a voltage lead is attached. However it depends on the current non-uniformity parameter in the conductor rather than the tape's critical currents for nonuniform current distributions.

• Journal of Welding and Joining
• /
• v.1 no.2
• /
• pp.53-60
• /
• 1983

COD test based on fracture mechanics concept was used in this study to evaluate the fracture toughness quantitatively. Effects of specimen sizes on critical COD value for ABS EH 36 steel and its submerged arc weldments, and the variation of critical COD value depending on metallurgical/mechanical heterogeneities caused by weld thermal cycles were investigated. Experiment was performed by using specimens made from base metal and submerged arc weldments according to BS 5762. Obtained results are summarized as follows; 1) Critical COD value for base metal decreases with increasing thickness of specimen. On hand, as the reduction ratio of critical COD decreases with increasing specimen thickness, critical COD value becomes constant above a thickness of specimen. 2) Critical COD value for weldment decreases with increasing thickness of specimen and was also affected by metallurgical states of base metal. 3) Size effects for weldment was greater at the hardened region. 4) Critical COD value was affected by microstructural change due to weld thermal cycles in weldments; that is, accicular ferrite formation is favorable for increasing of COD value.

• Journal of Engineering Education Research
• /
• v.23 no.6
• /
• pp.27-32
• /
• 2020

The aim of this paper is to explore various ways to utilize critical thinking in engineering education. To this end, this paper, in the light of the relationship between critical thinking and the program learning performance of ABEEK, reviews engineering design education, engineering ethics education, and engineering communication education, which are major areas where critical thinking can be utilized in engineering education. As a result, it was confirmed that critical thinking skills, especially the elements and criteria of critical thinking, can contribute to the creative problem-solving process in engineering design education, the rational decision-making process in engineering ethics education, and the effective communication process in engineering communication education.