• Geomechanics and Engineering
• /
• 제18권1호
• /
• pp.71-83
• /
• 2019

This investigation presented conventional triaxial and creep-permeability tests on sandstones considering thermally-induced damage (TID). The TID had no visible effects on rock surface color, effective porosity and permeability below $300^{\circ}C$ TID level. The permeability enlarged approximately two orders of magnitude as TID increased to $1000^{\circ}C$ level. TID of $700^{\circ}C$ level was a threshold where the influence of TID on the normalized mass and volume of the specimen can be divided into two linear phases. Moreover, no prominent variations in the deformation moduli and peak strength and strain appeared as TID< $500^{\circ}C$ level. It is interesting that the peak strength increased by 24.3% at $700^{\circ}C$ level but decreased by 11.5% at $1000^{\circ}C$ level. The time-related deformation and steady-state creep rate had positive correlations with creep loading and the TID level, whereas the instantaneous modulus showed the opposite. The strain rates under creep failure stresses raised 1-4 orders of magnitude than those at low-stress levels. The permeability was not only dependent on the TID level but also dependent on creep deformation. The TID resulted in large deformation and complexity of failure pattern for the sandstone.

• 한국해양공학회지
• /
• 제21권4호
• /
• pp.28-33
• /
• 2007

The objective of this paper is to investigate the relationship between the short-term creep rupture time and the creep rupture properties at three different elevated temperatures in STS304 stainless steel. Uniaxial constant stress creep rupture tests were performed on the steel to observe the creep rupture behaviors at the elevated temperatures of 600, 650 and 700, according to the testing matrix. It is very important to predict creep life in practical creep design problems. As one of the series of studies on the statistical modelling of probabilistic creep rupture time and the development of creep life prediction techniques, the relationship between applied stress and creep rupture behaviors, such as creep strain rate and rupture time, were investigated. In addition, the Monkman-Grant relationship was observed between the steady-state creep rate and the creep rupture time. The creep rupture surfaces observed by SEM showed up dimple phenomenon at all conditions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.245-248
• /
• 2008

콘크리트 구조물은 콘크리트의 크리프와 건조수축 등의 영향으로 시간의존거동을 한다. 그리고 크리프와 건조수축의 불확실성은 매우 크다. 크리프의 불확실성을 줄이기 위해서 실험을 통하여 크리프 특성을 얻는 것이 필요하다. 연구실에서의 실험을 통한 결과를 얻더라도 환경 요인과 모델 자체의 불확실성 등에 의해서 실제 구조물에서는 크리프 특성이 다를 수 있다. 코드식이나 실험에 의해서 얻은 크리프 계수와 실제 구조물에서의 크리프 계수의 실제 물성 차이가 있다면, 구조물의 장기 거동을 적절히 예측하지 못하게 된다. 본 논문에서는 장기거동을 잘 예측하기 위해 시간에 따라 측정된 처짐으로부터 크리프 계수를 추정하였다. RC 빔 부재의 시간에 따른 처짐을 측정한 자료로부터 크리프 계수 민감도 해석을 이용하여 크리프 계수를 추정하고 ACI Committee 209와 CEB-FIP MC90에서 제시하는 크리프 모델에 따른 크리프 계수의 차이를 살펴보았다.

• Journal of Ceramic Processing Research
• /
• 제21권2호
• /
• pp.200-207
• /
• 2020

The self-healing fiber-reinforced composite (abbreviation: shFRC) was made by adding SiC, a self-healing material, between an Al₂O₃ matrix and an Al₂O₃ continuous fiber. shFRC has the characteristic of healing the reduced strength by self-healing. The purpose of this study was to evaluate the damage and healing of new composite material, shFRC, and define new failure criteria. The test method used in this study was a high temperature creep test. The interface fracture behavior with time was investigated by analyzing the creep rate. The creep test conditions were 137 MPa and 150 MPa at 1,000 ℃, and 68.5 MPa, 100 MPa, and 137 MPa at 1,200 ℃, respectively. As a result, the crack propagation of 1,000 ℃ was stopped by healing, and the creep rate was zero. The crack healing part was higher than the strength before the crack formation. Due to the rapid hardening of the interface and the decrease in strength of the fiber, delayed fracture behavior was not observed at 1,200 ℃. If the crack is stopped by self-healing at a constant load, shFRC can use that load stress as the allowable stress. However, when the reaction rate of the interface is markedly rapid, crack propagation is difficult to control.

• Nuclear Engineering and Technology
• /
• 제54권5호
• /
• pp.1570-1578
• /
• 2022

During a severe accident, steam generator (SG) tubes undergo rapid changes in the pressure and temperature. Therefore, an appropriate creep model to predict a short term creep damage is essential. In this paper, a novel creep model for Alloy 690 SG tube material was proposed. It is based on the theta (θ) projection method that can represent all three stages of the creep process. The original θ projection method poses a limitation owing to its inability to represent experimental creep curves for SG tube materials for a large strain rate in the tertiary creep region. Therefore, a new modified θ projection method is proposed; subsequently, a master curve for Alloy 690 SG material is also proposed to optimize the creep model parameters, θ_i (i = 1-5). To adapt the implicit creep scheme to the finite element code, a partial derivative of incremental creep with respect to the stress is necessary. Accordingly, creep model parameters with a strictly linear relationship with the stress and temperature were proposed. The effectiveness of the model was validated using a commercial finite element analysis software. The creep model can be applied to evaluate the creep rupture behavior of SG tubes in nuclear power plants.

• International Journal of Concrete Structures and Materials
• /
• 제5권2호
• /
• pp.97-111
• /
• 2011

Modeling creep of concrete has been one of the most challenging problems in concrete. Over the years, research has proven the significance of creep and its ability to influence structural behavior through loss of prestress, violation of serviceability limit states or stress redistribution. Because of this, interest in modeling and simulation of creep has grown significantly. A research program was planned to investigate the significance of different factors affecting creep of concrete. This research investigation is divided into two folds: first, an in-depth study of the RILEM creep database and development of a homogenous database that can be used for blind computational analysis. Second: developing a probabilistic Bayesian screening method that enables identifying the significance of the different factors affecting creep of concrete. The probabilistic analysis revealed a group of interacting parameters that seem to significantly influence creep of concrete.

• 한국농공학회논문집
• /
• 제54권1호
• /
• pp.19-26
• /
• 2012

Soils exhibit creep behavior in which deformation and movement proceed under a state of constant stress or load. In this study, A series of triaxial tests were performed under constant principal stress in order to interpret the undrained creep characteristics of silty sands. Although samples are non-plastic silty sands, the results of tests show that the creep deformation increasing over time. Based on the results of test, Singh-Mitchell model parameters and Generalized model coefficients were calculated. Generalized model showed slightly larger deformation in the primary creep range but secondary creep deformation was almost identical. Although Singh-Mitchell model showed relatively large errors compared to Generalized model because it uses the average of test results, but Singh-Mitchell model can be easily represented by three creep parameters.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1833-1840
• /
• 2000

Commercially pure copper is tested to obtain creep curves at 2500C. Constitutive relations adopting continuum damage mechanics concept is found to be appropriate to model the creep defor mation up to the tertiary stage. Microscopic observation by SEM reveals that creep condition induces cavities and microcracks subsequently. The constitutive equations along with evaluated creep parameters are implemented into finite element analysis code. The analysis reproduces creep curves under step loading as well as constant loading with reasonable accuracy. Distribution and evolution of damage under creep loading are numerically simulated for two different types of notched specimen. Predicted creep life agrees quite well with rupture test results. The influence of mesh size at notch tip on rupture time prediction is studied, and a degree of refinement is suggested for the specific notched specimens.

• Steel and Composite Structures
• /
• 제19권1호
• /
• pp.111-129
• /
• 2015

This paper first presents an experimental study of twelve specimens for their creep performance, including nine concrete-filled steel tubular (CFST) columns and three plain concrete columns, subjected to three levels of sustained axial loads for 1710 days. Then, the creep strain curves are predicted from the existing creep models including the ACI 209 model, the MC 78 model, and the MC 90 model, and further a fitted creep model is obtained by experimental data. Finally, the creep effects of a CFST arch bridge are analyzed to compare the accuracy of the existing creep models. The experimental results show that the creep strains in CFST specimens are far less than in the plain concrete specimens and still increase after two years. The ACI 209 model outperforms the MC 78 model and the MC 90 model when predicting the creep behavior of the CFST specimens. Analysis results indicate that the creep effects in the CFST arch bridge are significant. The deflections and stresses calculated by the ACI 209 model are the closest to the fitted model in the three existing models, demonstrating that the ACI 209 model can be used for creep analysis of CFST arch bridges and can meet the engineering accuracy requirement when lack of experimental data.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.49-55
• /
• 2020

Creep rupture data for Alloy 690 steam generator tubes in a pressurized water reactor are essentially needed to demonstrate a severe accident scenario on thermally-induced tube failures caused by hot gases in a damaged reactor core. The rupture data were obtained using the tube specimens under different applied-stress levels at 650℃, 700℃, 750℃, 800℃, and 850℃. Important creep constants were proposed using various creep laws in terms of Norton power law, Monkman-Grant (M-G) relation, damage tolerance factor (λ), and Zener-Hollomon parameter (Z). In addition, a creep activation energy (Q) value for Alloy 690 tube was reasonably determined using experimental data. Creep behaviors such as creep strength, creep rates, rupture elongation showed the results of temperature dependence well. Modified M-G plot improved a correlation of the creep rate and rupture life. Damage tolerance factor for Alloy 690 tubes was found to be λ =2.20 in an average value. Creep activation energy for Alloy 690 tube was optimized for Q=350 (kJ/mol). A plot of Z parameter obeyed a good linearity, and the same creep mechanism was inferred to be operative in the present test conditions.