• 한국염색가공학회지
• /
• 제5권4호
• /
• pp.79-91
• /
• 1993

The purpose of this study is to prepare the newer, more comfortable of urea-formaldehyde resin finished fabrics. The methods of this study are by making examinations and comparisons the relations between the thickness, fabrics counts, weight, moisture regain and crease recovery of cotton and viscose rayon fabrics caused by condition of urea-formaldehyde resin finishing and warm retaining ability and warm-cool sense. The analytic results of thermal character in state of fabrics material finished with urea-formaldehyde are as follows: 1. The warm retaining ability has no correlation with mixing ratio of resin but the increase of the warm retaining ability has correlation with the increase of concentration of urea-formaldehyde resin. 2. The result pf multiple regression analysis for effect of physical property according to the concentration of resin to the warm retaining ability revealed as below. As the weight, thickness and density increase and moisture regain decreases, the warm retaining ability increases. 3. The qmax value has no correlation with mixing ratio of resin but the increase of the qmax value has correlation with the increase of resin concentration. In the end, the effect of it promotes cool sense. 4. The result of multiple regression analysis for effect of physical property according to the concentration of resin to the qmax value revealed as below. As he weight and thickness increase, the qmax value decrease. But, as the density and crease recovery increase, the qmax value increase.

• 한국염색가공학회지
• /
• 제9권2호
• /
• pp.41-49
• /
• 1997

To control free formaldehyde release from fabric finished with N-methylol compounds, resin finished cotton fabric was treated with resorcinol solution, dried and cured. Factors affecting to control formaldehyde release have been investigated. It was shown that the aftertreatment with resorcinol greatly suppressed the free formaldehyde release. Up to concentration of about 5% of resorcinol, the concentration of resorcinol effected on the control of free and evolved formaldehyde. And at high concentration of resorcinol, however, the concentration became rather insensitive to contol formaldehyde release. Addition of some salt catalysts such as ammonium chloride, zinc nitrate, sodium acetate and ammonium acetate, was effective in decreasing formaldehyde release. Considering the effect on the control of formaldehyde and crease recovery, ammonium acetate was concidered to be the best catalyst. It was observed that the optimum curing temperature for the resorcinol treatment was about 15$0^{\circ}C$, and that the curing time did not affected formaldehyde release over three minutes. Although the treatment of resorcinol had a little adverse effect on crease recovery of resin finished fabric, this effect could be negligible.

• 한국의류학회지
• /
• 제33권1호
• /
• pp.149-159
• /
• 2009

The purposes of this study are to evaluate physical performance of metallic Jacquard fabrics, and to contribute to the research and development of the women's suit made of the metallic Jacquard fabrics. First, eight fabrics were woven with two kinds of warp yarns(nylon and rayon) and weft yarn blended with various contents(0, 7, 14, 21%) of metallic yarn. Second, the mechanical properties were measured by using the KES-FB system, and physical properties such as tensile strength, tearing strength, abrasion resistance, drape, pilling, snagging, degree of crease resistance, flexural stiffness, specular gloss, folding endurance and electrostatic propensity were measured. The results were as follows. As the metal fiber content increased, bending, shear, thickness and weight increased, which imply low recovery of wrinkles. It means that metallic Jacquard fabrics enable to use as a memory fabric. 7% metallic Jacquard fabric showed a low value at total hand value, but there was little change. As the metal fiber content increased, tensile strength, tearing strength, drape coefficient, specular gloss and flexural stiffness increased, however the degree of crease resistance, electrostatic propensity and folding endurance decreased. The metallic Jacquard fabrics were excellent in snagging, abrasion resistance and pilling.

• 한국염색가공학회지
• /
• 제9권5호
• /
• pp.42-51
• /
• 1997

The purpose of this article is to investigate the effect of $O_{2}$ low temperature plasma treatment oft chitosan treatment of polyester fabrics. Moisture regain, static charge, crease resistance and reduction ratio of the treated fabric were measured. The results of this study were as follows: The add-on ratio and. the moisture regain of polyester fabrics treated with chitosan after treated by plasma(CP PET) were higher than those of polyester fabrics treated with only chitosan(C PET). The static charge of polyester fabrics decreased greatly with increasing the concentration of chitosan. A durability for laundering of CP PET was higher than those of C PET. The crease resistance of polyester fabrics decreased with ihcreasing the concentration of chitosan continuously. CP PET had higher decreasing rate and better durability than C PET. It showed that chitosan-treated polyester fabrics had over 90% reduction ratio after 10 times of laundering, and CP PET had better reduction ratio than C PET.

• 패션비즈니스
• /
• 제5권2호
• /
• pp.67-72
• /
• 2001

Tencel fabric was treated with cellulase and softener. And then Mechanical properties were investigated. Basic characteristic values of clothing wearing were calculated. With the treatment of cellulase and softener treatment, WT, RT, LC, WC, RC of mechanical characteristics were increased, and G, 2HG, 2HG5, B, 2HB were decreased. B/W, $\sqrt[3]{B/W}$, $\sqrt{2HB/W}$, 2HB/B, W/T of Basic characteristic values of clothing wearing were decreased. WC/W, WC/T were increased, Therefore, drapability, crease resistance, pressing softness, air content were improved. In consideration of mechanical characteristics and basic characteristic values of clothing wearing depending on the softener, values of WT, WC/W, WC/T were bigger with the treatment of epoxy and snow softener than with the treatment of cation and blend softener. LC, WC, RC, B/W, $\sqrt[3]{B/W}$, $\sqrt{2HB/W}$, 2HB/B, W/T were bigger with the treatment of cation and blend softener than with the treatment of epoxy and snow softener. Thereofre, with the treatment of epoxy and snow softener, drapability, crease resistance, air content were improved. With the treatment of cation and blend softener, pressing softness were improved.

• 펄프종이기술
• /
• 제42권5호
• /
• pp.31-36
• /
• 2010

When corrugated board is folded at the severely low humidity condition, crack can occur along the scored (or creased) lines of linerboard. This phenomenon is called as score (or crease) crack. It is mainly resulted from the excessive concentration of stress on the outer layer of linerboard. To overcome score crack, many approaches including the installation of constant temperature and humidity system, displacement of low grade raw material by long and strong fibers, or application of water have been tried. We examined the effect of the weight fraction of top layer in two-ply sheet, freeness of top layer stock and wet pressing on strain and elastic modulus of sheet to prevent score crack. Lower freeness and higher press load increased the density and elastic modulus of sheet. Pressing load over the $50kgf/cm^2$, however, decreased the strain of sheet. The weight fraction of top layer had positive effect on strain as well as elastic modulus without increasing the density of sheet.

• 한국정보과학회논문지:시스템및이론
• /
• 제29권4호
• /
• pp.185-191
• /
• 2002

본 연구에서는, 거리 영상에서 mesh를 만들고 그것에서 다양한 LOD(Level of Detail)의 mesh를 생성하는 3차원 물체 LOD 모델링 시스템을 제안하였다. Initial mesh 생성은 마칭 큐브 알고리즘을 사용하였다. 종래의 알고리즘을 다수의 거리 영상에서 효과적으로 mesh를 생성하도록 개선하였다. Base mesh 생성에는 topology를 유지하면서 mesh를 간략화하는 decimation 알고리즘을 사용하였다. 마지막으로 Initial mash와 유사한 새로운 mesh를 생성할 때는 웨이블릿 변환을 적용하여 웨이블릿 개수를 개산하였다. 본 연구에서는 Base mesh를 생성할 때 mesh 간략화 방법을 사용함으로써 웨이블릿 기반의 치명적인 문제인 surface crease 문제를 해결하였다.

• 대한한의학회지
• /
• 제41권4호
• /
• pp.72-77
• /
• 2020

Objectives: This study was carried out to concrete the concept of Hand Gworeum Skin referred in Suwen of Huangdi Neijing. Methods: The Hand Gworeum Meridian was labeled with latex in the body surface of the cadaver, subsequently dissecting a superficial fascia and muscular layer in order to observe internal structures. Results: Skin histologically encompasses a common integument and a immediately below superficial fascia, this study established the skin boundary with adjacent structures such as relative muscle, tendon as its compass. The realm of the Hand Gworeum Skin is as follows: The skin close to the nipple on the 4th intercostal space, the interceps of biceps brachii muscle, the cubital surface at ulnad of bicipital aponeurosis, the anterior surface of the forearm, between flexor carpi radialis and palmaris longus(from wrist crease to 5chon above), the palm between the 3rd and 4th metacarpals on the cross part with the palm crease, the radiod from the middle finger nail(or the end of middle finger). The realm of the Hand Gworeum Skin is situated on between Hand Taeeum Skin and Hand Soeum Skin in front of arm. Conclusion: The realm of Hand Gworeum Skin from the anatomical viewpoint seems to be the skin area outside the superficial fascia or the muscle involved in the pathway of the Hand Gworeum Meridian vessel, Collateral Meridian vessel, and Meridian muscle, being considered adjacent vessels or nerves at the same time.

• Annals of Clinical Neurophysiology
• /
• 제12권2호
• /
• pp.55-60
• /
• 2010

Background: The aim of this study is to identify the correlation between ultrasonographic findings of median nerve and clinical scale and electrophysiologic data in carpal tunnel syndrome. Methods: Forty three patients (79 hands) with electrophysiologically confirmed carpal tunnel syndrome were evaluated. Clinical symptoms were examined by Historical-Objective (Hi-Ob) scale. Electrophysiologic data and Padua scale were used for severity of electrophysiology. In ultrasonographic study, cross sectional area and flattening ratio of median nerve were measured at distal wrist crease level (DWC), 1cm proximal to distal wrist crease level, and 1cm distal to distal wrist crease level. The correlation between Hi-Ob scale, electrophysiologic data and ultrasonography was measured with Spearman rank test. Results: The mean Hi-Ob scale was 2.4. Mean Padua scale was 4.0. In ultrasnonographic study, cross sectional area and flattening ratio were $0.112\;cm^2{\pm}0.025$ and $3.0{\pm}0.6$ at 1cm proximal to DWC level, $0.118{\pm}0.026\;cm^2$ and $2.9{\pm}0.4$ at DWC level, and $0.107{\pm}0.032\;cm^2$ and $3.0{\pm}0.4$ at 1 cm distal to DWC level. Hi-Ob scale was not correlated with cross sectional area and flattening ratio of median nerve. Hi-Ob scale was correlated with Padua scale positively (r=0.44) and correlated with amplitudes of CMAP and SNAP, negatively (r=-0.33; r=-0.30). Cross sectional area of median nerve was significantly correlated with Padua scale, amplitudes and latencies of CMAP and amplitudes of SNAP. Conclusions: Ultrasonographic findings of median nerve and electrodiagnostic data had statistically significant correlation. Consequently, ultrasonography could be an adjunctive method in diagnosis of carpal tunnel syndrome.

• 한국잠사곤충학회지
• /
• 제20권1호
• /
• pp.15-23
• /
• 1978

본 연구는 견직물의 촉감을 손상시키지 않는 범위에서 바람직한 방추성을 보유하는 보다 좋은 요소수지가 공법을 개발하기 위하여 수년간에 걸친 보고이다. 특히 본보고는 요소와 결합하는 폴마린양을 극소화한데 특징이 있고 일반요소수지보다도 더욱 우수성을 보이는 반금속성요소수지(Homo Metalic Urea Resin)을 개발하였다는 사실도 첨가하며 본연구에서 얻어진 결과는 다음과 같다. 1. 본보고에 수록된 요소수지조성은 폴마린함량을 극소화하였고 조성된 수지에서 거의 폴마린냄새를 인정할 수 없을 정도였으며 이전에 보고된 어느 것보다 가장 소량의 폴마린으로 요소수지를 만들었다. 2. 필자가 최초로 만든 화합물 즉 uric zincchloride와 폴마린을 원료로 하여 새로운 반금속성요소수지(Homo Metalic Urea Resin)를 개발하였다. 이 방법은 합성수지처리와 중앙처리를 동시에 할 수 있는 특징이 있다. 3. 위의 두가지 수지처리에서 방추도, 강연도 및 발키네스 등이 증가되었는데 신규개발한 수지가 더욱 좋은 결과를 보였다. 4. 견방사나 저연사견직물이 생사나 고연사손직물의 경우보다 좋은 방추개선을 보였다. 5. 두가지 수지처리법이 모두 실용상의 경제성이 좋았다. 6. 강력과 신도가 수지처리후 다소 저하되었는데 이것은 수지처리로 가교작용과 증량작용이 일어났기 때문이었다. 7. 특수한 요소수지처리방법으로 양모와 유사한 견사제조법도 개발했다. 이 방법은 요소용액에 침지한 생사를 폴마린가스로 충만된 밀실에 방치해 둠으로서 생사표면에 스케일을 발생하게 한 것이다.