• 대한조선학회논문집
• /
• 제49권4호
• /
• pp.327-332
• /
• 2012

International Towing Tank Conference (ITTC) recommended verifying a ship's ability to move transversely at zero forward speed without altering heading by a crabbing test. In sea trial, all available propellers/rudders/thrusters should be used to find the maximum possible transverse speed. For estimating crabbing ability in the design stage, tests to estimate possible swaying force and yawing moment range using all available propellers/rudders/thrusters are conducted. By butterfly diagram, which compares possible swaying force and yawing moment range with external swaying force and yawing moment by wind, a ship's crabbing ability can be estimated. In this study, model tests of a cruise vessel equipped with bow thrusters and POD system were conducted to find out her crabbing ability in the design stage. To mimic quay condition, a model quay-wall was set in the towing tank.

• 대한조선학회논문집
• /
• 제41권1호
• /
• pp.40-46
• /
• 2004

In this paper, one of the harbour manoeuvring tests is described. its goal is to investigate the so-called crabbing performance of ships. By crabbing is meant the ability of the vessel to move sideways with the use of her own manoeuvring devices like propellers, rudders, transverse thruster, etc. The crabbing model tests were carried out in the Ocean Engineering Wide Tank, University of Ulsan(UOU) to measure the transverse forces and yawing moments by the transverse thruster alone and the propeller-rudder arrangement in combination with the bow thruster. The comparison between UOU crabbing test results and data measured at one of foreign research institutes showed a little gap due to different rotating conditions of controllable pitch propellers.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.290-297
• /
• 2004

In this paper, one of the harbour maneuvering tests is described. Its goal is to investigate the so-called crabbing performance of ships. By crabbing is meant the ability of the vessel to move sideways with the use of her own maneuvering devices like propellers, rudders, transverse thruster, etc. the 3m ferry model is made by ocean engineering wide tank in the university of ulsan. when the model ship is leaving and going to the quay, Transverse forces and Yawing moments are measured, in the condition of zero longitudinal force and the design draught, by load cell attached to the longitudinal center of gravity on the ship. the purpose of the experiment is to verify the reliability of ocean wide tank in university of ulsan about crabbing test compared with results of foreign research institute.

• 대한조선학회논문집
• /
• 제57권6호
• /
• pp.345-352
• /
• 2020

This study aims to investigate the crabbing motion of the research vessel "NARA" by full-scale maneuvering trials. The crabbing test method refers to ITTC recommended procedures and guidelines. In order to minimize the fluctuation of the heading angle due to the external force acting on the hull during the pure lateral motion, the tests are conducted using the dynamic positioning system applied to the ship. The test results are analyzed by applying a low-pass filter to remove the noise included in the measurement data. Three conditions are set to define the steady state of crabbing motion. The index to be derived from the crabbing test is quantitatively presented. The ship is confirmed to be capable of the lateral motion of up to 0.844m/s in Beaufort 3.

• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.358-365
• /
• 2021

Crabbing motion is a pure sway motion with only sway velocity. The ship's crabbing motion is essential for an ideal berthing/unberthing process. The unberthing situation proceeds in sequential order such as crabbing motion section, pivoting section, and outer port section. For the berthing situation, the sequence has a reverse order: the inner port section, pivoting section, and crabbing motion section. In this paper, the berthing/unberthing data of the reference ship, Pukyong National University research ship "NARA", was analyzed to develop a sway velocity reference model. Several constraints were defined to derive the crabbing motion section during berthing/unberthing. The sway velocity reference model for the auto-berthing/unberthing was developed using the estimated sway velocity. A reproduction simulation of the ship was performed to compare the designed reference model and the reference ship data.

• 한국해양공학회지
• /
• 제27권6호
• /
• pp.56-64
• /
• 2013

Crabbing motion is the pure sway motion of a ship without surge velocity. Thus, it can be applied to a berthing operation. Crabbing motion is induced by a peculiar operation method called the push-pull mode. The push-pull mode is induced by using a combination of the main propeller and side thruster. Two propellers generating the same amounts of thrust and rotating in opposite directions produce some yawing moment on a vessel but do not induce longitudinal motion. With the additional operation of side thrusters, the push-pull mode is used to induce a large amount of lateral force. In this paper, three-degree-of-freedom equations of motion such as for the surge, sway, and yaw are constructed for the crabbing motion. Based on these equations of motion, a feedback linearization control method is applied to auto-berthing control for a twin-screw ship with side thrusters. The controller can deal with the nonlinearity of a system, which is present in the berthing maneuver of a twin screw ship. A simulation of the auto-berthing of a ship is performed to validate the performance of the designed controller.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.347-360
• /
• 2014

The auto-berthing of a ship requires excellent control for safe accomplishment. Crabbing, which is the pure sway motion of a ship without surge velocity, can be used for this purpose. Crabbing is induced by a peculiar operation procedure known as the push-pull mode. When a ship is in the push-pull mode, an interacting force is induced by complex turbulent flow around the ship generated by the propellers and side thrusters. In this paper, three degrees of freedom equations of the motions of crabbing are derived. The equations are used to apply the adaptive backstepping control method to the auto-berthing controller of a cruise ship. The controller is capable of handling the system non-linearity and uncertainty of the berthing process. A control allocation algorithm for a ship equipped with two propellers and two side thrusters is also developed, the performance of which is validated by simulation of auto-berthing.

• 한국해양공학회지
• /
• 제38권1호
• /
• pp.10-17
• /
• 2024

This study assessed the potential for crabbing motion in waterjet ships by exclusively employing stern thrusters. The theoretical considerations were validated through practical sea trials on the naval vessel PKG (Patrol Killer Guided missile) equipped with three stern thrusters. The control forces were calculated using the force equilibrium equation. The results showed that the hull exhibited rotations and lateral movements under wind influence. The port tail exhibited a leftward turning tendency due to the wind. This phenomenon arises from the dominance of the rotational force generated by the stern thruster over the lateral force exerted by the hull, making it challenging to maintain force equilibrium. In the sea trial, the hull rotated by 10° and moved 10.8 m laterally, with a longitudinal movement of 0.26 m. Remarkably, the lateral movement surpassed the longitudinal displacement, indicating the success of the trial. The substantial lateral travel distance provided tangible evidence that the crabbing motion of the ship is achievable using only stern thrusters. This study contributes valuable insights into enhancing the maneuverability of waterjet ships, offering practical applications for naval operations and maritime activities.