• Tribology and Lubricants
• /
• v.23 no.4
• /
• pp.170-174
• /
• 2007

Wear and scuffing tests were conducted using friction and wear measurement of piston rings and cylinder blocks in low friction diesel engine. The frictional forces, wear amounts and cycles to scuffing in boundary lubricated sliding condition were measured using the reciprocating wear tester. The cylinder blocks were used as reciprocating specimens, and the piston rings with several coatings were used as fixed pin. Several coatings were used such as DLC, TiN, Cr-ceramic and TiAlN in order to improve the tribological characteristics. From the tests wear volume of piston ring surfaces applied various coatings were compared. During the tests coefficients of friction were monitored. Test results showed that DLC coatings showed good tribological properties. TiN and Cr-ceramic coated rings showed good wear resistance properties but produced high friction.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.4
• /
• pp.183-189
• /
• 2012

Surface treatments and their effects on high temperature properties for the Hastelloy X, which is a promising candidate alloy for high temperature heat-transport system, have been evaluated. For TiAlN and $Al_2O_3$ overlay coatings, the two different PVD (physical vapor deposition) methods using an arc discharge and a sputtering, were applied, respectively. In addition, a different surface treatment method of the diffusion coating by a pack cementation of Al (aluminiding) was also adopted in this study. To achieve enhanced thermal oxidation resistance at $1000^{\circ}C$ by suppressing the inhomogeneous formation of thick $Cr_2O_3$ crust at the surface region, a study for the surface modification methods on the morphological and structural properties of Hastelloy X substrates has been conducted. The structural and compositional properties of each sample were characterized before and after heat-treatment at $1000^{\circ}C$ under air and He environment. The results showed that the Al diffusion coating showed the more enhanced high temperature properties than the overlay coatings such as the suppressed thick $Cr_2O_3$ crust formation and lower wear loss.

• Transactions of Materials Processing
• /
• v.23 no.1
• /
• pp.29-34
• /
• 2014

The damage level of the die surface was predicted by estimating the surface roughness with a finite element analysis and the wear characteristics. Wear and friction tests were conducted to compare the wear characteristics for three kinds of surface treatments - CrN, TiAlN and AlCrN coatings. A prediction model was derived from the surface roughness results with respect to contact pressure and sliding speed which were obtained from the wear test. Surface roughness values for the damage regions of the die surface were compared between the experiments and the prediction model, which shows fairly good agreement with each other.

• Journal of the Korean Vacuum Society
• /
• v.15 no.1
• /
• pp.110-116
• /
• 2006

The mechanical property and cutting performance of the cutting tools coated with nanoscale nyktukatered nitride film have been investigated. $Ti_{0.54}Al_{0.46}N-CrN$ and $Ti_{0.84}Al_{0.16}N-NlN$ systems, which showed super-lattice in nanoscale multilayered coating, were deposited on WC-Co insert by UBM sputtering, The superlattice coatings with different bilayer periods were manufactured by controlling deposition parameters. The superlattice formation and hardness of the nanoscale multilayered nitride film and the cutting performance of the insert coated with the film were examined. The hardness and cutting performance were dependent on the bilayer periods of the coatings. The flank wear of the inserts with superlattice coatings were decreased over $20\%$, compared to those of commonly used cutting tools coated with TiAIN single phase.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.06a
• /
• pp.3-3
• /
• 2001

Recently TiN, TiAlN, CrN hardcoatings have adapted many industrial application such as die, mold and cutting tools because of good wear resistant and thermal stability. However, in terms of high speed process, general hard coatings have been limited by oxidation and thermal hardness drop. Especially in the case of PCB drill, high speed cutting and without lubricant process condition have not adapted these coatings until now. Therefore more recently, superhard nanocomposite coating which have superhard and good thermal stability have developed. In previous works, WC-TiAlN new nanocomposite film was investigated by cathodic arc ion plating system. Control of AI concentration, WC-TiAlN multi layer composite coating with controlled microstructure was carried out and provides additional enhancement of mechanical properties as well as oxidation resistance at elevated temperature. It is noted that microhardness ofWC-TiA1N multi layer composite coating increased up to 50 Gpa and got thermal stability about $900^{\circ}C$. In this study WC-TiAlN nanocomposite coating was deposited on PCB drill for enhancement of life time. The parameter was A1 concentration and plasma cleaning time for edge sharpness maintaining. The characteristic of WC-TiAlN film formation and wear behaviors are discussed with data from AlES, XRD, EDS and SEM analysis. Through field test, enhancement of life time for PCB drill was measured.

• International Journal of Ocean System Engineering
• /
• v.2 no.2
• /
• pp.106-115
• /
• 2012

In the present study, TiN and CrN films were coated by arc ion plating equipment onto aluminum alloy substrate, A2024. The film thickness was about 4.65 ${\mu}m$. TiN and CrN films were analyzed by X-ray diffraction and energy dispersive X-ray equipments. The Young's modulus and the micro-Vickers hardness of aluminum substrate were modified by the ceramic film coatings. The difference in Young's modulus between substrate and coating film would affect on the wear resistance. The critical load, Lc, was 75.8 N for TiN and 85.5 N for CrN. It indicated from the observation of optical micrographs for TiN and CrN films that lots of cracks widely propagated toward the both sides of scratch track in the early stage of MODE I. TiN film began to delaminate completely at MODE II stage. The substrate was finally glittered at MODE III stage. For CrN film, a few crack can be observed at MODE I stage. The delamination of film was not still occurred at MODE II and then was happened at MODE III. This agrees with critical load measurement which the adhesive strength was greater for CrN film than for TiN film. Consequently, it was difficult for CrN to delaminate because the adhesive strength was excellent against Al substrate. The wear process, which the film adheres and the ball transfers, could be enhanced because of the increase in loading. The wear weight of ball was less for CrN than for TiN. This means that the wear damage of ball was greater for TiN than for CrN film. It is also obvious that it was difficult to delaminate because the CrN coating film has high toughness. The coefficient of friction was less for CrN coating film than for TiN film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.5
• /
• pp.227-232
• /
• 2012

Inconel 617 and Hastelloy X are the most promising candidate materials for the heat exchanger of next generation nuclear reactor. Surface coating and its effects on high temperature properties for the Inconel 617 and Hastelloy X under molten FLiNaK (LiF-NaF-KF) salt environment have been investigated. For TiAlN and $Al_2O_3$ overlay coatings, the two different PVD (physical vapor deposition) methods of an arc discharge and a sputtering were applied, respectively. A study for the thermal stability of the surface modified Ni-Cr alloy substrates has been conducted. To evaluate the corrosion mechanism of Ni-Cr alloys in the molten salt, a ruptured Inconel pipe used for the molten salt transportation has been analyzed. The thermal properties of morphological and structural properties each sample were characterized before and after heat-treatment at $600^{\circ}C$ in molten FLiNaK salt. The results showed that the TiAlN and $Al_2O_3$ overlay coated specimens had the enhanced high temperature stability.

• Transactions of Materials Processing
• /
• v.31 no.4
• /
• pp.186-193
• /
• 2022

The application of UHSS sheet is being expanded up to 50% to reduce the weight of automobiles and improve safety. However, due to the high strength and low elongation of the ultra-high tensile strength steel sheet, product defects such as spring back and mold defects such as cracks and chippings also occur. In this study, Pin/Ring on Disc and Spiral wear tests were conducted to evaluate the durability of Ti/Cr-coated molds for forming 1.2GPa grade UHSS sheets. Component analysis and thickness were measured for each coating layer, and hardness and adhesion were investigated to determine mechanical properties. Combining the results of various wear tests, it was found that the TiAlN coating had the best wear and sticking resistance.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.4
• /
• pp.170-174
• /
• 2007

High Velocity Oxygen Fuel (HVOF) thermal spray coating of nano size WC-Co powder (nWC-Co) has been studied as one of the most promising candidate for the possible replacement of the traditional hard plating in some area which causes environmental and health problems. nWC-Co powder was coated on Inconel 718 substrates by HVOF technique. The optimal coating process obtained from the best surface properties such as hardness and porosity is the process of oxygen flow rate (FR) 38 FMR, hydrogen FR 57 FMR and feed rate 35 g/min at spray distance 6 inch for both surface temperature $25^{\circ}C\;and\;500^{\circ}C$. In coating process a small portion of hard WC decomposes to less hard $W_2C$, W and C at the temperature higher than its decomposition temperature $1,250^{\circ}C$ resulting in hardness decrease and porosity increase. Friction coefficient increases with increasing coating surface temperature from 0.55-0.64 at $25^{\circ}C$ to 0.65-0.76 at $500^{\circ}C$ due to the increase of adhesion between coating and counter sliding surface. Hardness of nWC-Co is higher or comparable to those of other hard coatings, such as $Al_2O_3,\;Cr,\;Cr_2O_3$ and HVOF Tribaloy 400 (T400). This shows that nWC-Co is recommendable for durability improvement coating on machine components such as high speed spindle.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.3-4
• /
• 1999

최근 산업이 고속도화, 고능률화 및 고정멸화의 추세로 발전함에 따라 우수한 내마모성, 인성, 고온 안정성 및 내구성을 갖는 공구 및 금형을 요구하게 되었다. 그러나 이와같은 성질들은 어떤 단일 재료에서는 얻을 수 없으며 적당한 기판공구나 금혈위에 내마모성 보호피막을 coating함으로 비교적 저렴하게 얻을 수 있다. 화학증착법으로 TiC, TiN등을 증착시킬때에는 $1000^{\circ}C$정도의 반응온도가 필요하며 이러한 증착온도는 모재가 초경합금일때는 문제가 안되나 강재일 경우 모재의 연화와 칫수변화의 문제를 야기시킨다. 최근에는 플라즈마를 사용하여 증착반응온도를 $550^{\circ}C$ 이하로 낮추는 플라즈마 화학 증착볍(PACVD)이 대두되고 있다. 그러나 이 방법어서 는 뚱착하려는 금속원소가 TiCl4의 형태로 공급되고 있으므로 생성된 층이 염소를 포함하고 있다. 이 층에 잔존하는 염소는 층의 기계적 성질을 저하시키고 층내의 stress를 유발시킨다. 또한 HCI개스의 생성으로 인하여 펌프 및 장비의 부식이 촉진 된다 이러한 결점을 극복하기 위하여 금속유기화합물 전구체(metallo-organic precursor)로 $TiCl_4$를 대체하고자 하는 연구가 활발하게 진행되고 있으며 본 연구실에서 이에 대하여 연구한 결과를 소개하고자 한다. diethylamino titanium을 전구체로 사용하여 $H_2,\;N_2,\;Ar$분위기하에서 pulsed d.c.를 사용하는 MO-PACVD에 의하여 $150~250^{\circ}C$의 저온에서 Al 2024 기판에 TiCN층 형 성을 하였다. 전구체 증발온도는 $74~78^{\circ}C$의 온도범위어야 하며 고경도의 코탱층은 54% duty, 14.2kHz, 450V의 조건에서 얻어졌으며 duty, 주파수, 전압이 증가함에 따라 경도는 저하되었다. 이때의 표면 morphology를 SEM으로 조사한바 dome structure가 크게 발달되었음을 알 수 있었다. 본 실험의 온도 범위내에서 얻은 TiCN 증착반응의 활성화에너지는 7.5Kcal/mol이었다. 증착된 TiCN층은 우수한 내마모섣을 나타내었으며 스크래치테스트 결과 17N의 엄계하중을 나타내었다. 본 연구에서 변화 시킨 duty, 주파수, 전압의 범위에서는 층의 밀착력은 크게 변화하지 않았다. titanium isopropoxide를 전구체로 사용하여 Hz, Nz 분위기하에서 d.c.를 사용하는 MO-PACVD에 의하여 Ti(NCO) 코팅층을 SKDll, SKD61, SKH9 공구강에 형성시키는 공정을 개발하였다. 최적의 Ti(NCO) 코탱층을 얻기 위해 유입전구체 부피%의 양은 향착압력의 5%를 넘지 않아야 되고 수소와 젤소 가스비가 1:1일 때 가장 높은 코팅층의 경도값을 나타내었다. 수소와 질소 가스비가 3:7일 때 TiFeCr(NCO)의 복화합물 코팅층이 형성됨을 알 수 있었고 500t의 증착온도에서 얻은 Ti(NCO) 코팅층이 높은 경도값과 좋은 내식성을 나타내었다. 또한 이와같은 Ti(NCO) 코팅공정과 본 실험실에서 개발한 확산층만 형성시키는 plsma nitriding 공정을 결합하여 복합코탱층을 형성하였는데 이 복합코팅층은 고경도와 우수한 내마모성, 내식성 뿐만 아니라 10)N 이상의 뛰어난 밀착력을 나타내었다. 현재 많이 사용되고 있는 PVD법은 step coverage가 좋지 않은 점과 cost intensive p process라는 단점이 있다. MO-PACVD법은 이러한 문제를 해결할 수 있는 방법으로서 앞으로 지속적인 도전이 요구되는 분야이다.