• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.593-597
• /
• 2003

Anodic aluminum oxide (AAO) membrane was made of aluminum sheet (99.6%, 0.2 mm thickness). The regular array of hexagonal nano pores or channels were prepared by two step anodization process. A detail description of the AAO fabrication is presented. After the 1st anodization in oxalic acid (0.3 M) at 45 V, The formed AAO was removed by etching in a solution of 6 wt% $H_3$$PO_4$＋1.8 wt% $H_2$$CrO_4$. The regular arrangement of the pores was obtained by the 2nd anodization, which was carried out in the same condition as the 1st anodization. Subsequently, the alumina barrier layer at the bottom of the channel layer was removed in phosphoric acid (1M) after removing of aluminum. Pore diameter, density, and thickness could be controlled by the anodization process parameters such as applied voltage, anodizing time, pore widening time, etc. The pore diameter is proportional to the applied voltage and pore widening time. The pore density and thickness can be controlled by anodization temperature and voltage.

• Journal of Magnetics
• /
• v.3 no.4
• /
• pp.105-111
• /
• 1998

The low energy excitations of spin waves (SWR) in thin films can be used for determination of the surface anisotropy constant and the nonhomogeneities of magnetization in the close-to-surface layer. The dispersion relation in SWR is sensitive on the geometry of experiment. We report on temperature dependence of surface magnetic anisotropy energy constant in magnetic semiconductor thin films of$ CdCr_{2-2x}In_{2x}Se_4$ at spin glass state. Samples were deposited by rf sputtering technique on Corning glass substrate in controlled temperature conditions. Coexistence of the infinite ferromagnetic network (IFN) and finite spin slusters (FSC) in spin glass state (SG) is know phenomena. Some behavior typical for long range magnetic ordering is expected in samples at SG state. The spin wave resonance experiment (microwave spectrometer at X-band) with excited surface modes was applied to describe the energy state of surface spins. We determined the surface magnetic anisotropy energy constant versus temperature using the surface inhomogeneities model of magnetic thin films. It was found that two components contribute to the surface magnetic anisotropy energy. One originates from the exchange interaction term due to the lack of translation symmetry for surface spin as well as from the originates from the exchange interaction term due to the lack of translation symmetry for surface spin as well as from the stray field of the surface roughness. The second one comes from the demagnetizing field of close-to surface layer with grad M. Both term linearly decrease when temperature is increased from 5 to 123 K, but dominant contribution is from the first component.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.619-623
• /
• 2006

Selective vapor deposition of conductive poly(3,4-ethylenedioxythiophene) (PEDOT), thin films has been carried out on self assembled monolayers patterned oxide substrate. Since the 3,4-ethylenedioxythiophene(EDOT) monomer can be polymerized only in the presence of oxidant such as $FeCl_3$, the PEDOT thin film is selectively deposited on patterned $FeCl_3$, which only adsorbs on the partly removed SAMs region due to the inability of $FeCl_3$ to adsorb on SAMs. Therefore, the partly removed SAMs can act as an adsorption layer for the $FeCl_3$ and also as a glue layer for the deposition of PEDOT, resulting in the significantly increased adhesion of PEDOT to $SiO_2$ substrate. The use of UV lithography and Cr patterned quartz mask provided the formation of SAMs patterns on oxide substrates, which allowed for the selective deposition of conductive PEDOT thin films.$^{oo}The$ new process was successfully developed for the selective deposition of PEDOT thin films on SAMs patterned oxide substrate, providing a new way for the patterning of vapor phase deposition of PEDOT thin films with accurate alignment and addressing the inherent adhesion issues between PEDOT and dielectrics.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3474-3490
• /
• 2021

Sodium-cooled fast reactor (SFR) is the preferred technology of the generation-IV fast neutron reactor, and its core body mainly uses nuclear-grade 316 stainless steel. In order to prolong the design life of SFRs to 60 years and more, it is necessary to summarize and analyze the anti-corrosion effect of nuclear grade 316 stainless steel in high temperature sodium environment. The research on sodium corrosion of nuclear grade 316 stainless steel is mainly composed of several important factors, including the microstructure of stainless steel (ferrite layer, degradation layer, etc.), the trace chemical elements of stainless steel (Cr, Ni and Mo, etc) and liquid impurity elements in sodium (O, C and N, etc), carburization and mechanical properties of stainless steel, etc. Through summarizing and constructing the sodium corrosion rate equations of nuclear grade 316 stainless steel, the stainless steel loss of thickness can be predicted. By analyzing the effects of temperature, oxygen content in sodium and velocity of sodium on corrosion rate, the basis for establishing integrity evaluation standard of SFR core components with sodium corrosion is provided.

• Journal of Korean Society on Water Environment
• /
• v.27 no.3
• /
• pp.300-305
• /
• 2011

This study aimed at analyzing the runoff quality by the layer thickness and material of soil roof to make best use of the rainwater falling on it in terms of safety and efficiency and resulted in the following assessments. It turned out that the concentrations decreased more in T-N, $NO_3$-N, $NH_4$-N, T-P and $PO_4$-P in roof rainwater except 30 cm for the RW1 soil roof after passing through it than those of first rainwater. On the other hand, the concentrations in rainwater passing through gravel roof turned out to be equal or same to those of the first rainwater. As a result of analysis of metallic stuff in runoff, there was no indication of Cd, Cr, Mn and Pb as well. The concentration of Cu, Fe and Zn in rainwater through soil roof became less than that of the first rainwater. In this research, the soil roof showed the good efficiency in lowering the concentration of such components as nitrogen, phosphorus and metals. Based on the results from this work, more practical study would be required further in the future in relation to soil roof when installing the rainwater-utilizing facilities.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.1
• /
• pp.60-67
• /
• 2010

Although several studies have reported that Cr, Cu and As can leach from CCA-treated woods, few studies have been conducted on this topic in Korea. Therefore, this study was conducted to monitor Cr, Cu and As leaching from CCA-treated wood products and to develop a rapid identification method for CCA-treated wood products by using indicators such as PAN stain. Soil samples were collected at depths of 0-70 cm and wood samples were collected by thickness of wood layer. The soil and wood samples were then digested and analyzed for Cr, Cu and As concentrations using an atomic absorption spectrometer. The As and Cu concentrations decreased sharply with depth from 34.38 and 33.65 mg $kg^{-1}$ at 0-1 cm to 1.72 and 7.84 mg $kg^{-1}$ at 70 cm, respectively. In general, As was more mobile than Cr and Cu in the soil. For wood samples, the Cr, Cu and As concentrations were higher in the outer layer (0-0.5cm) than the inner layers (0.6-4.5cm). Evaluation of rapid identification methods revealed that 100% acetone with 0.1% PAN indicator was the best combination for detection of CCA-treated wood in the field.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.11
• /
• pp.46-54
• /
• 1998

A planar Bi-Sb multijunction thermal converter, which is consisted of a linear or bifilar thin film NiCr-heater and a thin film Bi-Sb thermopile, has been fabricated, and its ac-dc transfer characteristics were examined in a frequency range from 10 Hz to 10 KHz. In order to increase the thermal sensitivity and to decrease the ac-dc transfer error of a thermal converter, the heater and the hot junctions of a thermopile were prepared on a Si$_3$N$_4$/SiO$_2$/Si$_3$N$_4$-diaphragm which acts as a thermal isolation layer, and the cold junctions on the Si$_3$N$_4$/SiO$_2$/Si$_3$N$_4$-thin film supported with the silicon rim which functions as a heat sink. The respective thermal sensitivities in air and in a vacuum of the converter with a built-in bifilar heater were about 14.0 ㎷/㎽ and 54.0 ㎷/㎽, and the ac-dc voltage and the current transfer difference ranges in air were about $\pm$0.60 ppm and $\pm$0.11 ppm, respectively, indicating that the ac-dc transfer accuracy of the converter are much higher than that of a commercial 3-dimensional multijunction thermal converter. However, the output thermoelectric voltage fluctuation of the converter was rather high.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.2
• /
• pp.156-160
• /
• 1997

The combination of biological wastewater treatment process and membrane separation has many advantages such as better effluent quality and system stability over the conventional biological wastewater treatment process. In this study, direct membrane separation using nonwoven fabric was applied to biological wastewater treatment. A nonwoven fabric module was submerged in the aerated bioreactor. And accumulated biomass in the bioreactor was separated by suction. The system was operated with various condition to investigate pollutant removal efficiencies and flux. After formation of biomass layer on nonwoven fabric surface, a day, the stable effluent water quality was obtained. The flux decreased at a high suction pressure faster than a low pressure. The stable flux was obtained at the pressure of $21{\sim}25cmHg$. In spite of variation of hydraulic retention time, organic loading rate, the removal efficiencies of BOD, $COD_{Cr}$. $COD_{Mn}$ were very high as follows : $95.2%(0.14{\sim}0.97\;BODKg/m^3/day)$, $86.0%(0.17{\sim}1.39\;COD_{Cr}Kg/m^3/day)$, $90.0%(0.097{\sim}0.61\;COD_{Mn}Kg/m^3/day)$.

• Journal of Korean Ophthalmic Optics Society
• /
• v.9 no.2
• /
• pp.463-471
• /
• 2004

The Fabry-Perot interferometer filters for UV meter were designed using the design program of optical thin films. From the data obtained, two filters were fabricated. The transmittance of two filter were measured by spectrophotometer in order to analysis their optical property. The transmittance was controlled by the thickness of Ag reflector and the wavelength of the transmission was controlled by the thickness of $SiO_2$ spacer. The two UV filters were fabricated by the RF magnetron sputtering which are the multilayers of [air/$SiO_2$(174.6 nm)|Ag(78 nm)|$SiO_2$(68 nm)|Ag(78 nm)|Cr(5 nm)|glass] and [air/$SiO_2$(174.6 nm)|Ag(S8 nm)|$SiO_2$(56 nm)|Ag(58 nm)|Cr(S nm)|glass]. One filter has the maximum transmittance of 6% at the about 370nm and it has the transmittance of below 0.2% at 400nm. The other filter can be found that the transmittance is increased as the thickness of Ag is decreased and the wavelength of the transmission is controlled by the thickness of $SiO_2$ spacer layer.

• Journal of Wetlands Research
• /
• v.13 no.2
• /
• pp.243-263
• /
• 2011

In order to understand the sedimentary environment of the southern intertidal zone of Shihwa Lake, west coast of Gyeonggi-do, 10 surface and 2 core sediment samples were analysed for grain size, water content, AVS (Acid Volatile Sulfide), TOC (Total Organic Carbon), concentrations of metals (Al, Fe, Mn, Cu, As, Pb, Zn, Ni, Cd, and Cr). The surface sediments are generally poorly sorted (0.60~2.31 ${\phi}$) sandy Silt, slightly gravelly muddy Sand, silty Sand, Sand with mean grain size of 2.95 to 6.00 ${\phi}$. The sediments contain Al (1.54%), Fe (1.75%), Cu (9.1ppm), As (1.1ppm), Pb (18.8 ppm), Ni (11.0 ppm), Cd (0.02 ppm), and Cr (30.1 ppm) on the average. Heavy metals are concentrated less than ERL (Effect Range-Low), verified by NOAA (National Oceanic and Atmospheric Administration). In the core sediments, they are also less than the ERL. Based on the uniform vertical distribution of excess radioactivity of $^{210}Pb$, the core sediments seen to have been actively mixed biologically or rapidly deposited after the construction of Shi-Hwa Seawall. The 'enrichment factor' of metals, normalized to Al, shows that the upper sediments of 35 cm in depth are more polluted. infect was significant in 2 core sediment samples in 35 cm below layer.