• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.294-295
• /
• 1997

CO-Cr 수직자기기록 매체의 우수한 하지층을 개발하기 위하여, 스피넬 결점막$(Fe,M)_3O_4$ (M=Ni,Zn)이 스핀스프레이 페라이트 플레이팅 방법으로 유리 기판 위에 제작되었다. 반응액과 산화액은 기판이 회전하는 반응용기로 분사되었다. 반응은 기판의 회전소독, 반응온도, 반응액과 산화액의 유속 그리고 반응액과 산화액의 농도에 의해 영향받았다. 반응액과 산화액의 유속은 60(ml/min)으로 하고, 반응온도는 90[$^{\circ}C$] 그리고 기판의 회전속도는 150[rpm]의 조건하에서, 페라이트 플레이팅 반응에 미치는 반응액과 산화액 농도의 영향이 화학적 조성, 결정학적 및 자기적 특성의 관점에서 연구되었다. $Ni_{0.34}Zn_{0.66}Fe_2O_4$의 조성에서, 우리는 가장 안정한 결정학적 및 자기적 특성을 얻었다.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.5
• /
• pp.339-344
• /
• 2017

Highly corrosion resistance performance of CrAlSiN coatings were obtained by applying ultrathin $Al_2O_3$ thin films using atomic layer deposition (ALD) method. CrAlSiN coatings were prepared on Cr adhesion layer/SUS304 substrates by a hybrid coating system of arc ion plating and high power impulse magnetron sputtering (HiPIMS) method. And, ultrathin $Al_2O_3$ passivation layer was deposited on the CrAlSiN/Cr adhesion layer/SUS304 sample to protect CrAlSiN coatings by encapsulating the whole surface defects of coating using ALD. Here, the high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and energy dispersive X-ray spectrometry (EDX) analysis revealed that the ALD $Al_2O_3$ thin films uniformly covered the inner and outer surface of CrAlSiN coatings. Also, the potentiodynamic and potentiostatic polarization test revealed that the corrosion protection properties of CrAlSiN coatings/Cr/SUS304 sample was greatly improved by ALD encapsulation with 50 nm-thick $Al_2O_3$ thin films, which implies that ALD-$Al_2O_3$ passivation layer can be used as an effect barrier layer of corrosion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.550-552
• /
• 2003

We prepared $Co_{77}Cr_{20}Ta_3$ Magnetic layer for perpendicular magnetic recording media with introduce Two-step methode and Amorphous Si Underlayer on slide glass substrate. The thickness of magnetic layer were 100nm, and Underlayer were varied from 5 to 100 nm. The multi layer Properties of crystal structure were examined with XRD. Prepared thin films showed improvement of dispersion angle of c-axis orientation ${\Delta}{\theta}_{50}$ caused by inserting Buffer-layer and amorphous Si underlayer.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.1
• /
• pp.5-10
• /
• 2002

This study was performed to investigate the influence of spraying condition to the coating layer properties of Fe-Cr-Ni-Mo-Si-B alloy using the HVOF. The investigations, such as thickness measurement, surface roughness, hardness, friction coefficient, resistance of corrosion were carried out. Matrix is prepared by gritting and coating layer is made of Fe-Cr-Ni-Mo-Si-B alloy powder using HVOF. Alumina gritting layers are superior to steel gritting layers. The less spaying distance, the more coating layer properties confirmed. The optimum spraying condition, in this study, was proved as 13inch spraying distance with feed rate 350rpm (78g/min).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.81-82
• /
• 2008

하이브리드 코팅 시스템을 이용하여 $CrMoC_xN_{1-x}$ 박막을 AISI D2와 실리콘 웨이퍼 모재 위에 증착하였다. 박막 내 탄소 함량은 $CH_4/(CH_4+N_2)$ 가스 유량 증가에 비례하여 증가했다. 탄소 함량이 0.33일 때 44GPa의 최대강도 및 -4.4GPa의 잔류응력을 나타내었다. CrMoN 박막의 평균 마찰계수는 0.42이지만, 탄소함량을 증가함에 따라 0.31까지 감소 하였다. 이것은 박막 표면과 스틸볼 사이에서 탄소가 풍부한 층이 형성되어 일종의 고체윤활제 역할을 했기때문이다. 박막의 미세조직은 X-ray diffraction, Scanning electron microscopy, 그리고 X-ray photoelectron spectroscopy를 이용하여 분석하였다.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.1
• /
• pp.49-55
• /
• 2001

The addition of organic compound containing -COOH, X$800_2$, -CHO group such as formic acid, formamide, formaldehyde or diethyleneamine to a chromium electroplating bath results in a chromium deposit in which carbon is incorporated. Such deposits have fewer defects than chromium layers produced by a conventional method. It was found that the as-deposited layers were amorphous and auger electron spectroscopy (AES) showed that carbon is distributed uniformly in the deposit. During heat treatment, Cr-C deposits began to crystallize at $400^{\circ}C$, and at $800^{\circ}C$ they were crystallized into chromium carbides and oxides. The effects of current density, amount of additives, applied current waveform on Cr-C alloy electroplating were examined.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.40-44
• /
• 2014

The purpose of this paper is to investigate polarization characteristics of WC-based alloy coatings in alkaline solution. The coatings were fabricated with WC-CrC-Ni, WC-Co-Cr and WC-Co composite powders by HVOF process. Corrosion tests of coatings and substrate were carried out using potentiostat/galvanostat at solution with pH 8 and pH 13. Corrosion potential(Ecorr) and corrosion current density(Icorr) could be studied from polarization curve, and corrosion behavior was analyzed by SEM and EDS. WC-Co-Cr coating and WC-CrC-Ni coating showed more favorable anti-corrosion characteristics than WC-Co coating and substrate at solution with pH 8 and pH 13.

• Journal of Power System Engineering
• /
• v.18 no.4
• /
• pp.72-77
• /
• 2014

The aim of this study to investigate polarization characteristics of WC-based alloy coatings fabricated by high velocity oxygen fuel(HVOF) process. The coatings were fabricated by HVOF process with WC-CrC-Ni, WC-Co-Cr, WC-Co composite powders. Corrosion tests were carried out using potentiostat/galvanostat at solution with pH 2 and pH 6. Corrosion potential(Ecorr) and corrosion current density(Icorr) could be analyzed from polarization curve. WC-Co-Cr coating showed more incorrodible characteristics than other coatings at solution pH 2. WC-CrC-Ni coating was more favorable anti-corrosion characteristics than other coatings at solution with pH 6.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.3
• /
• pp.163-175
• /
• 1996

Flame-sprayed Ni-based coatings are investigated in order to improve the thermal fatigue properties of gray cast iron in the presence of water spraying. The results of thermal cycling tests from room temperature to $1100^{\circ}C$ indicate that thermal fatigue endurance is increased in the order of Ni-20%Cr, NiCr-6%Al, and Ni-5%Al. The thermal fatigue failure is caused by the formation of iron oxides between the coating and the substrate and then the thermal fatigue cracks have propagated either along the brittle iron oxide layer resulting in the spatting of the coatings in case of Ni-5%Al and NiCr-6%Al coatings or to the substrate resulting in the whole specimen fracture in case of Ni-20%Cr coating. It seems that the most governing factor for thermal fatigue resistance is the thermal expansion coefficient difference between the coating and the substrate. Microstructural variations before and after the tests are also discussed.

• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.290-296
• /
• 2009

We report on the effects of mixing of powders with various particle sizes on fracture toughness and wear resistance of thermally sprayed WC-10Co-4Cr coating layers fabricated by HVOF (high-velocity oxygen fuel) process. The size and the mixing ratio of powders were changed in order to get high fracture toughness and wear resistance. The mixing of small amount of coarse powders with fine powders resulted in the highest fracture toughness and wear resistance due to the lowest porosity in coating layers.