• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.531-536
• /
• 2001

Co-22 %Cr alloy films are promising for high-density perpendicular magnetic recording media with their perpendicular anisotropy and large coercivity of 3000 Oe. We observed that a self organized nano structure (SONS) of fine ferromagnetic Co-enriched phase and paramagnetic Cr-enriched phase appears inside the grain of Co-Cr magnetic alloy thin films at the elevated substrate temperature after do-sputtering. The periodic fine Co-enriched phase and Cr-enriched phase is the plate shape of 80 (equation omitted)-wide and 1000 (equation omitted)-long. Cr-enriched phases are located at the center of grains. We prepared 5000 (equation omitted) -thick Co-22 %Cr films on polyimide substrate with varying substrate temperature of $ 30^{\circ}C$, $ 150^{\circ}C$ ,200 $^{\circ}C$, $300^{\circ}C$, and $400^{\circ}C$, respectively. A transmission electron microscope equipped with energy dispersive X-ray analyzer is employed to observe the microstructure of each samples after Co-enri-ched phase are etched selectively. The self organized nano structure of Co-enriched and Cr-enriched lamellar is observed above the substrate temperture of $150^{\circ}C$. No compositional change is observed with substrate temperature. The compositional phase separation in self organized structure becomes clear as the substrate temperature increases. Our results implies that the self organized nano structure in Co-22 %Cr film is ideal for ultra high density recording media by recording selectively on Co-enri-ohed phase.

• Journal of Environmental Science International
• /
• v.8 no.3
• /
• pp.387-391
• /
• 1999

$Pb^{2+}$ and $Cr^{3+}$ uptake capacity by Sargassum horneri was 185.5 mg $Pb^{2+}$/g biomass and 102.6 mg $Cr^{3+}$/g biomass, respectively. An adsorption equilibria were reached within about 0.5 hr for $Pb^{2+}$ and 1 hr for $Cr^{3+}$. The adsorption parameters for $Pb^{2+}$ and $Cr^{3+}$ were determined according to Langmuir and Freundlich model. With an increase in pH values of 2 to 5, $Pb^{2+}$ uptake was increased, however $Cr^{3+}$ uptake jwas constant. The selectivity of mixture solution showed the uptake order of $Pb^{2+}$>$Cu^{2+}$>$Cr^{3+}$>$Cd^{2+}$. $Pb^{2+}$ and $Cr^{3+}$ adsorbed by S. horneri could be recovered from 0.1M HCl, 0.1M ${HNO}_3$ and 0.1M EDTA by desorption process, and the efficiency of $Pb^{2+}$ desorption was above 98%, whereas the efficiency of $Cr^{3+}$ desorption was below 34%.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.2
• /
• pp.125-134
• /
• 2001

($Ti_{1-x}$ $Cr_{x}$ )N coatings were deposited by an ion-plating method in a reactor with two separate metal sources, Ti and Cr. Ti was evaporated using an electron beam, while Cr evaporation was carried out by resistant heating. The Ti and Cr concentrations in the coatings were controlled by the Ti and Cr evaporation ratio. The coating hardness increased with increasing the Cr content(x) and showed a maximum value of 6,000 HK at around x=0.8. The critical load of the coatings, measured by the scratch test, was around 30 N. The wear resistance properties of the ($Ti_{1-x}$$Cr_{ x}$)N coatings were evaluated using a CSEM pin-on-disk type tribometer. A Cr-steel ball as well as a SiC ball, which had hardness values of 590 HK and 2,600 HK respectively, were used as the pin. After the wear test, the surface morphology, roughness and the concentration of the coatings were investigated, with the main focus being on the effect of wear debris and the transferred layer on the wear behavior.

• Journal of Technologic Dentistry
• /
• v.34 no.4
• /
• pp.353-359
• /
• 2012

Purpose: The aim of this study measured and compared the marginal and internal fit of metal cores with two base metal alloy (Ni-Cr alloy(non-beryllium), Co-Cr alloy). Methods: Maxillary right first molar abutment fabricated by titanium was prepared for this study. Impressions(10ea) were made from titanium model, and study models were poured with improved dental stone. Wax cores of twenty were prepared for burn-out and casting. Ten wax cores cast Ni-Cr alloy(non-Be), and finally ten cast Co-Cr alloy. Marginal and internal fit of cores was evaluated using silicone replica technique and digital microscope(x160). The data were statistically analyzed with the independent samples t-test (${\alpha}$ <.05). Results: Mean(standard deviation, SD) marginal and internal fit total size of Ni-Cr alloy(non-Be) group was $73.3(14.4){\mu}m$ and of Co-Cr alloy group $65.6(17.4){\mu}m$. The marginal and internal fit total size of Ni-Cr alloy group(non-Be) was statistically significantly greater than that of Co-Cr alloy group (P=.004). Conclusion: Co-Cr alloy cores in this study had a better marginal fit than Ni-Cr alloy(non-Be) cores.

• The Journal of Korean Academy of Prosthodontics
• /
• v.18 no.1
• /
• pp.49-57
• /
• 1980

The adhesive mechanisms on the metal-ceramic restorations have been reported to be mechanical interlocking, chemical bonding, compressive force, and Van der Waal's force, etc. Of these, the mechanical interlocking and chemical bonding forces are thought to affect the adhesive force between Ni-Cr alloy and porcelain. This study investigates the adhesion of Ni-Cr alloy to porcelain according to surface treatment. For this purpose, the following experiments were made; The compositions of Ni-Cr alloy as cast by emission spectrograph, and the oxides produced on Ni-Cr alloy during degassing at $1850^{\circ}F$ for 30 minutes in air and in vacuum were analyzed by X-ray diffractograph. The metal phases of Ni-Cr alloy were observed according to porcelain-baking cyclic heat treatment by photo microscope and the distribution and the shift of elements of Ni-Cr alloy and porcelain and the failure phases between Ni-Cr alloy and porcelain by scanning electron microscope. The adhesive force between Ni-Cr alloy and porcelain was measured according to surface treatment with oxidization and roughening by Instron Universal Testing Machine. Results were as follows; 1. The metal phases of Ni-Cr alloy as cast and degassing state showed the enlarged and fused core, but when subjected to porcelain-baking cyclic heat treatment, showed a dendrite growing. 2. The kinds of metal oxides produced on Ni-Cr alloy during degassing were found to be NiO and $Cr_2O_3$. 3. The distribution of elements at the interface of Ni-Cr alloy and porcelain in degassing state showed demarcation line, but in roughening state, showed mechanical interlocking phase. 4. The shift of elements at the interface occurred in both states, but the shift amount was found to be larger in roughening than in degassing. 5. The adhesive force between Ni-Cr alloy and porcelain was found to be $3.45{\pm}0.93kg/mm^2$, in degassing and $3.82{\pm}0.99kg/mm^2$, in roughening. 6. The failure phase between Ni-Cr alloy and porcelain showed the mixed type failure.

• BMB Reports
• /
• v.44 no.4
• /
• pp.262-266
• /
• 2011

The aac(6')-Ib gene is the most prevalent gene that encodes aminoglycoside-modifying enzymes and confers resistance to tobramycin, kanamycin, and amikacin. The aac(6')-Ib-cr variant gene can induce resistance against aminoglycoside and fluoroquinolone simultaneously. Two main methods, sequence analysis and the restriction enzyme method, can detect the aac(6')-Ib-cr variant in clinical strains. We collected the 85 strains that were believed to be aac(6')-Ib positive from clinical isolates. Among them, 38 strains were the wild-type; the remaining 47 strains were the aac(6')-Ib-cr variant. Of these 47 strains, 19 simultaneously harbored aac(6')-Ib and aac(6')-Ib-cr. Our study aims to report the characteristics of the 19 strains that simultaneously harbored both genes. This study is the first investigation published in Korea of strains that included both aac(6')-Ib and aac(6')-Ib-cr variant.

• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.477-482
• /
• 2015

This study examined the adsorption characteristics of heavy metal ions ($Cr^{6+}$, $As^{3+}$) in an aqueous solution using recycled aggregate (RA) and recycled aggregate (RA)/steel slag (SS) composites. The RA and SS are favorable for the absorbent because it contains about 91% and 86.9%, respectively, which are some of the major adsorbent ingredients (CaO, $SiO_2$, $Al_2O_3$ and $Fe_2O_3$) for heavy metal. Kinetic equilibrium of $Cr^{6+}$ and $As^{3+}$ in RA and RA/SS composites reached within 180 min and 360 min, respectively. The kinetic data presented that the slow course of adsorption follows the Pseudo first and second order models. The equilibrium data were well fitted by the Freundlich model and showed the affinity order of $As^{3+}$ > $Cr^{6+}$. The results of $As^{3+}$ also showed that the adsorption capacity slightly increased with increasing pH from 6 to 10. Meanwhile, the adsorption capacity of $Cr^{6+}$ was slightly decreased. From these results, it was concluded that the RA and RA/SS composites can be successfully used for removing the heavy metals ($Cr^{6+}$ and $As^{3+}$) from aqueous solutions.

• Journal of the Korean Magnetics Society
• /
• v.20 no.6
• /
• pp.207-211
• /
• 2010

We have investigated the magnetoresistance effect in $Cr_5S_6$ single crystals prepared by vapor transport method. Room temperature X-ray diffraction (XRD) study reveals the phase formation of the single crystals with trigonal crystal structure. The magnetization was measured as a function of temperature (5 K~400 K) and applied magnetic field (0.1 T and 5 T). The magnetization curve as a function of temperature reveals the two transition states of $Cr_5S_6$: one from antiferromagnetic to ferrimagnetic state at ~150 K and the other from ferrimagnetic to paramagnetic state at ~300 K. Temperature dependent resistivity at 0 T and 5 T magnetic field shows the metallic behavior, showing the transition from antiferromagnetic to ferrimagnetic state at ~150 K. Magnetic field dependence of magnetization was measured at four fixed temperatures viz. 100 K, 150 K, 200 K, and 300 K. It is observed that at 200 K and 300 K it shows well M-H hysteresis behavior, whereas at 100 K and 150 K it shows non-hysteretic nature. A negative magnetoresistance (MR) of -2% is observed at 5 T for $Cr_5S_6$ single crystal at 150 K, near the antiferromagnetic transition temperature.

• Korean Journal of Environmental Biology
• /
• v.22 no.1
• /
• pp.120-126
• /
• 2004

Kenaf plants were hydroponically grown in reactor containing toxic metals as Cd, Cu, Cr, Ni and Zn to examine the ability to take up heavy metal. The plants were fertilized using a nutrient solution, which was appropriately adjusted to optimum pH, DO and conductivity. For n hydraulic retention time of 8 days, Cr, Cd, Cu, Ni and Zn were removed up to 90.5, 80.5, 66.1%, 71.1% and 79.4%, and reduced from 2.34 to 0.54 mg $L^{-1}$, 3.37 to 1.07 mg $L^{-1}$, 4.92 to 3.19 mg $L^{-1}$, 6.31 to 4.41 mg $L^{-1}$ and 6.27 to 2.09 mg $L^{-1}$. Especially, accumulation rate of Cr, Cd, Cu, Ni and Zn in the plant were measured up to 347.32, 275.39, 157.52, 50.48 and 211.01 mg DW kg $L^{-1}d^{-1}$, respectively. We considered that Kenaf plants removed Cr, Cd and Zn more effectively than other toxic metals applied.

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.672-675
• /
• 2000

E.coli ATCC 33456 has relatively higher activity of Cr(VI) reduction than other microorganism. The purpose of this research is cloning of Cr(V) reductase from E.coli ATCC 33456. Using colony and southern hybridization, we selected two condidates. Among candidates, pNCR9 is higher Cr(VI) reduction activity than E.coli ATCC 33456. Purified Cr(VI) reductase antibody was reacted at estimated 42Kda protein band of candidate's crude extract on 12% SDS-PAGE. This results showed cloned gene's product is very similar to purified Cr(VI) reductase from E.coli ATCC 33456.