• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.51-62
• /
• 1999

The objective of this research is to develop paper sludge reinforced thermoplastic composites which incorporate the advantages of each component materials. The effects of paper sludge content(0, 10, 20, 30, 40----), mesh size(20~40, 60~80, less than 100mesh), and coupling agent(Epolene E-43 and Epolene G-3003) on the mechanical properties of paper sludge-polypropylene composites were investigated. Composite density increased with an increase in the paper sludge content. When paper sludge is incorporated into a polypropylene matrix, the flexural properties of the composite increase significantly with an increase in the paper sludge mixing ratio. Especially, flexural modulus was improved with increasing paper sludge content. The flexural strength of composites was improved, but flexural modulus reduced somewhat with decreasing paper sludge particle size. The flexural properties of paper sludge-polypropylene composites were improved by using coupling agents to enhance the bonding between reinforcing filler and matrix. Use of the epolene E-43 and G-3003 resulted in considerable improvement in the flexural strength over control specimens. The flexural strength of the G-3003 composite system is higher than that of the E-43 system. Generally, izod notched impact strength of paper sludge-polypropylene composite decreased slightly, whereas izod unnotched impact strength decreased significantly with increasing paper sludge contents. There was no effects of paper sludge particle size on impact strength of paper sludge-polypropylene composites. And izod unnotched impact strength of epolene E-43 composite system sharply decreased but that of G-3003 composite system was no tendency with increasing additive content.

• Membrane Journal
• /
• v.17 no.1
• /
• pp.44-53
• /
• 2007

The primary objective of this study is to increase the extent of water flux and fouling resistance of nano-filtration or reverse osmosis membranes. This study was performed to investigate the effect of surface characteristics of silane coated membranes on modified fouling index. Commercial polyamide composite RO membrane (RE1812-LP) and NF membrane (ESNA4040-LF) were treated with silane coupling agents in ethanol at five different concentrations. The silane coupling reagent, aminopropylmethoxydiethoxysilane, contains one aminoalkyl and three alkoxy groups. The hydrophilic effect of aminoalkyl group of APMDES on the permeability and fouling resistance of the modified membrane was examined. The surfaces of the modified membranes were characterized by FE-SEM, contact angle analyzer, and zeta potentiometer in order to confirm successful sol-gel methods. The modified NF membranes showed significantly enhanced water flux and fouling resistance without a decrease in salt rejection in divalent ionic feed solution.

• Polymer(Korea)
• /
• v.26 no.4
• /
• pp.445-451
• /
• 2002

In this work, the adsorption characteristics and mechanical interfacial properties of treated silicas by silane coupling agents, such as, ${\gamma}$-methacryloxy propyl trimethoxy silane (MPS), ${\gamma}$-glycidoxy propyl trimethoxy silane (GPS), and ${\gamma}$-mercapto propyl trimethoxy silane (MCPS), were investigated. The equilibrium spreading pressure ($pi_e$), surface free energy ($gamma_s$ s/), and specific surface area ($S_{BET}$) were studied by the BET method with $N_2$/77 K adsorption. The developments of nonpolar functional groups of the silica surfaces treated by silane coupling agents led to the increase in the $S_{BET}$, $pi_e$, and $gamma_s$, resulting in the improved tearing energy ($G_{mc}$)of the silica/rubber composites. The composites treated by MPS showed the superior mechanical interfacial properties in these systems. These results explained by changing of crystalline size, dispersion, agglomerate, and surface functional group of silica/rubber composites.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.232-243
• /
• 2009

The specialized and diversified synthetic and compounding technologies are used to meet the requirements for the advanced high performance tire tread materials with better balance of fuel economy(rolling resistance), safety(wet traction) and wear resistance. These techniques involve the methodology for the improvement of chemical and physical interaction between filler and the rubber matrix using coupling agents as well as a variety of chemically-modified solution SBRs. The research trends about the high performance functional SBRs and coupling agents which can interact with the surface of fillers and their working mechanism were investigated in the conventional carbon black-filled rubber and silica-filled SBR systems developed recently as "green tire".

• Journal of Adhesion and Interface
• /
• v.3 no.4
• /
• pp.44-52
• /
• 2002

Composite materials are created by combining two or more component to achieve desired properties which could not be obtained with the separate components. The use of reinforcing fillers, which can reduce material costs and improve certain properties, is increasing in thermoplastic polymer composites. Currently, various inorganic fillers such as talc, mica, clay, glass fiber and calcium carbonate are being incorporated into thermoplastic composites. Nevertheless, lignocellulose fibers have drawn attention due to their abundant availability, low cost and renewable nature. In recent, interest has grown in composites made from lignocellulose fiber in thermoplastic polymer matrices, particularly for low cost/high volume applications. In addition to high specific properties, lignocellulose fibers offer a number of benefits for lignocellulose fiber/thermoplastic polymer composites. These include low hardness, which minimize abrasion of the equipment during processing, relatively low density, biodegradability, and low cost on a unit-volume basis. In spite of the advantage mentioned above, the use of lignocellulose fibers in thermoplastic polymer composites has been plagued by difficulties in obtaining good dispersion and strong interfacial adhesion because lignocellulose fiber is hydrophilic and thermoplastic polymer is hydrophobic. The application of lignocellulose fibers as reinforcements in composite materials requires, just as for glass-fiber reinforced composites, a strong adhesion between the fiber and the matrix regardless of whether a traditional polymer matrix, a biodegradable polymer matrix or cement is used. Further this article gives a survey about physical and chemical treatment methods which improve the fiber matrix adhesion, their results and effects on the physical properties of composites. Coupling agents in lignocellulose fiber and polymer composites play a very important role in improving the compatibility and adhesion between polar lignocellulose fiber and non-polar polymeric matrices. In this article, we also review various kinds of coupling agent and interfacial mechanism or phenomena between lignocellulose fiber and thermoplastic polymer.

• Korean Chemical Engineering Research
• /
• v.54 no.2
• /
• pp.163-170
• /
• 2016

In order to improve the hydrophilic property of polymer films, coating solutions which showed a good hydrophilic property, were prepared by the sol-gel method. The coating solutions were prepared by adding different types of silane coupling agents (aminosilane, epoxysilane and acrylsilane) to a colloidal silica (15 nm diameter). The solutions prepared by adding aminosilane resulted in gels which could not be used as coating solutions. On the other hand, the coating solutions prepared by the addition of epoxysilane showed contact angles of $10{\sim}15^{\circ}$ and good hydrophilic property at R=0.10~0.15 (R=silane coupling agent/colloidal silica weight ratio). In addition, the coating solutions prepared by the addition of acrylsilane at R=0.03~0.07, exhibited contact angles of $5{\sim}10^{\circ}$, which means better hydrophilic property than aminosilane or epoxysilane.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.2
• /
• pp.531-540
• /
• 2019

Hydrophilic and hydrophobic nanosilica and tetraethyl orthosilicate (TEOS) as a coupling agent was used to form a coarse spike structure as well as an excellent reactive hydroxyl groups on the glass surface. Then, a second treatment was carried out using a trichloro-(1H,1H,2H,2H)perfluorooctylsilane(TPFOS) solution for ultimate water repellent glass surface formation. The formation of hydrophobic coating layer on glass surface using silica aerosol, which is hydrophobic nanosilica, was not able to form a durable hydrophobic coating layer due to the absence of reactive -OH groups on the surface of nanosilica. On the other hand, a glass surface was first coated with a coating liquid prepared with hydrophilic hydroxyl group-containing nanosilica and hydrolyzed TEOS, and then coated with a TPFOS solution to introduce a hydrophobic surface on glass having a water contact angle of $150^{\circ}$ or more. The sliding angle of the coated glass was less than $1^{\circ}$, which meant the surface had a super water-repellent property. In addition, as the content of hydrophilic nanosilica increased, the optical transmittance decreased and the optical transmittance also decreased after 2nd coating with the TPFOS solution. The super-hydrophobic property of the coated glass was remained up to 50 times of rubbing durability test, but only hydrophobic property was shown after 200 times of rubbing durability test. Conclusively, the optimal coating conditions was double 1st coatings with the HP3 coating solution having a hydrophilic nanosilica content of 0.3 g, and subsequent 2nd coating with the TPFOS solution. It is believed that the coating solution thus prepared can be used as a surface treatment agent for solar cells where light transmittance is also important.

• Journal of Environmental Science International
• /
• v.15 no.6
• /
• pp.593-600
• /
• 2006

SIS triblock copolymers, one of the major raw materials of oil gelling agent, were synthesized by living anionic polymerization and the resultant copolymers formed with various shapes and sizes were used to examine their oil gelling capacities. Coupling method was adapted to form final triblock products from diblock living polymers. Prior to polymerization, the impurities in monomers and solvents were throughly removed by killing technique. We experimentally investigated the effects of operating parameters of synthesis and forming of SIS triblock copolymers on oil gelling capacity. The photocatalytic decomposition of SIS triblock copolymer under ultraviolet circumstance was also investigated and it is found that the addition of P-25 enhances the photocatalytic decomposition.

• Progress in Superconductivity and Cryogenics
• /
• v.22 no.2
• /
• pp.12-16
• /
• 2020

Circulating cooling systems consume a lot of water, and most of the water from river, which contains a large amount of Ca2+, Mg2+, et al, and has the characteristics of high hardness and large turbidity. The water can form scale on the surface of the heat exchanger and the pipes, which would reduce the heat transfer efficiency and affect the heat exchanger's length of service. In this study, the Superconducting High Gradient Magnetic Separation (S-HGMS) technology was used in river water treatment and the effects of agent A, agent B, and S-HGMS on the removal of hardness and turbidity were discussed. The results showed that the hardness removal rate reached 71.3% and the turbidity was decreased to 0.5 NTU.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.24 no.3
• /
• pp.38-44
• /
• 1998

The skin permeation and the skin primary irritation of two UV filters from caprylic capryl triglyceride (oil), oil in water (O/W) and water in oil (W/O) emulsions, were evaluated. We selected octyl moth-oxycinnamate (OMC) broadly used in cosmetics and polymeric sunscreen agent (PSA, average MW: 2,000) synthesized by the coupling reaction of 2-ethylhexyl 4-hydroxycinnamate with poly vinylbenzyl chloride, as model UV filters. For in vitro skin permeation experiments, Franz diffusion cells (effective diffusion area:1.766cm) and the excised skin of female hairless mouse aged 8 weeks were used. Oil or emulsion containing UV filters was applied in the donor compartment. The skin primary irritation was evaluated with fe-male guinea pigs (8-10 weeks,350-400 g). In oil and emulsions, the skin permeability and the skin primary irritation of PSA were lower than those of OMC. The skin permeability of UV filters was lower when they were in oil-in-water emulsion (OIW) than water-in-oil emulsion (W/O). We suggest that O/W system would be more useful when compared with W/O system, and PSA could be a good candidate for a future sunscreen agent for reducing the skin irritation.