• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.148-150
• /
• 2002

In this paper, a 5-coupled BPF with teflon substrate is presented. In general, for less than 1 GHz frequency, the narrow bandwidth as well as the good characteristic in the rejection frequency band could be realized using lumped elements. However, for higher than 1 GHz frequency, the distributed elements such as microstrip lines need to be used for the design of the desired BPF For less than 2 GHz, the FR4 shows good filter characteristic at low cost. However, in the range of 2 GHz ~ 10 GHz, the filters with FR4 show a big difference between simulation and measurement results. Thus, in such a high frequency region, the teflon is more preferred to the FR4. The center frequency (fc) of the proposed filter is 2.3 GHz, the insertin loss (IL) is 1.2 dB, the return loss (RL) is 30 dB, bandwidth (BW) is 100 MHz, and the size is 8.3 cm $\times$ 4.9 cm.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.183-185
• /
• 2010

A 2.4 GHz dual-polarized antenna for a Doppler radar is studied. The proposed dual-polarized antenna using a stacked annular ring patch with two co-centric gap-coupled feed lines and a $90^{\circ}$ hybrid exhibits fairly good performance of 22 dB isolation at a center frequency of 2.4 GHz. Using a $90^{\circ}$ hybrid, a right-handed circular polarization for the transmitter and a left-handed circular polarization for the receiver are implemented. The gain of the designed antenna is about 0 dBi over operating frequencies. The antenna size including a ground plane is only $40{\times}40\;mm^2$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.5
• /
• pp.1304-1316
• /
• 1996

In this paper, A VCO(Voltage Controlled Oscillator) in use of clock recovery/data regeneration circuit for 10 Gbps fiber optic receivers was developed. The improved hair-pin resonator with a parallel coupled lines, which has been applied to microstrip filters, was used as a resonance part. As a frequcncy tuning device by substituting 3-terminalMESFET vaaractor for varactor diode, an MMIC manufacturing process will be simplified. Since a hair-pin resonator is planar type compared to the dielectric resonator and has a relatively flat reactance verus frequency, it will be favorable to apply a hair-pin resonator to an MMIC, in addition wideband frequency tuning range is able to be obtained.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.328-332
• /
• 2000

본 논문에서는 기생 패치 구조와 적층 구조의 광대역 마이크로스트립 안테나에 평행 결합 선로 형태의 광대역 임피던스 정합 회로를 결합하여 쉽게 추가적인 임피던스 대역폭 개선을 얻을 수 있음을 제안하였다. 평행 결합 선로 형태의 광대역 임피던스 정합 회로 설계를 위하여 분포 회로 방식의 반복적인 방법을 제시하였고. 설계\ulcorner제작 결과 기생 패치 구조와 적층 구조에서 각각 56.23%와 16.45%의 추가적인 임피던스 대역폭 개선을 이룰 수 있었다. 그리고 방사 패턴과 측정된 이득을 보면 평행 결합 선로의 결합으로 인한 방사 패턴에서의 큰 변화는 보이지 않았고, 이득에서는 평행 결합 선로 부분의 커플링 손실로 인해 최대 이득이 약 1 dB 정도 감소하는 것을 확인할 수 있었다.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.673-675
• /
• 2007

We present the design and fabrication of a 60 GHz medium power amplifier monolithic microwave integrated circuit with excellent gain-flatness for a 60 GHz radio-over-fiber system. The circuit has a 4-stage structure using microstrip coupled lines instead of metal-insulator-metal capacitors for unconditional stability of the amplifier and yield enhancement. The gains of each stage of the amplifier are modified to provide broadband characteristics of input/output matching for the first and fourth stages and to achieve higher gains for the second and third stages to improve the gain-flatness of the amplifier for wideband.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.12
• /
• pp.1402-1407
• /
• 2007

This paper presents a new design method of the Ultra-Wide-Band BandPass Filter using the CRLH-TL(Composite Right- and Left-Handed Transmission-line) having the Metamaterials' properties. Instead of the periodic type or many cells of the CRLH-TL, only the unit cell is used to miniaturize the target component, which can not be realized by the conventional quarter guided-wavelength resonator-based filters. Particularly, the strong coupling essential to the Ultra Wide Band is enabled by the interdigital coupled lines between the grounded stubs. The proposed design scheme is validated by the electromagnetic simulation and measurement of the fabricated filter which shows the total size of 'the guided-wavelength/9.4', the 100 % fractional bandwidth for the UWB, the insertion loss of less than 1 dB and the flat group-delay.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.862-877
• /
• 2008

In this paper, two types of wideband 3-dB ring hybrids are compared and discussed to show the ring hybrid with a set of coupled-line sections better. However, the better one still has a realization problem that perfect matching can be achieved only with -3 dB coupling power. To solve the problem, a set of coupled-line sections with two shorts is synthesized using one- and two-port equivalent circuits and design equations are derived to have perfect matching, regardless of the coupling power. Based on the design equations, a modified ${\Pi}-type$ of transmission-line equivalent circuit is newly suggested. It consists of coupled-line sections with two shorts and two open stubs and can be used to reduce a transmission-line section, especially when its electrical length is greater than ${\pi}$. Therefore, the $3\;{\lambda}/4$ transmission-line section of a conventional ring hybrid can be reduced to less than ${\pi}/2$. To verify the modified ${\Pi}-type$ of transmission- line equivalent circuit, two kinds of simulations are carried out; one is fixing the electrical length of the coupled-line sections and the other fixing its coupling coefficient. The simulation results show that the bandwidths of resulting small transmission lines are strongly dependent on the coupling power. Using modified and conventional ${\Pi}-types$ of transmission-line equivalent circuits, a small ring hybrid is built and named a compact wideband coupled-line ring hybrid, due to the fact that a set of coupled-line sections is included. One of compact ring hybrids is compared with a conventional ring hybrid and the compared results demonstrate that the bandwidth of a proposed compact ring hybrid is much wider, in spite of being more than three times smaller in size. To test the compact ring hybrids, a microstrip compact ring hybrid, whose total transmission-line length is $220^{\circ}$, is fabricated and measured. The measured power divisions($S_{21}$, $S_{41}$, $S_{23}$ and $S_{43}$) are -2.78 dB, -3.34 dB, -2.8 dB and -3.2 dB, respectively at a design center frequency of 2 GHz, matching and isolation less than -20 dB in more than 20 % fractional bandwidth.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.301-306
• /
• 2014

We proposed a new PCB-type 'common-mode current($I_c$) and differential-mode current($I_d$) detector' working for fast detection of $I_c$ and $I_d$ from the differential-mode signaling, with miniaturization effect and possibility of cheaper fabrication. In order to realize this device, we suggest a branch-line-coupler balun having a composite right- and left-handed(CRLH) one-layer microstrip phase-shifting line as compact as roughly ${\lambda}_g/14$. The presented balun obviously is different from the conventional bent-&-folded delay lines or slits on the ground for coupling the lines on the top and bottom dielectrics. As we connect the suggested balun output ports of the differential-mode signal lines via the through-port named U and coupled-port named L, $I_c$ and $I_d$ will appear at port ${\Delta}$ and port ${\Sigma}$ of the present device, in order. The validity of the design scheme is verified by the circuit-and numerical electromagnetic analyses, and the dispersion curve proving the metamaterial characteristics of the geometry. Besides, the examples of the $I_c$ and $I_d$ indicator are observed as the even and odd modes in differential-mode signal feeding. Also, the proposed device is shown to be very compact, compared with the conventional structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.513-520
• /
• 2001

In this paper, the directional coupler using three layer microstrip substrate is proposed and the design method is notified. Modified re-entrant mode coupler is the proposed structure that one layer is added on upper plane of coupled transmission lines and the floating conductor is placed on added layer's upper planes. This structure has high coupling for the increase of odd mode capacitance and also has good performance in VSWR, isolation, phase difference because the difference of effective permittivity is small in each mode. We have designed the coupler from the calculation of impedance, effective permittivity, coupling coefficient using even, odd mode analysis method. From the simulation and measurement, proposed coupler has about 2 dB more tighter coupling than conventional coupler and also has good performance in VSWR, isolation, phase difference.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.2 no.4
• /
• pp.199-202
• /
• 2007

In this paper, we examined the operating principle of a passive tag antenna for RFID system in UHF band. Based on the study, we proposed a novel RFID tag antenna which adopts the inductively coupled feeding structure to match antenna impedance to a capacitively loaded commercial tag chip. The proposed tag antenna consists of microstrip lines on a thin PET substrate for low-cost fabrication. The detail structure of the tag antenna were optimized using a full electromagnetic wave simulator of IE3D in conjunction with a Pareto genetic algorithm, and the size of the tag antenna can be reduced up to kr=0.27(2 cm2). We built some sample antennas and measured the antenna characteristics such as a return loss, an efficiency, and radiation patterns. The readable range of the tag antenna with a commercial RFID system showed about 1 to 3 m.