• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.477-479
• /
• 2006

In this study, a stripe type counter electrode discharge cell for PDP was attempted to realize high luminance efficiency and low firing voltage for fine pitch discharge cells. The cells were prepared using electroplated Cu/Ni electrodes coated with glass dielectric layer. The discharge behaviors of such cells were observed. These results indicate that the counter electrode discharge cells have different discharge behavior compared with coplanar cells, which may affect the luminance efficiency of the panel.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.419-421
• /
• 2008

Sputter deposition on a Pt counter electrode was studied using RF plasma as the improvement of conversion efficiency for dye-sensitized solar cells (DSC). The effects of the sputtering thickness and incident angle on a Pt counter electrode for DSC was scrutinized. We conducted the experiment to get the optimal sputtering time for the performance of the DSC. Under the sputtering time condition of 120 seconds, we varied the incident angles of substrate from $0^{\circ}$ to $60^{\circ}$. Under standard test condition (AM 1.5, 100mW/$cm^2$), we obtained the maximum efficiency of 4.61% at the incident angle of $40^{\circ}$ with an active cell area of $1cm^2$.

• Analytical Science and Technology
• /
• v.27 no.6
• /
• pp.308-313
• /
• 2014

The effect of electrochemical characteristics of dye-sensitized solar cells (DSSC) upon employing multi-wall carbon nanotube (MWCNT) on both working electrode and counter electrode were examined with using EIS, J-V curves and UV-Vis absorption spectrometry. When 0.1 wt% of MWCNT was employed in the $TiO_2$-MWCNT composit on working electrode, the energy conversion efficiency increased about 12.5% compared to the $TiO_2$ only working electrode. The higher light conversion efficiency may attribut to the high electrical conductivity of MWCNT in $TiO_2$-MWCNT composite which improves the electron transport in the working electrode. However, higher amount of MWCNT than 0.1 wt% in the $TiO_2$-MWCNT composite decreases the light conversion efficiency, which is mainly ascribed to the decreased transmittance of light by MWCNT and to the decreased adsorption of dye onto $TiO_2$. The MWCNT employed counter electrode exhibited much lower light conversion efficiency of DSSC than the Pt-counter electrode, while the MWCNT-Pt counter electrode showed similar in light conversion efficiency to that of Pt-counter electrode.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.333-339
• /
• 2011

In this work, electrochemical characteristics and optical transmittance of carbon nanotubes (CNTs) counter electrodes which had different amount of CNTs in CNTs slurries were analyzed. Two-step heat treatment processes were applied to achieve well-fabricated CNTs electrode. Three sets of CNTs electrodes and dye-sensitized solar cells (DSSCs) with CNTs counter electrodes were prepared. As the amount of CNTs increased, sheet resistance of CNTs electrode decreased. CNTs electrode with low sheet resistance had low electrochemical impedance and fast redox reaction. On the other hand, in case of CNTs counter electrode with low density of CNTs, performance of the dye-sensitized solar cell was improved due to its high optical transmittance. We found that the transmittance of CNTs counter electrode influence the performance of dye-sensitized solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.160-160
• /
• 2013

Dye-sensitized solar cells (DSSCs) have attracted much attention because of their moderate light-to-electricity conversion efficiency, easy fabrication, and low cost. At present, platinum (Pt) is used as a counter electrode in DSSCs. However, it is found that Pt dissolves in iodide electrolyte solutions and creates chemical compound such as PtI4 and H2PtI6. Carbon based materials are one of candidates for a counter electrode of DSSCs. We prepare two types of graphite oxides by different chemical treatments; original graphite oxide, hydrazine treated graphite oxide. Each graphite oxide and magnesium nitrate dispersed in deionized water are prepared as solutions for electrophoretic deposition (EPD). Each graphite oxide electrode is deposited on fluorine-doped tin oxide (FTO) substrate by EPD method. Structural and electrochemical properties of each electrode are investigated by field-emission scanning electron microscopy and electrochemical impedance spectroscopy, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.154-157
• /
• 2006

The counter electrode widely used in DSCs (Dye-sensitized Solar Cells) is constructed of conducting glass substrates coated with Pt films, where the platium acts as a catalyst. Pt counter electrodes in DSCs are one important component. It is expected that characteristics of Pt electrodes strongly depend on fabrication process and its surface condition. In this study, Pt counter electrode surface of DSC is deposited by reactive RF magnetron sputtering under the conditions of Ar 5mtorr, RF power of 120w and substrate temperature of $100^{\circ}C$. Surface morphology of Pt electrodes was investigated by FE-SEM and AFM. And this paper shows our recent results and technology to fabricate the new designed cell with Pt electrodes deposited by sputtering method. We have achieved fill factor 65% and photoelectric conversion efficiency around 2.6% as the best results of new designed DSCs structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.234-234
• /
• 2013

The counter electrodes in dye-sensitized solar cells (DSSCs) play roles in not only collecting electrons from external circuit but also reducing I3- to I- in electrolytes. Generally, conventional counter electrodes for DSSCs are prepared from the high temperature treatment of the H2PtCl6 precursor solution at $400^{\circ}C$ However, the more simplified fabrication process of counter electrodes is required for the commercialization of DSSCs. In this work, we developed novel fabrication process of counter electrodes using nano-second pulsed laser. DSSCs employing counter electrodes prepared by laser process showed conversion efficiency of 6.75% with short-circuit current of 12.73 mA/cm2, open-circuit voltage of 0.74 V and fill factor of 0.72. Closer investigating of photovoltaic properties will be reported.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.1
• /
• pp.63-69
• /
• 2017

In this work, two different platinum (Pt) counter electrodes have been prepared by spin coating a Pt solution and screen printing a Pt paste on fluorine doped tin oxide (FTO) glass substrate followed by sintering at $380^{\circ}C$ for 30 min. Linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) analyses of the Pt electrodes showed that the spin coated electrode was catalytically more active than the screen printed electrode. The above result agrees well with the surface morphology of the electrodes studied by atomic force microscopy (AFM) and the photovoltaic performance of the dye-sensitized solar cells (DSSCs) fabricated with the Pt electrodes. Moreover, calculation of current density-voltage (j-V) curves according to diode model with the parameters obtained from the experimental j-V curves and the EIS data of the DSSCs provided a quantitative insight about how the catalytic activity of the counter electrodes affected the photovoltaic performance of the cells. Even though the experimental situations involved in this work are trivial, the method of analyses outlined here gives a strong insight about how the catalytic activity of a counter electrode affects the photovoltaic performance of a DSSC. This work, also, demonstrates how the photovoltaic performance of DSSCs can be improved by tuning the performance of counter electrode materials.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.588-593
• /
• 2010

Sputter deposition on a Pt counter electrode was studied using radio frequency (RF) plasma as the improvement of incident photon to current conversion efficiency (IPCE) for dye-sensitized solar cells (DSCs). Effects of the sputtering thickness and the incident angle on a Pt counter electrode for DSCs were investigated. Experiments to get the optimal sputtering time for the performance of the DSCs were carried out. And it is found that the optimized sputtering time was 120 seconds, in addition, the incident angles of the substrate was adjusted from $0^{\circ}$ to $60^{\circ}$. The maximum efficiency of 5.37% was obtained at the incident angle of $40^{\circ}$ with an active cell area of $1cm^2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.331-334
• /
• 2007

탄소나노튜브는 화학적 안정성과 고전도성을 갖는 동시에 높은 비표면적을 지니고 있다. 이와 같은 특정으로 염료감응형태양전지의 상대전극으로 사용 가능이 기대되어 지고 있으나, 아직 성공적인 연구가 발표되고 있지 않다. 많은 연구자들이 CNT 자체만으로 원하는 효과를 얻지 못하고 있기 때문에, CNT 조작(가공)을 통해 CNT 특성을 올리고자 노력하였다. 그러나 본 연구에서, 가공하지 않은 CNT powder를 이용하여 paste를 제조하고 doctro-blade법으로 코팅하여 CNT counter electrode를 제조하여 DSSC의 상대전극으로써의 적용 가능성을 조사 해 보았다. 제조된 CNT counter electrode에 대한 CNT 자체만의 전기화학적 특성을 측정하였다. 그리고 DSSC 에 직접 적용하여 전지의 광전특성을 측정하였다. 그 결과 탄소나노튜브의 고전도성 특성과 넓은 비표면적 특성에 의해 상대전극의 전해질/전극계변에서의 전해질의 산화환원 반응에 대한 촉매 작용을 향상시키고, 상대전극 표변에서의 전자전달 속도를 높여 염료감응형 태양전지의 효율을 높이는 것으로 확인되어졌다.