• 한국안전학회지
• /
• 제27권1호
• /
• pp.7-13
• /
• 2012

This paper describes the diagnosis techniques using UV images taken in the field under energized condition of power equipments in order to figure out and analyze the abnormal states on the terminals of power equipments. To classify the features of the terminals, the counted No. of the corona generated at the terminals is defined. According to the result detected, the No. of corona detected on the power equipments installed inside a building is less than that installed outside a building, and it strongly depends on the environment and installed condition. Thus, the environmental condition needs enhanced, and stable operation by the periodic inspection under energized condition of the power equipments is required. Especially, the event counting technique using UV camera is useful for the power equipments apart more than 20 m to apply, and there can be an error due to the features of the sensing techniques when the distance between the user and the objects is close less than 15 m. Therefore, the experimental result shows that event counting technique is employed in the case of the distance more than 15 m. The electrical safety can be ensured by using the UV detection technique and the criteria.

• 전기학회논문지
• /
• 제64권9호
• /
• pp.1406-1410
• /
• 2015

The railway catenary systems consist of a complex structure, electrical and mechanical conditions are exposed to dangerous environment due to current collection between pantograph and catenary systems. These two types of conditions for the catenary systems are critically assessed for management and are becoming increasingly more dependent on reliable inspection system. In this paper, a new measurement system which enables inspection of catenary faults was studied and implemented. The system uses wavelength band of ultraviolet (UV) and IR (Infrared) to measure the insulation of corona and temperature of catenary wire. In order to determine the sensitivity of implemented system, the performance test such as distance detection range of UV camera and temperature resolution of IR camera were conducted, respectively. The field test of development system was also conducted in metro and high-speed line using mobile type UV and IR multi-composited measurement systems.

• 전기학회논문지
• /
• 제65권11호
• /
• pp.1937-1942
• /
• 2016

Unlike oil immersed transformers, cast-resin transformers have the solid insulator 'epoxy resin' in sealed structure. Therefore, they reveal a lot of limitations in checking aging conditions and predicting an accident. This study analyzed the characteristics of Cast-resin transformers by the measurement distance and measurement sensitivity with a corona defect sample, using antenna sensor. Therefore, the experiment has proven that the antenna sensor-based measurement method proposed in this study is able to detect the insulation defect location of the cast-resin transformer, unlike conventional measurement methods. It is expected that the result of this study will be used to develop a new type of measuring method in order to measure insulation defects and to use in safety inspection of domestic cast-resin transformers.

• 천문학회보
• /
• 제44권2호
• /
• pp.41.3-41.3
• /
• 2019

To find out the origin and formation mechanism of LASCO-C2 post-CME blobs, we investigate 2 LASCO-C2 blobs and 35 low corona blobs observed by K-Cor on 2017 September 10 from 17:11 to 18:58 UT. By visual inspection of a post-CME ray and the locations of low corona blobs in K-Cor and LASCO-C2 images with examining the time-height data of all blobs, we find the following results: (1) The post-CME ray structure is well identified in the K-Cor images than LASCO-C2 ones. (2) Low corona blobs can be classified into two groups according to their formation mechanisms: 27 blobs belong to Group 1, generated by the tearing mode instability near the middles of current sheets as described by Furth et al., 1963; Shibata & Tanuma, 2001; Shen et al., 2011, the others belong to Group 2, formed by the tearing mode instability near the tips of current sheets as shown in Figure 5 of Sitnov et al., 2002. (3) Group 1 has low initial appearance heights <1.30 Rs>, broad speed range (38 ~ 945 km/s), and high accelerations <4,272 m/s² > than Group 2, which has initial appearance heights <1.72 Rs>, speed range (579 ~ 843 km/s), and accelerations <1,413 m/s² >. (4) among 8 blobs for Group 2, only 2 blobs are temporally and spatially associated with 2 LASCO-C2 ones and their initial observation heights are 1.93 and 1.79 Rs, respectively. Our results firstly demonstrate that LASCO-C2 blobs form the heights from about 1.7 to 2.0 Rs and they are generated by the tearing mode instability near the tips of current sheets.

• 천문학회지
• /
• 제54권2호
• /
• pp.49-60
• /
• 2021

Observations of line of sight (LOS) Doppler velocity and non-thermal line width in the off-limb solar corona are often used for investigating the Alfvén wave signatures in the corona. In this study, we compare LOS Doppler velocities and non-thermal line widths obtained simultaneously from two different instruments, Coronal Multichannel Polarimeter (CoMP) and Hinode/EUV Imaging Spectrometer (EIS), on various off-limb coronal regions: flaring and quiescent active regions, equatorial quiet region, and polar prominence and plume regions observed in 2012-2014. CoMP provides the polarization at the Fe xiii 10747 Å coronal forbidden lines which allows their spectral line intensity, LOS Doppler velocity, and line width to be measured with a low spectral resolution of 1.2 Å in 2-D off limb corona between 1.05 and 1.40 RSun, while Hinode/EIS gives us the EUV spectral information with a high spectral resolution (0.025 Å) in a limited field of view raster scan. In order to compare them, we make pseudo raster scan CoMP maps using information of each EIS scan slit time and position. We compare the CoMP and EIS spectroscopic maps by visual inspection, and examine their pixel to pixel correlations and percentages of pixel numbers satisfying the condition that the differences between CoMP and EIS spectroscopic quantities are within the EIS measurement accuracy: ±3 km s-1 for LOS Doppler velocity and ±9 km s-1 for non-thermal width. The main results are summarized as follows. By comparing CoMP and EIS Doppler velocity distributions, we find that they are consistent with each other overall in the active regions and equatorial quiet region (0.25 ≤ CC ≤ 0.7), while they are partially similar to each other in the overlying loops of prominences and near the bottom of the polar plume (0.02 ≤ CC ≤ 0.18). CoMP Doppler velocities are consistent with the EIS ones within the EIS measurement accuracy in most regions (≥ 87% of pixels) except for the polar region (45% of pixels). We find that CoMP and EIS non-thermal width distributions are similar overall in the active regions (0.06 ≤ CC ≤ 0.61), while they seem to be different in the others (-0.1 ≤ CC ≤ 0.00). CoMP non-thermal widths are similar to EIS ones within the EIS measurement accuracy in a quiescent active region (79% of pixels), while they do not match in the other regions (≤ 61% of pixels); the CoMP observations tend to underestimate the widths by about 20% to 40% compared to the EIS ones. Our results demonstrate that CoMP observations can provide reliable 2-D LOS Doppler velocity distributions on active regions and might provide their non-thermal width distributions.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.1-7
• /
• 2014

For the resistance spot welds of CR1180 and GA1180 TRIP steels, the weld quality evaluation method using the digitalized X-ray transmission imaging apparatus was investigated in comparison with the crosssectional examination method. In the case of the resistance spot welding of CR1180, three circular regions, such as WZ(white zone), GZ(grey zone) and DZ(dark zone), appeared on X-ray image and they corresponded to the diameters of indentation mark, nugget and corona bond, respectively. The variation of X-ray transmission thickness due to the thickness variation of the weld seemed to be mainly responsible for the formation of those contrasts. The X-ray image contrast formed from the variation of transmission thickness at the outer border line of DZ could also enable the inspections of the notch shape, nonuniformity of the welding pressure and spatter from its sharpness, concentricity and the normal straight line, respectively. The X-ray image of the resistance spot weld of galvannealed GA1180 TRIP steel was very similar to that of CR1180 TRIP steel except the crown shaped outer border line of DZ which was considered to be due to the melting behavior of zinc having the boiling temperature even lower than the melting temperature of steel.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 춘계학술대회 논문집
• /
• pp.101-104
• /
• 2009

In this paper, it's described the techniques for the analysis of corona generated in open live parts of electric facilities. At needle-plane electrodes, when the voltage increased($0{\sim}70kV$, ramping 10kV) using the high voltage generation system(HIPOTRINICS $0{\sim}200kV$, USA), it's generated the partial discharge. There are compared between UV detected image and PD quantity. As these results, UV areas and gains are normalized. And electric facilities are evaluated the 5 steps such as 'good', 'recognition', 'check', 'inspection', 'change(replacement)'.

• 한국전기전자재료학회논문지
• /
• 제24권12호
• /
• pp.996-1001
• /
• 2011

A bushing is very important because it must supply the high voltage to the power equipment. Generally, the surface of bushing is contaminated with rain, dust, salt and others. A bushing with contaminations at air are serious problem in insulation. Therefore, it is important to understand the inspection and diagnoses of the safety. The ultra-violet rays(UV) camera has attracted interest from the view point of easy judgement. In this paper, we will report on the corona discharge characteristics on bushing model with contaminations. Also, UV images of discharge in air are analyzed using prototype UV camera of Korea. These results are studied at both AC and DC voltage under a non-uniform field.

• 천문학회지
• /
• 제55권3호
• /
• pp.67-74
• /
• 2022

In this study, we perform a statistical investigation of the kinematic classification of 4,264 coronal mass ejections (CMEs) from 1996 to 2015 observed by SOHO/LASCO C3. Using the constant acceleration model, we classify these CMEs into three groups: deceleration, constant velocity, and acceleration motion. For this, we devise three different classification methods using fractional speed variation, height contribution, and visual inspection. The main results of this study can be summarized as follows. First, the fractions of three groups depend on the method used. Second, about half of the events belong to the groups of acceleration and deceleration. Third, the fractions of three motion groups as a function of CME speed are consistent with one another. Fourth, the fraction of acceleration motion decreases as CME speed increases, while the fractions of other motions increase with speed. In addition, the acceleration motions are dominant in low speed CMEs whereas the constant velocity motions are dominant in high speed CMEs.

• 정보교육학회논문지
• /
• 제25권2호
• /
• pp.265-277
• /
• 2021

기술의 발전에 따라 디지털 리터러시의 개념이 기능과 도구 활용 중심에서 사회, 문화적 맥락에서 의사소통과 참여의 범위까지 확장되고 있다. 특히 코로나19와 같은 원격학습환경에서 학습자의 디지털 리터러시 역량은 더욱 중요하고 필요하다. 본 연구에서는 초등학교 교과서에 나타난 디지털 리터러시에 대한 분석과 점검을 통해 디지털 리터러시 교육 개선 방안에 대해 연구하였다. 이를 위해 디지털 리터러시를 구성하는 기초적 지식, 기술 및 역량으로 구성된 준거를 통해서 분석하였다. 연구 결과 초등학교 교과서의 디지털 리터러시 교육 내용은 기능과 도구 중심으로 제시되고, 특정 영역 등에 편중되어 있고 체계성, 연계성 등에서 부족한 부분이 발견되었다. 이에 초등 정보교과 독립을 통한 디지털 리터러시의 교과 체계 구성과 교육과정의 구체적인 구성 방안 및 예비교사의 실천 역량 강화를 위한 방안에 대해 제시하였다.