• The Journal of the Petrological Society of Korea
• /
• v.14 no.3 s.41
• /
• pp.127-140
• /
• 2005

The Samyuri area of Jeoksang-myeon, Muju-gun at the Middle Yeongnam Massif consists of granitic gneiss, porphyroblastic gneiss and leucocratic gneiss, which correspond to Precambrian Wonnam Series. Here we discuss a geochemical implication of the data based on major element composition, trace element, rare earth element (REE), Sm-Nd and Rb-Sr isotope systematics of the boring cores in the granite gneiss area. The boring cores are granitic gneiss (including biotite gneiss) and amphibolite. The major and trace element compositions of granitic gneiss and amphibolite suggest that the protolith belongs to TTG (Tonalite-Trondhjemite-Granodiorite) and tholeiitic series, respectively. Chondrte-normalized REE patterns vary in LREE, HREE and Eu anomalies. The granitic gneiss and amphibolite have Sm-Nd whole rock age of $2,026{\pm}230(2{\sigma})$ Ma with an initial Nd isotopic ratio of $0.50979{\pm}0.00028(2{\sigma})$ (initial ${\epsilon}_{Nd}=-4.4$), which suggests that the source material was derived from old crustal material. Particularly, this initial ${\epsilon}$ Nd value belongs to the range of the geochemical evolution of Archean basement in North-China Craton, and also corresponds to the initial Nd isotope evolution line by Lee et al. (2005). In addition, chondrite-normalized REE pattern and initial Nd value of amphibolite are very similar to those of juvenile magma in crustal formation process.

• Design & Manufacturing
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2020

In this study, the variation of the shrinkage in the thickness direction of the molded parts according to the gate size of the polymer core fabricated through the 3D printer using the SLS method was studied. The polymer cores are laser sintered and the powder material is nylon base PA2200. The polymer cores have lower heat transfer rate and rigidity than the metal core due to the characteristics of the material. Therefore, the injection molding test conditions are set to minimize the deformation of the core during the injection process. The resin used in the injection molding test is a PP material. The packing condition was set to 80, 90 and 100% of the maximum injection pressure for each gate size. The runner diameter used was ∅3mm, and the gates were fabricated in semicircle shapes with cross sections 1, 2, and 3 ㎟, respectively. Thickness measurement was performed for 10 points at 2.5 mm intervals from the point 2.5 mm away from the gate, and the shrinkage to thickness was measured for each point. The shrinkage rate according to the gate size tends to decrease as the cross-sectional area decreases as the maximum injection pressure increases. The average thickness shrinkage rate was close to 0% when the packing pressure was 90% for the gate area of 1mm2. When the holding pressure was set to 100%, the shrinkage was found to decrease by 3% from the standard dimension due to the over-packing phenomenon. Therefore, the smaller the gate, the more closely the molded dimensions can be molded due to the high pressure generation. It was confirmed that precise packing process control is necessary because over-packing phenomenon may occur.

• Applied Microscopy
• /
• v.17 no.1
• /
• pp.83-97
• /
• 1987

In order to discriminate the enteroendocrine cell types in the mucosal epithelium of the normal duodenum of the Korean hedgehog (Erinaceus koreanus). The tissues were fixed in the mixture of 1% paraformaldehyde and 1% glutaraldehyde in phosphate buffer (pH 7.2), and postfixed in 2% osmium tetroxide (phosphate buffer, pH 7.2). They were embedded in Araldite, and the ultrathin sections were made by LKB-V ultratome following the inspection of semithin sections stained with toluidine blue-borax solutions. Ultrathin sections contrasted with uranyl acetate and lead citrate were observed with JEM 100B electron microscope. At least six types of enteroendocrine cells distributed in the mucosal epithelium of the duodenum were identified according to their morphological characteristics mainly based on the size, shape, number and electron density of the secretory granules. Type I cells had moderately developed organelles. The secretory granules were pleomorphic ($370X510nm$), and the granule cores with high electron density were enveloped in limiting membrane and characterized by a narrow halo. Type II cells contained an indented nucleus and well-developed organelles. The secretory granules were round (350 nm) and classified in two kinds by electron density, moderate and high. Both granules were surrounded by limiting membrane and those with high electron density showed often a wide halo. Type III cells had an indented nucleus. The secretory granules with various electron density were round (220 nm) in shape. The granules with high electron density were enveloped in limiting membrane and characterized by a narrow halo, but those with low or moderate electron density had not been observed the limiting membrane. Type IV cells contained an indented nucleus and moderately developed organelles. The secretory granules were round (180 nm) in shape, and the granule cores with high electron density were enveloped in limiting membrane and showed often a wide halo. Type V cells had a large amount of rough endoplasmic reticulum. Secretory granules with low or moderate electron density were round (230 nm) in shape, and surrounded by limiting membrane and showed a narrow halo. Type VI cells contained an oval nucleus and well-developed organelles, especially Golgi complex. The secretory granules with high electron density were round (210 nm) in shape. The granules were enveloped in limiting membrane and showed often a wide halo.

• Journal of Technologic Dentistry
• /
• v.33 no.4
• /
• pp.299-306
• /
• 2011

Purpose: This study aimed to investigate the shear bond strength by manufacturing the veneering porcelain on the IPS e.max $ZirCAD^{(R)}$ zirconia core, using the layering technique and heat-pressing technique, and to evaluate the clinical stability by comparing to the conventional metal ceramic system. Methods: The Schmitz-Schulmeyer test method was used to evaluate the core-veneer shear bond strength of zirconia core ceramic(IPS e.max $ZirCAD^{(R)}$) and their manufacture recommended two veneering ceramic systems(IPS e.max $ceram^{(R)}$, IPS e. max $ZirPress^{(R)}$). A metal ceramic system(Bellabond $plus^{(R)}$, VITA $VM13^{(R)}$) was used as a control group for the two all ceramic system test groups. The maximum loading and shear bond strength was measured. The average shear strength(MPa) was analyzed with the one-way ANOVA and the Tukey's test(${\alpha}$=.05). The fracture specimens were examined using Microscope to determine the failure pattern. Results: The mean shear bond strengths(SD) in MPa were MBSB control 43.62(2.13); ZBSB 18.65(1.76); ZPSB 18.89(1.54). The shear strengths of the zirconia cores were not significantly different(P>.05). Microscope examination showed that zirconia specimens presented mixed failure, and base metal alloy specimens showed adhesive failure. Conclusion: There was no siginificant different between the layering technique and the heat pressing technique in the veneering methods on the zirconia cores. None of the zirconia core and veneering ceramics could attain the high bond strength values of the metal ceramic combination.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.490-498
• /
• 2020

In this study, the seismic performance of low-rise piloti buildings with eccentric core (shear wall) positions was analyzed and reviewed. A prototype was selected among constructed low-rise piloti buildings with eccentric cores designed based on KBC2005. The seismic performance of the building showed plastic behavior in the X-direction and elastic behavior in the Y-direction. The inter-story drift is larger than that of a concentric core case and has the maximum allowed drift ratio. The displacement ratio of the first story is much larger than that of upper stories, and the frame structure in the first story is vulnerable to lateral force. Therefore, low-rise piloti buildings with eccentric cores need to have less lateral displacement, as well as reinforcement of the lateral resistance capacity in seismic design and seismic retrofit.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.9
• /
• pp.691-698
• /
• 2006

TCP/IP Offload Engine (TOE) is a technology that processes TCP/IP on a network adapter instead of a host CPU to reduce protocol processing overhead from the host CPU. There have been some approaches to implementing TOE: software TOE based on an embedded processor; hardware TOE based on ASIC implementation; and hybrid TOE in which software and hardware functions are combined. In this paper, we designed software modules and hardware modules for a hybrid TOE on an FPGA that had two processor cores. Software modules are based on the embedded Linux. Hardware modules are for data transmission (TX) and reception (RX). One core controls the TX path and the other controls the RX path of the Linux. This TX/RX path separation mechanism can reduce task switching overheads between processes and overcome poor performance of single embedded processor. Hardware modules deal with creating headers for outgoing packets, processing headers of incoming packets, and fetching or storing data from or to the host memory by DMA. These can make it possible to improve the performance of data transmission and reception. We proved performance of the TOE with separated transmission and reception paths by performing experiments with a TOE network adapter that was equipped with the FPGA having processor cores.

• Journal of Radiation Protection and Research
• /
• v.42 no.2
• /
• pp.114-129
• /
• 2017

Background: The purpose of this paper is to confirm the event timings and the magnitude of fission product aerosol release from the Fukushima accident. Over a few hundreds of technical papers have been published on the environmental impact of Fukushima Daiichi accident since the accident occurred on March 11, 2011. However, most of the research used reverse or inverse method based on the monitoring of activities in the remote places and only few papers attempted to estimate the release of fission products from individual reactor core or from individual spent fuel pool. Severe accident analysis code can be used to estimate the radioactive release from which reactor core and from which radionuclide the peaks in monitoring points can be generated. Materials and Methods: The basic material used for this study are the initial core inventory obtained from the report JAEA-Data/Code 2012-018 and the given accident scenarios provided by Japanese Government or Tokyo Electric Power Company (TEPCO) in official reports. In this research a forward method using severe accident progression code is used as it might be useful for justifying the results of reverse or inverse method or vice versa. Results and Discussion: The release timing and amounts to the environment are estimated for volatile radioactive fission products such as noble gases, cesium, iodine, and tellurium up to 184 hours (about 7.7 days) after earthquake occurs. The in-plant fission product behaviors and release characteristics to environment are estimated using the severe accident progression analysis code, MELCOR, for Fukushima Daiichi accident. These results are compared with other research results which are summarized in UNSCEAR 2013 Report and other technical papers. Also it may provide the physically based arguments for justifying or suspecting the rationale for the scenarios provided in open literature. Conclusion: The estimated results by MELCOR code simulation of this study indicate that the release amount of volatile fission products to environment from Units 1, 2, and 3 cores is well within the range estimated by the reverse or inverse method, which are summarized in UNSCEAR 2013 report. But this does not necessarily mean that these two approaches are consistent.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.95-107
• /
• 2009

The purpose of this research was to examine the fitness of zirconia cores that were made by different sintering methods; generic electricity furnace and microwave furnace. Firstly, 12 cores for each group were made by using each different sintering process and attached them to a metal die with silicon. The internal and marginal gap of sintered zirconia was measured by using Skyscan 1076 micro-CT, then it was reorganized by CT-An software. To each samples, we extracted B-L image, M-D image of cutting side, and cross-sectional side of tooth long axis and calculated the mean value of marginal, axial, and occlusal gap each side. Results: 1. The mean marginal gap of sintered zirconia was $36.20{\mu}m$ for EVE, $47.67{\mu}m$ for LAV, $52.47{\mu}m$ for DEN, and $54.63{\mu}m$ for CER. 2. For the axial wall, the research showed the largest value of $63.49{\mu}m$ for EVE, but there were no statistical significance. 3. In related to the occlusal internal measurement, DEN showed the smallest value ($77.06{\mu}m$), EVE and CER showed significantly high value. From this study, it is suggested that CAD/CAM zirconia core which was made in the process of microwave sintering has clinically acceptable values in marginal and internal gap.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.6
• /
• pp.1-10
• /
• 2011

In designing multi-core processors, interconnection delay is one of the major constraints in performance improvement. To solve this problem, the 3-dimensional integration technology has been adopted in designing multi-core processors. The 3D multi-core architecture can reduce the physical wire length by stacking cores vertically, leading to reduced interconnection delay and reduced power consumption. However, the power density of 3D multi-core architecture is increased significantly compared to the traditional 2D multi-core architecture, resulting in the increased temperature of the processor. In this paper, the floorplan methods which change the forms of vertical placement of the core and the level-2 cache are analyzed to solve the thermal problems in 3D multi-core processors. According to the experimental results, it is an effective way to reduce the temperature in the processor that the core and the level-2 cache are stacked adjacently. Compared to the floorplan where cores are stacked adjacently to each other, the floorplan where the core is stacked adjacently to the level-2 cache can reduce the temperature by 22% in the case of 4-layers, and by 13% in the case of 2-layers.

• Journal of Korean Society of Forest Science
• /
• v.85 no.2
• /
• pp.260-270
• /
• 1996

Structure and dynamics of Pinus densiflora community in Mt. Kaya were studied to provide the information needed for management of Pinus densiflora forest in the southern inland of Korea. Stratification structure of Pinus densiflora community in the lower and middle slope consisted of tree layer(10~15m), subtree layer(4~10m), shrub layer(1~4m), and herb layer(below 1m), while in the rock zone of ridge and top area consisted of tree layer(7~10m), subtree layer(2~7m), shrub layer(1~2m), and herb layer(below 1m). According to the diameter distribution of tree species in Pinus densiflora community, secondary Pinus densiflora forest will gradually decline. Its forest may be replaced by Quercus mongolica, Quercus serrata, Carpinus laxiflora, C. cordata, and Fraxinus rhychophylla in the lower slope, and by Quercus mongolica in the middle slope. Pinus densiflora forest has its seedlings and saplings in ridge and top area, so it may be sustained. By taking cores from Pinus densiflora trees in research area, it could be obtained that in the lower and middle slope, age of Pinus densiflora forest was about 80~90 years old. When the age of its trees was about 72~80 years old, withering trees of standing dead occurred. Disturbance regime of Pinus densiflora community in Mt. Kaya consisted of standing dead, uprooting and limbfall, these were 70.6%, 17.6% and 11.8% respectively. It takes about 100~110 years for advance growth of Pinus densiflora in ridge and top area to reach tree layer. During the period, it has twice chances of disturbance in standing dead. Annual diameter growth of Pinus densiflora was 2.45~2.9mm in the lower and middle slope, while it was 1.75mm in ridge and top region, by measuring cores.