• Journal of Korean Society of Forest Science
• /
• v.99 no.5
• /
• pp.682-685
• /
• 2010

Coring has been widely used to measure annual increment in temperate forest ecosystems. This method is attractive because cores can be taken in just one visit. However, the accuracy of this method has not been tested. We expected coring to be less accurate than band dendrometers because of the eccentricity of tree growth. We studied 41 trees at the Long Term Experimental Forest in Mt. Gyebang, which has been monitored with band dendrometers since 1996. We collected two tree cores from the south and north face of each tree, 10 cm below the growth band. Increment cores were measured to 0.01 mm under stereomicroscopy. Annual growth from 1997 to 2006 was 3.2 mm $yr^{-1}$ for Quercus mongolica, 3.5 mm $yr^{-1}$ for Kalopanax septemlobus, and 5.7 mm $yr^{-1}$ for Pinus densiflora. The difference between the two methods was 10% for Q. mongolica, 14% for K. septemlobus, and 4% for P. densiflora. Compaction in the corer and shrinkage during drying decreased diameter increment by 5.6% and 1.0% on P. densiflora, respectively. This study suggests that the two methods for annual increment measurement are very similar, but species specificity should be concerned for direct comparison.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.10
• /
• pp.1025-1030
• /
• 2007

Three kinds of metallic sandwich panels with quasi-Kagome truss cores have been analyzed on their mechanical behaviors subjected to bending load. According to the results of previous work on the optimal design, they were designed to have similarly high strength per weight with the identical overall sizes, i.e., the total length, the width, the core height. Differences were in the face sheet thickness and/or the thickness of the metal sheet from which the core was fabricated through expanding and bending processes. Under the bending load, they performed well as designed, as far as the maximum load is concerned. However, after the maximum load, the load-displacement curves were different each other depending on the slenderness ratio of the truss elements composing the quasi-Kagome truss cores and the face sheet thickness. Namely, the slenderness ratio and the face sheet thickness governed stability of the elastic and plastic buckling. Therefore, if energy absorption characteristics or structural stability as well as the maximum load capacity are to be achieved, the sandwich panel with thick truss members and thick face sheet should be selected.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.610-612
• /
• 2008

Piston cores retrieved from the eastern part of the deep-water Ulleung Basin were analyzed to access the potential of hydrocarbon gas generation and natural gas hydrate (NGH) formation. Seismic data acquired in the study area were also analyzed to determine the presence of hydrocarbon gas and/or NGH, and to map their distribution. Core analyses revealed high total organic carbon (TOC) contents which favor hydrocarbon generation. The cores recovered from the southern study area showed the sufficient residual hydrocarbon gas concentrations for the formation of significant NGH. These cores also showed the cracks developed parallel to the bedding that suggest significant gas content in situ. A number of seismic blanking zones were observed on seismic data. They are identified as vertical to sub-vertical chimneys caused by the upward migration of pore fluid or gas, and containing of free gas and/or NGH. Often, they are associated with velocity pull-up structures that are interpreted to be the result of high-velocity NGH. The seismic data also showed several bottom-simulating reflectors (BSRs) that are associated with overlying NGH and underlying free gas. The distribution of blanking zones and BSRs would be impacted by the lateral differences of upward methane fluxes.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.3
• /
• pp.54-60
• /
• 2001

A newly designed inductive micro displacement detecting system is presented. The proposed inductive system consists of driving coils, position-detecting coils, cores, and closed-loop formed magnetic blocks. The cores and magnetic blocks are made of Mn-Zn ferrite. When AC sine wave is applied to the driving coils, the time derivative flux is generated within the system, and then induced voltages arise in the position-detecting coils according to the core\`s position. Putting the cores to be moved proportionally to the input displacement, the induced voltage is proportional to input displacement. The parameters that affect the system characteristics are turn ratio, air-gap size, excitation frequency, overlap area, load resistance, capacitance effect, and so forth. Based on the experimental results, the system parameters are selected in such a way as to have high sensitivity ad stable responses. The sensitivity of the proposed inductive displacement-detecting system is greater than 2800mV.V-1mm-1 and the linearity error is below $\pm$0.10% in the range of $\pm$200㎛.

• Journal of Power Electronics
• /
• v.8 no.3
• /
• pp.217-227
• /
• 2008

The electric power subsystems (EPS) of most remote sensing satellites consist of a solar array as a source of energy, a storage battery, a power management and control (PMC) unit and a charge equalization unit (CEU) for the storage battery. The PMC and CEU use high frequency transformers in their power modules. This paper presents a design, implementation and testing results of a high frequency transformer for the EPS of satellite applications. Two approaches are used in the design process of the transformer based on the pre-determined transformer specifications. The transformer is designed based on an ETD 29 ferrite core. The implemented transformer consists of one center-tapped primary coil with eleven center-tapped secondary coils. The offline calculation results and measured values of R, L for transformer coils are convergence. A test circuit for measuring the transformer parameters like voltage, current and B-H hysteresis was implemented and applied. The test results confirm that the voltage waveforms of both primary and secondary coils were as desired. No overlapping occurred between the control signal and the transformer, which was not saturated during testing even during a short circuit test of the secondary channels. The dynamic B-H loop characteristics of the used transformer cores were measured. The sample test results are given in this paper.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.2
• /
• pp.355-364
• /
• 2008

The Buckling-Restrained Braces (BRB) has been developed to inhibit buckling and exhibit stable behavior under both tensile and compressive cycles. In this study, an experimental has been conducted by using the strength of its members and loading protocols as parameters to evaluate the structural performance of BRB (without in-filled concrete). Specimens are composed of an inner core and an outer tube with different steel strengths. When high-strength steels were used as inner cores, the ductility of BRB decreasedm and the requirements (Cumulative Plastic Ductility) of the AISC Seismic Provisions were not satisfied. However, when high-strength steels were used as inner cores instead of conventional strength steel cores, the maximum capacity increased significantly and displayed similar performance in total energy dissipation.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.4
• /
• pp.25-33
• /
• 2014

This paper proposes a power-efficient scheduling scheme that stochastically minimizes the power consumption of real-time tasks while meeting their deadlines on multicore processors. In the proposed scheme, uncertain computation amounts of given tasks are translated into probabilistic computation amounts based on their past completion amounts, and the mean power consumption of the translated probabilistic computation amounts is minimized with a finite set of discrete clock frequencies. Also, when system load is low, the proposed scheme activates a part of all available cores with unused cores powered off, considering the leakage power consumption of cores. Evaluation shows that the scheme saves up to 69% power consumption of the previous method.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.5
• /
• pp.415-422
• /
• 2014

PURPOSE. The purpose of this study was to evaluate and compare the translucency of shaded zirconia allceramic systems. MATERIALS AND METHODS. Translucency of 3 different zirconia all-ceramic systems colored by different techniques was compared with a lithium disilicate glass-ceramic (IPS e.max Press). Square-shaped specimens with 0.5 mm thickness were fabricated from In-Ceram YZ, ICE Zirkon and Katana systems in A1, A2 and A3.5 shades according to Vitapan Classical shade tab (n=11). Specimens were then veneered and glazed with corresponding veneer ceramic recommended by each zirconia system manufacturer and the total thickness was set to 1.5 mm. Translucency measurements were performed with VITA Easyshade Compact spectrophotometer after each stage and translucency parameter was calculated. Data were statistically analyzed with repeated measures ANOVA and Tukey multiple comparison test. RESULTS. The control group was significantly more translucent than the zirconia systems (P<.05). ICE Zirkon cores showed the least translucency; neither In-Ceram YZ nor Katana systems were superior to each other in terms of translucency. Translucency of all specimens was decreased after veneering, and the translucency rankings were changed. CONCLUSION. Coloring technique did not have a significant effect on translucency of zirconia cores. Although zirconia systems were less translucent than lithium disilicate glass ceramic, they had partial translucency and there were translucency differences among the zirconia systems. Chroma affected the translucency of precolored zirconia cores.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.9
• /
• pp.643-651
• /
• 2001

Fused vertical directional coupler switches (FVCSs) with switching operation induced section (SOIS) and extinction ratio enhanced section (ERES) are proposed. In these FVCSs, switching operation is achieved by changing the refractive indices of both cores in SOIS and improvement of extinction ratios larger than 30dB for both cross and bar states is achieved by controlling the asymmetry of refractive indices between both cores in ERES. In addition, the design guidelines to have high extinction ratios larger than 30dB with large tolerances of the refractive index of cores are presented.

• Journal of The Korean Astronomical Society
• /
• v.40 no.4
• /
• pp.157-160
• /
• 2007

I present a model to explain the mass segregation and shallow mass functions observed in the central parts of starburst stellar clusters. The model assumes that the initial pre-stellar cores mass function resulting from the turbulent fragmentation of the proto-cluster cloud is significantly altered by the cores coalescence before they collapse to form stars. With appropriate, yet realistic parameters, this model based on the competition between cores coalescence and collapse reproduces the mass spectra of the well studied Arches cluster. Namely, the slopes at the intermediate and high mass ends, as well as the peculiar bump observed at $6M_{\bigodot}$. This coalescence-collapse process occurs on a short timescale of the order of the free fall time of the proto-cluster cloud (i.e., a few $10^4$ years), suggesting that mass segregation in Arches and similar clusters is primordial. The best fitting model implies the total mass of the Arches cluster is $1.45{\times}10^5M_{\bigodot}$, which is slightly higher than the often quoted, but completeness affected, observational value of a few $10^4M_{\bigodot}$. The model implies a star formation efficiency of ${\sim}30$ percent which implies that the Arches cluster is likely to a gravitationally bound system.