• Textile Coloration and Finishing
• /
• v.18 no.1
• /
• pp.33-43
• /
• 2006

The purpose of this study was to eximine the effect of different yam twisting methods on mechanical properties and 3D CAD images of plain knitted fabrics made of composite yarns. Six yams were used in this study: four different composite yams of the six consist of acetate and functional polyester (Poly-m) with the ratio of 70:30, and the rest two are the original acetate $100\%$ yam and the poly-m $100\%$ yarn. The four kinds of composite yarns were processed in combinations of twisting processes such as interlacing, false twisting, two for one twisting, combined twisting and single covering, and the two original yams were knitted without any twisting process. Sixteen mechanical properties of all the six knitted fabrics, knitted under the same knitting conditions, were measured by KES-FB system with the outer knit condition. The results were as follows; 1) When the sample applied with the false twisting process at the temperature as high as $220^{\circ}C$, ENT, B, HB, G and RC values of samples increased which leads to increasing dimensional stability. 2) To gain the high bending and shear properties in the single covering process, selecting the core yarn with such properties is the most important factor. 3) Interlacing process effected to increase RC value. 4) False twisting process after interlacing process gave bulkiness and un-interlaced part in yam was increased SMD value. The SMD value of the kilted fabric of the composite yarn, which was put through the combined twist process, was higher than those of which simple process such as the two for one twist or the single covering process applied. In order to achieve the silk-like surface feel of knitted fabric, the sin91e covering process is recommended. 5) Examining the simulation images of the knifed fabrics of composite yarn, which were generated by the 3D CAD system based on the mechanical properties of the fabric, led that appearance could be changed as different twisting methods were applied.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.10
• /
• pp.95-104
• /
• 2004

This paper propose a motion estimator architecture to reduce the power consumption of the most-power-consuming motion estimation method when designing multimedia SoC with deep submicron technologies below 0.13${\mu}{\textrm}{m}$. The proposed architecture considers both dynamic and static power consumption so that it is suitable for large leakage process technologies, while conventional architectures consider only dynamic power consumption. Consequently, it is suitable for mobile information terminals such as mobile videophone where efficient power management is essential. It exploits full search method for simple hardware implementation. It also exploits early break-off method to reduce dynamic power consumption. To reduce static power consumption, megablock shutdown method considering power line noise is also employed. To evaluate the proposed architecture when applied multimedia SoC, system-level control flow and low-power control algorithm are developed and the power consumption was calculated based on thor From the simulation results, power consumption was reduced to about 60%. Considering the line width reduction and increased leakage current due to heat dissipation in chip core, the proposed architecture shows steady power reduction while it goes worse in conventional architectures.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.70-77
• /
• 2013

We suggest a low area and high efficiency switched-mode power supply (SMPS) with a pulse width modulation (PWM) generator based on a pseudo relaxation-oscillating technique. In the proposed circuit, the PWM duty ratio is determined by the voltage slope control of an internal capacitor according to amount of charging current in a PWM generator. Compared to conventional SMPSs, the proposed control method consists of a simple structure without the filter circuits needed for an analog-controlled SMPS or the digital compensator used by a digitally-controlled SMPS. The proposed circuit is able to operate at switching frequency of 1MHz~10MHz, as this frequency can be controlled from the selection of one of the internal capacitors in a PWM generator. The maximum current of the core circuit is 2.7 mA, and the total current of the entire circuit including output buffer driver is 15 mA at 10 MHz switching frequency. The proposed SMPS has a simulated maximum ripple voltage of 7mV. In this paper, to verify the operation of the proposed circuit, we performed simulation using Dongbu Hitek BCD $0.35{\mu}m$ technology and measured the proposed circuit.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.480-480
• /
• 2008

Vacuum circuit breaker(VCB) is now emerging as an alternative of gas circuit breaker(GCB) which uses SF6 gas as insulating material whose dielectric strength is outstanding. But we have to reduce SF6 gas because SF6 gas is one of greenhouse gas and efforts to reduce greenhouse gas are now trend of the world. Therefore, we can say VCB is the optimal alternative of GCB because vacuum is environmentally friendly. The vacuum interrupter is the core part of VCB to interrupt arcing current. There are mainly two methods to extinguish arc. One is radial magnetic field (RMF) method and the other is axial magnetic field (AMF) method. We deals with RMF method in this paper. Compared with AMP, RMF arc quenching method has different principle to extinguish arc. In case of RMF method, pinch effect is much larger than AMF method. Because of pinch effect RMF type contact electrodes have the single large spot which is severly damaged and melted while AMF type contact electrodes have small and multiple spots which are slightly damaged and melted. To prevent contact electrode being damaged and melted from high temperature-arc, RMF method uses Lorentz force to move arc. In this paper we calculated and compared the arc driving force of two cases and we analyzed the force acting on each part of arc by means of commercial finite element method software Maxwell 3D. They have 3petals and we considered two cases. One is the case when fixed(upper) and movable(lower) contacts are in mirror arrangement (Case 1). The other is the case when one of two contacts (movable contact) is revolved at maximum angle as possible as it can be (Case 2). And at each case above, we analyzed arc driving force at two positions, position 1 is the closest to the center of contact and position 2 is near the edge of petal on fixed contact. As a result we could find that Case 2 generated stronger arc driving force than Case 1 at position 1. But at position 2 Case 1 generated stronger arc driving force than Case 2. This simulation method can contribute to optimizing spiral-type electrode designs in a view of arc driving force.

• The KIPS Transactions:PartA
• /
• v.12A no.4 s.94
• /
• pp.305-312
• /
• 2005

In this paper, we present algorithm-level techniques for energy-efficient design at the algorithm level using FPGAs. We then use these techniques to create energy-efficient designs for two signal processing kernel applications: fast Fourier transform(FFT) and matrix multiplication. We evaluate the performance, in terms of both latency and energy efficiency, of FPGAs in performing these tasks. Using a Xilinx Virtex-II as the target FPGA, we compare the performance of our designs to those from the Xilinx library as well as to conventional algorithms run on the PowerPC core embedded in the Virtex-II Pro and the Texas Instruments TMS320C6415. Our evaluations are done both through estimation based on energy and latency equations on high-level and through low-level simulation. For FFT, our designs dissipated an average of $50\%$ less energy than the design from the Xilinx library and $56\%$ less than the DSP. Our designs showed an EAT factor of 10 times improvement over the embedded processor. These results provide a concrete evidence to substantiate the idea that FPGAs can outperform DSPs and embedded processors in signal processing. Further, they show that PFGAs can achieve this performance while still dissipating less energy than the other two types of devices.

• Tunnel and Underground Space
• /
• v.15 no.2 s.55
• /
• pp.119-128
• /
• 2005

Although the evaluation of the mechanical properties and behavior of jointed rock masses is very important for the design of tunnel and underground openings, it has always been considered the most difficult problem. One of the difficulties in describing the rock mass behavior is the selection of the appropriate constitutive model. This limitation may be overcome with the progress in discrete element software such as PFC, which does not need the user to prescribe a constitutive model for rock mass. In this paper, a 30\;m\;\times\;30\;m\;\times\;30\;m m jointed rock mass of road tunnel site was analyzed. h discrete fracture network was developed from the joint geometry obtained from core logging and surface survey. Using the discontinuities geometry from the DFN model, PFC simulations were carried out, starting with the intact rock and systematically adding the joints and the stress-strain response was recorded for each case. With the stress-strain response curves, the mechanical properties of jointed rock masses were determined. As expected, the presence of joints had a pronounced effect on mechanical properties of the rock mass. More importantly, getting the mechanical response of the PFC model doesn't require a user specified constitutive model.

• Journal of Internet Computing and Services
• /
• v.11 no.1
• /
• pp.35-48
• /
• 2010

For the next generation mobile communication system, diverse wireless network techniques such as beyond 3G LTE, WiMAX/WiBro, and next generation WLAN etc. are proceeding to the form integrated into the All-IP core network. According to this development, Beyond 3G integrated into heterogeneous wireless access technologies must support the vertical handover and network to be used of several radio networks. However, unified management of each network is demanded since it is individually serviced. Therefore, in order to solve this problem this study is introducing the theory of Common Radio Resource Management (CRRM) based on Generic Link Layer (GLL). This study designs the structure and functions to support the vertical handover and propose the vertical handover algorithm of which policy-based and MCDM are composed between LTE and WLAN systems using GLL and CRRM. Finally, simulation results are presented to show the improved performance over the data throughput, handover success rate and the system service cost.

• The Journal of Korean Institute of Next Generation Computing
• /
• v.15 no.2
• /
• pp.39-49
• /
• 2019

Recently, CPU-GPU integrated heterogeneous multicore processors have been widely used for improving the performance of computing systems. Heterogeneous multicore processors integrate CPUs and GPUs on a single chip where CPUs and GPUs share the LLC(Last Level Cache). This causes a serious cache contention problem inside the processor, resulting in significant performance degradation. In this paper, we propose the partitioned LLC architecture to solve the cache contention problem in heterogeneous multicore processors. We analyze the performance impact varying the LLC size of CPUs and GPUs, respectively. According to our simulation results, the bigger the LLC size of the CPU, the CPU performance improves by up to 21%. However, the GPU shows negligible performance difference when the assigned LLC size increases. In other words, the GPU is less likely to lose the performance when the LLC size decreases. Because the performance degradation due to the LLC size reduction in GPU is much smaller than the performance improvement due to the increase of the LLC size of the CPU, the overall performance of heterogeneous multicore processors is expected to be improved by applying partitioned LLC to CPUs and GPUs. In addition, if we develop a memory management technique that can maximize the performance of each core in the future, we can greatly improve the performance of heterogeneous multicore processors.

• Science of Emotion and Sensibility
• /
• v.24 no.2
• /
• pp.81-92
• /
• 2021

In this study, we investigated the effects of five EMS lumbar back pressure belts produced on an anatomical basis on lumbar spine stabilization. Five core muscles were selected, including the urinal, vertebral column, endotracheal, external abdominal, and large back muscles, and patterns were designed using a conductive fabric considering the appropriate muscle shape and pain-causing points. We experimented with four motions to examine the effects of different EMS abdominal compression belts on lumbar spine stabilization. Five healthy men in their 20s were selected. The selection conditions include no back pain history for the past three months, no restricted movements through pre-inspection, and the muscular strength of the body should belong to the normal grade. Using SLR, the sequence of experimental actions was chosen from the following but not limited to left-hand, body-hand, and back-line forces. Resting between movements lasted for 2 min, and the experiments were conducted after wearing the EMS abdominal pressure belt. Electrical stimulation was applied for 10 min to increase blood flow and muscle activation. The statistics of the experimental results were analyzed for specific differences by conducting the Wilcoxon and Friedman tests with nonparametric tests. The ranking results of each pattern were successfully assessed in the order of 5, 4, 3, 1, 2 for the five patterns, and we could identify slightly more significant results for experimental behavior associated with each muscle movement. Patterns produced based on anatomy showed differentiated effects when electric stimulation was applied to each muscle in different shapes, which could improve the stabilization of the lumbar spine in everyday life or training to the public. Based on these results, subsequent research would focus on developing smart healthcare clothing that is practical in daily life by employing different anatomical mechanisms, depending on the back pain, to utilize trunk-type tights.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.5
• /
• pp.646-654
• /
• 2020

This paper is to develop an electromagnetic wave-based sensor that can measure the spatial distribution of precipitation, and to a electromagnetic wave rain gauge (hereinafter, "EWRG") capable of simultaneously measuring rainfall, snowfall, and wind field, which are the core of heavy rain observation. Through this study, the LFM transmission and reception signals were theoretically analyzed. In addition, In order to develop a radar transceiver, LFM transceiver design and simulation were conducted. In this paper, we developed a K-BAND pulse-driven 6W SSPA(Solid State Power Amplifiers) transceiver using a small HMIC(Hybrid Microwave Integrated Circuit). It has more than 6W of output power and less than 5dB of receiving NF(Noise Figure) with short duty of 1% in high temperature environment of 65 degrees. The manufactured module emits LFM and Square Pulse waveform with the built-in waveform generator, and the receiver has more than 40dB of gain. The transceiver developed in this paper can be applied to the other small weather radar.