• Journal of Nutrition and Health
• /
• 제28권2호
• /
• pp.127-136
• /
• 1995

In this study, the nutritional composition of colostrum milk obtained from 22 mothers delivering perterm infants and 17 mothers delivering term infants was analyzed. The energy content of colostrum was yielded based on nitrogen, lactose, and lipid data. Preterm milk is more close the nutritional needs of the preterm infant than dose other breast milk. The results are as follows : 1) Protein concentration was significantly higher, but carbohydrate and lipid concentration were lower in preterm milk than fullterm milk. Energy content yielded from total nitrogen, lactose and lipid concentration was higher in the fullterm milk than preterm milk. 2) Calcium was higher in the preterm milk than fullterm colostrum. Phosphate was lower in fullterm milk than pretem milk. Calcium/Phosphate ratio were 2.61/1 in the preterm and 2.06/1 in the fullterm milk. Magnesium was higher in the preterm milk than fullterm milk. Zinc, Copper and Manganese concentrations were tended to lower in the preterm milk than fullterm milk.

• Bulletin of the Korean Chemical Society
• /
• 제35권6호
• /
• pp.1605-1612
• /
• 2014

Copper(I)-catalyzed Huisgen cycloaddition of terminal alkynes with unmasked azidoamines derived from amino acids is described. The reported strategy provides a new entry to highly hindered ${\beta}$-amino 1,2,3-triazole derivatives bearing a gem-diaryl group, which are potentially valuable entities as molecular catalysts for asymmetric transformations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 학술대회 논문집 전문대학교육위원
• /
• pp.22-25
• /
• 2000

Time dependent ozone generation characteristics of some oxide layers grown by ozone on the surface of corona discharge wires have been investigated experimentally in air ambience. Four wires of stainless steel, iron, silver and copper were used for the corona discharge wire of an ozone generator. And the effect of the metal oxide layers on ozone generation was studied and the contamination morphology of each layers was characterized. With the SEM images and the EDS spectra, it was found that all the surface of the corona wire were oxidized by the generated ozone and contaminated by airborne particles through the gradient force. As a result, the morphology and the electrical property of metal oxide layer grown on corona wire surface influenced on ozone generation characteristics i.e. discharge mechanisms.

• 한국전기전자재료학회논문지
• /
• 제21권10호
• /
• pp.930-933
• /
• 2008

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET device was made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40 nm, and the channel length was $50{\mu}m$, channel width was 3 mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.410-411
• /
• 2008

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET device was made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40nm, and the channel length was $50{\mu}m$, channel width was 3mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1020-1024
• /
• 1997

Recently the use of ceramic materals has been greatly increased in the industries. But machining of the ceramics is quite unproductive because of their high stength,high hardness,and brittleness. The efficiency of the grinding operation of ceramics depends on the preparation of diamond grinding wheel, i.e.,truning and dressing. This paper describes some experimental results on the dressing conditions of diamond grinding wheel. The dressing performance is evaluated by the magnitude of normal grinding force. The better dressed wheels result in the lower normal grinding forces. The dressing performances of copper plate and aluminum oxide dressing stick are compared. The optimum dressing conditions including the grit size of dressing sticks, the depth of the dressing operation, and the dressing speed qre determined.

• 마이크로전자및패키징학회지
• /
• 제21권2호
• /
• pp.23-29
• /
• 2014

Less power consumption, lower cost, smaller size and more functionality are the increasing demands for consumer electronic devices. The three dimensional(3-D) TSV packaging technology is the potential solution to meet this requirement because it can supply short vertical interconnects and high input/output(I/O) counts. Cu(Copper) has usually been chosen to fill the TSV because of its high conductivity, low cost and good compatibility with the multilayer interconnects process. However, the CTE mismatch and Cu ion drift under thermal stress can raise reliability issues. This study discribe the thermal stress reliability trend for successful implementation of 3-D packaging.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.42-46
• /
• 2000

In this paper, joints of Cu-1Cr-0.1Zr alloy to STS316L were performed by friction welding method. Cu-1Cr-0.1Zr alloy is attractive candidate as nuclear power plant material and exibit the best combination of high sts good electrical and thermal conductivity of any copper alloy examined. The stainless steel is a structural material who alloy acts as a heat sink material for the surface heat flux in the first wall. So, in this paper, not only the develop optimizing of friction welding with more reliability and more applicabililty but also the development of in-process rear quility(such as strength and toughness) evaluation technique by acoustic emission for friction welding of such nuclear component of Cu-1Cr-0.1Zr alloy to STS316L steel were performed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.40-42
• /
• 1999

In this paper, light-weight system of linear induction motor(LIM) for light railway train is presented, and is compared with former type of LIM. For the light-weight system without modification of motor size the material of primary core(silicon steel) is changed with iron-cobalt alloy and the material of primary winding(copper) is changed with aluminium. The characteristics of LIM are analyzed. Specially, the air gap magnetic flux density distribution due to end effect is showed with motor velocity, we will present papers continuously through designing and testing a trial product.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.24-26
• /
• 1995

The Development of A.C. Induction Motor for Railway Rolling Stock. The traction motor is designed as 4-pole induction motor with self ventilation. The winding insulation is throughout of materials of class C. The rotor is designed as a squrrel rotor with copper bar and casting. The rotor speed is detected by means of a pulse generator. The newer tection motor have no casting(frame). Punched-in holes make up the air duct and transfer the heat losses in complete. Maximim motor rpm is higher due to rotor construction. New is the entry of water-cooled traction motors in urban, However the water cooling design in - unfortunately - not applicable in traction motor.