• Journal of information and communication convergence engineering
• /
• v.15 no.4
• /
• pp.199-204
• /
• 2017

A compact dual-band half-ring-shaped (HRS) bent slot antenna fed by a coplanar waveguide for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) applications is presented. The antenna consists of two HRS slots with different lengths and widths. The two HRS slots are connected through an arc-shaped slit, and the upper HRS slot is bent in order to reduce the size of the antenna. The optimized dual-band HRS bent slot antenna operating in the 2.45 GHz WLAN and 3.5 GHz WiMAX bands is fabricated on an FR4 substrate with dimensions of 30 mm by 30 mm. The slot length of the proposed dual-band slot antenna is reduced by 35%, compared to a conventional dual-band rectangular slot antenna. Experimental results show that the proposed antenna operates in the frequency bands of 2.40-2.49 GHz and 3.39-3.72 GHz for a voltage standing wave ratio of less than 2, and measured gain is larger than 1.4 dBi in the two bands.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.616-619
• /
• 2003

This work presents the design, fabrication and microwave performance of distributed analog phase shifter (DAPS) fabricated on $(Ba,\;Sr)TiO_3$ (BST) thin films for X-band applications. Ferroelectric BST thin films were deposited on MgO substrates by pulsed laser deposition. The DAPS consists of high impedance coplanar waveguide (CPW) and periodically loaded tunable BST interdigitated capacitors (IDC). In order to reduce the insertion loss of DAPS and to remove the alteration of unloaded CPW properties according to an applied dc bias voltage, BST layer under transmission lines were removed by photolithography and RF-ion milling. The measured results are in good agreement with the simulated results at the frequencies of interest. The measured differential phase shift based on BST thin films was $24^{\circ}$ and the insertion loss decreased from 1.1 dB to 0.7 dB with increasing the bias voltage from 0 to 40V at 10 GHz.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1125-1128
• /
• 2003

This paper presents the design method of a Colpitts type oscillator with coplanar waveguide(CPW) structures in the range of Ka-band frequency for transmitter and receiver modules. Series short stubs of CPW patterns provide inductances and capacitances in the range of Ka-band which can be expressed as a CLC-$\pi$ equivalent circuit. The experimentation has employed ro4003 substrates as a CPW substrate which has a dielectric constant of 3.38 and a signal and ground space of 100um. A method of momentum simulation for the CPW patterns has performed with an ADS software tool of Hewlett-Packard Corp. Inductance and capacitance circuits of a Colpitts oscillator was interconnected to a MESFET with CPW bend structures of including the input and output impedance matching circuits of the active transistor. Circuit parameters for impedance matching were determined through the network conversion to the equivalent length of CPW transmission lines by using T-network 1 $\pi$-network conversion circuit. A Colpitts oscillator was fabricated on the substrate of a area of 8.5mm x 17.4mm with a MESFET of Fujitsu FMM5704X and CPW series short stubs. The design suggested the possibility of realizing oscillators on a planar surface for the wireless system of tansmitter and receiver modules in the frequency range of 30GHz

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.90-98
• /
• 1999

This paper presents a wideband single-balanced mixer using a diode which can be used in RF receiver of microwave measurement systems. For wideband characteristic, local oscillator(LO) signal is provided to diode with low loss using a coplanar waveguide-to-slotline balun. For high isolation characteristic radio frequency (RF) port and intermediate frequency (IF) port are designed using directional coupler. This mixer presents 30.5~31.17dB conversion loss whose flatness is within 1dB for 9 kHz~2.6 GHz wideband RF signal, and above 30 dB isolation for LO signal.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.74-79
• /
• 2002

High-speed probe made to test single flux quantum(SFQ) circuits was comprised of semi-rigid coaxial cables and microstrip lines. The impedance was set at 50 $\Omega$to carry high-speed signals without much loss. To do performance test of high-speed probe, we have attempted to fabricate a test chip which has a coplanar waveguide(CPW) structure. Electromagnetic simulation was done to optimize the dimension of CPW so that the CPW structure has an impedance of 50$\Omega$, matching in impedance with the probe. We also used the simulation to investigate the effect of the width of signal line and the gap between signal line and ground plane to the characteristics of CPW structure. We fabricated the CPW structure with a gold film deposited on Si wafer whose resistivity was above $1.5\times$10$_4$$\Omega$.cm. The magnitudes of S／sub 21／ of CPW at 6 ㎓ in simulations and in the actual measurements done with a network analyzer were: -0.1 ㏈ and -0.33 ㏈ (type A),-0.2 ㏈ and -0.48 ㏈ (type B), respectively. Using the test chip, we have successfully tested the performance of high-speed probe made for SFQ circuits. The probe showed the good performance overthe bandwidth of 10 ㎓.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.5
• /
• pp.486-487
• /
• 1997

This paper presents the pure capacitive lumped element equivalent circuits for several coplanar waveguide(CPW) discontinuities such as an open-end, an open-end with connected ground planes, a gap and an open-end CPW stub and gives their capacitive element values as a function of physical dimensions of the discontinuity and the frequency for a specific substrate. The capacitive element values are determined from the scattering parameters which are obtained using the finite-difference time-domain(FDTD) method. For an open-end, an open-end with connected ground planes and a gap, the numerical results of the FDTD are compared with the quasi-static results which are calculated using the three- dimensional finite difference method(3D-FDM).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1321-1328
• /
• 2003

In this paper, we demonstrate that the directivity of the CPW(Coplanar Waveguide) directional coupler with finite-extent backed conductor is enhanced by eliminating center region of backed conductor appropriately. If the backed conductor is removed at center region of couplers, the couplers have two backed conductors. If effective odd mode dielectric constant is decreased at center region, the electrical length for odd mode is changed and phase velocity is same at the directional couplers. Hence, directivity is improved. The eliminated length is solved by an odd and even mode analysis. The designed moderate CPW directional coupler with the proposed compensation structure has excellent directivity and matching characteristic at center frequency in simulation and measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.368-378
• /
• 2004

In this paper, we proposed the compensation structures for the enhanced directivity of CPW(Coplanar waveguide) directional couplers with finite-extent backed conductor. The proposed compensation structures are. realized by expanding the slot width between signal line and ground plane in center region of couplers. The CPW couplers with expanded slot have the same phase velocity for even and odd mode because of added inductance and changed capacitance appropriately, so the enhanced directivity is accomplished. The designed CPW directional couplers have good directivity and matching characteristic at center frequency in simulation and measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1371-1379
• /
• 2010

This paper presents an analysis of impulse dispersion for impulse radio ultra-wide band(IR-UWB) antenna. A set of antenna structure configurations are highlighted with verification based on the STFT(Short Time Fourier Transform) in 3.1~5.1 GHz: first, a taper-slotted antenna allowing the optimal impulse transmission, and second, 4 types of the omni-directional IR-UWB antenna using different feed structures(microstrip line, and CPW(Coplanar Waveguide)). The proposed STFT allows the analysis of the IR-UWB antenna's dispersion characteristic.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1632-1638
• /
• 2008

This paper presents a method to design CPW (coplanar waveguide) balanced amplifiers using the existing CPW wilkinson balun. In order to realize the required power dividing/combining structure for balanced amplifiers, the CPP wilkinson balun is adopted. The proposed CPW balanced amplifier has much better matching performances than the CPW single-ended amplifier. The measured frequency bands, where the input and output reflection coefficients are less than -10dB, are $1.2{\sim}2.75GHz$ and $1{\sim}3.25GHz$, respectively, while the CPW single-ended amplifier has severely bad ones.