• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1248-1253
• /
• 2008

The MCS(Micro-Coplanar Strip) line with ground has been analyzed. The conformal mapping method is used to calculate the quasi-static effective dielectric constant and characteristic impedance of this MCS line. The computed results of the present work are found to be in good agreement when compared with the results obtained using commercial S/W, IE3D. And in this paper, the stepped-impedance low pass filter is designed and fabricated with MCS lines for improving the frequency responses. The LPF proposed structure has been also designed and implemented to have the sharp attenuation characteristics in stop band. The agreement between simulation and measurement results verify the implemented LPF.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.74-78
• /
• 2006

A non-integrated type noise filter on a Coplanar Waveguide (CPW) transmission line is demonstrated by using a highly resistive $Co_{41}Fe_{38}Al_{13}O_8$ nanogranular thin film with the dimensions of $4\;mm (\iota)\times4\;mm(\omega)\times0.1\;{\mu}m(t)$. The noise suppression characteristics are evaluated without placing an insulating layer between the CPW line and the magnetic thin film. The insertion loss is very low being less than 0.3 dB and this low value is maintained up to 2 GHz. At a ferromagnetic resonance frequency of 3.3 GHz, the power loss is very large and the degree of noise attenuation is measured to be 3 dB. This level of noise attenuation is still small for real applications; however, considering the small magnetic volume used in this work, further improvement is expected by simply increasing the magnetic volume and by integrating the magnetic thin film into the CPW transmission line.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.401-404
• /
• 2002

This paper proposes a new symmetrical bandpass filter based on capacitive loading with a coplanar waveguide (CPW) structure. The filter was numerically designed at the operating frequency around 2 ㎓ by using IE3D software package. The characteristics of the proposed filter were then measured which the results were in good agreement with simulation. The passband insertion loss was considerably low (~3 ㏈) and the return loss was high (greater than 10 ㏈). The size of the proposed filter was also decreased approximately 50% when comparing with the fitters using conventional transmission lines.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.111-114
• /
• 2005

The isolation performance of the S-band single-pole single-throw (SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide (GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9dB is obtained with the coplanar wire-bond interconnection (CWBI) at 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion (IMD3) are less than 2.43 dB over 2.5 CHz $\sim$ 4 GHz and greater than 64 dBc.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.3
• /
• pp.116-120
• /
• 2015

In this paper, a step type driver dipole antenna with a tapered balance and unbalance (balun) by a coplanar waveguide (CPW) to coplanar strip (CPS) transition is proposed. The proposed antenna consisted of step type driver, a CPW to CPS transition and tapered balun. The proposed antenna is realized the multi and wide resonate frequency band to introduce the step type driver and tapered balun. The step type driver is acted as a director too. This antenna could be more easily designed than the conventional printed quasi-Yagi dipole antenna. The operating frequency bandwidth was 650 [MHz] (2.65~3.3 GHz), 900 [MHz] (4.7~5.6 GHz) under a return-loss criterion of less than 10 dB. The measurements of the proposed antenna exhibited good results in the wideband operating frequency and radiation pattern. The proposed antenna can support wireless communications applications.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.53-55
• /
• 2011

The printed wide band monopole antenna having characteristics of dipole by modified coplanar wave guide(CPW) ground plane is presented. We are called a slot-arm printed monopole antenna and investigated the effect of the surface currents of the radiator on ground plane. The proposed antenna is treated as two asymmetric dipoles with the included angle of $90^{\circ}$ degrees which lie along Z-direction symmetrically. It is observed that the effect of the surface currents on the radiation patterns is similar to that of the corresponding dipole. The length and width of the ground plane correspond the radius and length of the dipole respectively. This approach is also valid to general printed monopole antennas. The simulation impedance bandwidth of the proposed antenna the range of 2.4 to 4.6 [GHz] for a voltage stand wave ratio (VSWR)${\leq}$2 and got pick gain of 6 [dBi]. So the proposed antenna is satisfied the requirement of the industry science medical (ISM) band operation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1129-1132
• /
• 2005

The purpose of this reserch is to establish the new design technology for microwave Coplanar structure. The components in microwave circuit are classified to transmission devices, EM devices, and quasi-TEM devices. After design of these devices, we analyzed these CPWs electromagnetically using FDTD method, and suggested optimum CPW structure. In oder to realize a CPW module up to 30 GHz-100 GHz band, we research on a technology of 3-dimensional microwave CPW, and GaAs substrate with Si layer for ohmic loss. As a result this research, we suppressed the leakage, resonance, coupling, and radiation of CPW EMI, and improved resonance quality of CPW.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.8
• /
• pp.41-48
• /
• 1992

The characteristics of traveling-wave electrodes for high-frequency electroptic integrated devices are described from the view point of improvement of phase-matching based on the conformal mapping method. Specific calculations of the characteristic impedance, effective microwave index, and eletrode loss for asymmetric coplanar strip(ACPS) and coplanar waveguide(CPW) electrode structures are presented as a function of the geometric electrode parameters including the electrode thickness and buffer layer thickness. 5-10(x10S0-6Tm) thick Au-ACPS electrodes were successfully fabricated by electroplating and ECR etcher. The improvement of modulation bandwidth can be theoretically observed from the combination of electrode and buffer layer thickness.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1968-1974
• /
• 1997

In this paper, the spectral domain approach is employed to investigate the characteristics of symmetrical and asymmetrical broadside-coupleed coplanar waveguides(BSC-CPW). These structures have large even(c)-odd(.pi.) mode-velocity ratio, suitable for wide-band and tight-coupling microwave circuit design. Efficient design parameters can be obtained from the effective dielectric constants and characteristic impedances calculated by varying the strip widths and slot widths in the BSC-CPW structure.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.41-48
• /
• 2005

We design and fabricate 3-dB tandem directional coupler using the coplanar waveguide structure which is applicable to balanced amplifiers and mixers for 60 GHz wireless local area network system. The coupler comprises the multiple-sectional parallel-coupled lines to facilitate the fabrication process, and enable smaller device size and higher directivity than those of the conventional 3-dB coupler employing the edge-coupled line. In this study, we adopt the structure of two-sectional parallel-coupled lines of which each single-coupled line has a coupling coefficient of -8.34 dB and airbridge structure to monolithically materialize the uniplanar coupler structure instead of using the conventional multilayer or bonded structure. The airbridge structure also supports to minimize the parasitic components and maintain desirable device performance in V-band (50$\~$75 GHz). The measured results from the fabricated couplers show couplings of 3.S$\~$4 dB and phase differences of 87.5$^{\circ}{\pm}1^{\circ}$ in V-band range and show directivities higher than 30 dB at a frequency of 60 GHz.