• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.43.1-43.1
• /
• 2011

The detail simulation modeling of fully-fed induction generator is investigated through PC based MATLAB/Simulink environment. Generator's stator currents are controlled by indirect vector control method. In this method, generator side converter controls the maximum excitation (air gap flux) by stator d-axis current and controls generator torque by stator q-axis current. Induction generator speed is controlled by tip speed ratio (TSR) upon the wind speed variations in order to generate the maximum output power. The generator torque model is specified as a 3-blade wind turbine with rating, then, the model is simulated under normal operating condition and three different fault conditions. The matlab model designed for fully-fed induction generator based wind farm provides good performance under normal and grid fault conditions. It provides good results for different pwm techniques and fault conditions except the single-phase line to ground fault, which should be verified with real time data from wind farms.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.457-462
• /
• 2014

This letter proposes a low-jitter DLL-based clock generator with two negative feedback loops. The main negative feedback loops suppress the jitter of DLL. The additional negative feedback loops suppress the delay-time variance of each delay stages. Both two negative feedback loops in a DLL results in suppressing the jitter of clock signal further. Measurement results of the DLL-based clock generator with two negative feedback loops fabricated in a one-poly six-metal $0.18{\mu}m$ CMOS process show 5.127-ps rms jitter and 47.6-ps peak-to-peak jitter at 1 GHz.

• 전력전자학회논문지
• /
• 제24권3호
• /
• pp.153-160
• /
• 2019

This study proposes a current source-type pulse generator to improve output voltage and current waveforms under a capacitively coupled plasma (CCP) system. The proposed circuit comprises two parallel-connected current source-type converters. These converters can satisfy the required output waveforms of plasma processing. The parallel-connected converters operate without reverse current fault by applying a time-delay control technique. Conventional voltage source converters based on pulse power supply exhibit drawbacks in short-circuit current, and problems occur when they are applied to a CCP system. The proposed pulse power supply based on a current source converter fundamentally solves the short-circuit current problem. Therefore, this topology can improve the voltage and current accuracy of a CCP system.

• Journal of Power Electronics
• /
• 제17권4호
• /
• pp.1004-1013
• /
• 2017

This paper presents an interleaving scheme for parallel-connected power systems to reduce the DC-link current ripple. A paralleled generator system generates current ripple by the Pulse Width Modulation (PWM) of each generator side converter. The current ripple in the DC-link degrades the efficiency of the whole generator system and decreases the lifetime of the DC-link capacitors. To mitigate these issues, the expression of the DC-link current is derived by a double-integral Fourier analysis while considering the modulation schemes. Optimized interleaving angles for the parallel generator system are obtained based on an analysis to minimize the dominant current harmonics component. Finally, the proposed interleaving scheme reduces the RMS value of the DC-link current ripple. Simulation and experimental results verify the effectiveness of the proposed interleaving scheme.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.639-643
• /
• 2003

We are interested in this paper on the control of an electromechanical system consisting of a doubly-fed induction generator(DFIG), driven by a prime mover that can supply or extract mechanical power, e.g., a flywheel inertia, and an induction motor(IM). The stator of the Induction machine is connected to the stator of the generator whose rotor voltage is regulated by a bidirectional converter. The main interest of this configuration is that it permits a bidirectional power flow between the motor, which may operate in regenerative mode, and the generator We propose a passivity-based controller to regulate the motor mechanical speed. Since this kind of controllers achieve stabilization via energy balancing, regulation of the power flow in the system is naturally incorporated. Simulation results are presented to illustrate the main points of our paper.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.81-90
• /
• 2008

This paper presents an investigation of a voltage and frequency controller for an isolated asynchronous generator (IAG) driven. by a wind turbine and supplying 3-phase 4-wire loads to the isolated areas where a grid is not accessible. The control strategy is based on the indirect current control of the VSC (voltage source converter) using the frequency PI controller. The proposed controller consists of three single-phase IGBT (Insulated Gate Bipolar Junction Transistor) based VSC, which are connected to each phase of the IAG through three single phase transformers and a battery at their DC link. The controller has the capability of controlling reactive and active powers to regulate the magnitude and frequency of the generated voltage, harmonic elimination, load balancing and neutral current compensation. The proposed isolated system is modeled and simulated in MATLAB using Simulink and PSB (Power System Block-set) toolboxes to verify the performance of the controller.

• Journal of Electrical Engineering and Technology
• /
• 제2권1호
• /
• pp.68-80
• /
• 2007

This paper covers switched reluctance generator (SRG) and its comparison with induction and synchronous machines for distributed generation. The SRG is simple in design, robust in construction, and fault tolerant in operation; it can also withstand very high temperatures. However, the performance and cost of the SRG power electronics driver are highly affected by the topology and design of the converter. IGBT and MOSFET based converters are not suitable for very high power applications. This paper presents thyristor-based resonant converters which are superior candidates for very high power applications. Operations of the converters are analyzed and their characteristics and dynamics are determined in terms of the system parameters. The resonant converters are capable of handling high currents and voltages; these converters are highly efficient and reliable as well. Therefore, they are suitable for high power applications in the range of 1MW or larger for distributed generation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.706-707
• /
• 2011

The insertion of the crowbar system in the doubly fed induction generator rotor circuit for a short period of time during grid disturbance enables a more efficient way of limiting transient rotor current and hence protecting the rotor side converter (RSC) and the DC - link capacitor. When crowbar is activated at fault occurrence and clearance time, RSC is blocked while DC -link capacitor and the grid side converter (GSC) can be controlled to provide reactive power support at the PCC and improve the voltage which helps to comply with grid codes. In this paper, control strategies for crowbar system to limit the rotor current during fault is presented with RSC and GSC controllers are modified to control PCC voltage during disturbance to enhance DFIG wind farm to comply with some strict grid codes. Model simulated on MATLAB/Simulink verify the study through simulation results presented.

• 한국정보통신학회논문지
• /
• 제21권7호
• /
• pp.1261-1266
• /
• 2017

지연 시간 전압 분산 변환기 (DVVC) 및 평균 회로 (AC)가 있는 지터 억제 지연 고정 루프 (DLL) 기반 클록 발생기를 제안하였다. 제안한 클록 발생기는 지연고정루프에서 무작위로 발생하는 지터와 회로의 구조에 의해 발생하는 지터를 억제하도록 하였다. 지연 시간 전압 분산 변환기는 각 지연단의 지연 차이를 감지하고 출력 전압을 생성한다. 평균회로는 두개의 연속되는 지연 시간 전압 분산 변환기의 출력 전압을 평균화 한다. 지연 시간 전압 분산 변환기 및 평균 회로는 연속적인 지연단의 지연 시간을 평균화하고 모든 지연단의 지연 시간을 동일하게 만든다. 또한 루프필터 출력 전압의 변동을 줄이기 위해 부궤환 기능으로 효과적인 작동을 하는 스위치가 있는 커패시터가 도입되었다. One-poly six-metal $0.18{\mu}m$ CMOS 공정으로 제작 된 DLL 기반 클록 발생기의 측정 결과는 13.4 ps rms 지터특성을 보여준다.

• 전기전자학회논문지
• /
• 제18권4호
• /
• pp.586-592
• /
• 2014

본 논문에서는 DT-CMOS(Dynamic Threshold voltage Complementary MOSFET) 스위칭 소자를 사용한 DC-DC Buck 컨버터를 제안하였다. 높은 효율을 얻기 위하여 PWM 제어방식을 사용하였으며, 낮은 온 저항을 갖는 DT-CMOS 스위치 소자를 설계하여 도통 손실을 감소시켰다. 제안한 Buck 컨버터는 밴드갭 기준 전압 회로, 삼각파 발생기, 오차 증폭기, 비교기, 보상 회로, PWM 제어 블록으로 구성되어 있다. 삼각파 발생기는 전원전압(3.3V)부터 접지까지 출력 진폭의 범위를 갖는 1.2MHz의 주파수를 생성하며, 비교기는 2단 증폭기로 설계되었다. 그리고 오차 증폭기는 70dB의 이득과 $64^{\circ}$의 위상여유를 갖도록 설계하였다. 또한 제안한 Buck 컨버터는 current-mode PWM 제어회로와 낮은 온 저항을 갖는 스위치를 사용하여 100mA의 출력 전류에서 최대 95%의 효율을 구현하였으며, 1mA 이하의 대기모드에도 높은 효율을 구현하기 위하여 LDO 레귤레이터를 설계하였으며, 또한 2개의 IC 보호 회로를 내장하여 신뢰성을 확보하였다.