• ETRI Journal
• /
• v.28 no.4
• /
• pp.533-536
• /
• 2006

A distributed Bragg reflector (DBR) laser and a high speed electroabsorption modulator (EAM) are integrated on the basis of the selective area growth technique. The typical threshold current is 4 to 6 mA, and the side mode suppression ratio is over 40 dB with single mode operation at 1550 nm. The DBR laser exhibits 2.5 to 3.3 mW fiber output power at a laser gain current of 100 mA, and a modulator bias voltage of 0 V. The 3 dB bandwidth is 13 GHz. A 10 Gbps non-return to zero operation with 12 dB extinction ratio is obtained. A four-channel laser array with 100 GHz wavelength spacing was fabricated and its operation at the designed wavelength was confirmed.

• Current Photovoltaic Research
• /
• v.3 no.3
• /
• pp.75-79
• /
• 2015

Recently, $Cu_2ZnSn(S_xSe_{1-x})_4$ (CZTSSe) has been received a tremendous attraction as light absorber material in thin film solar cells (TFSCs), because of its earth abundance, inexpensive and non-toxic constituents and versatile material characteristics. Kesterite CZTSSe thin films were synthesized by sulfo-selenization of sputtered Cu/Sn/Zn stacked metallic precursors. The sulfo-selenization of Cu/Sn/Zn stacked metallic precursor thin films has been carried out in a graphite box using rapid thermal annealing (RTA) technique. Annealing process was done under sulfur and selenium vapor pressure using Ar gas at $520^{\circ}C$ for 10 min. The effect of tuning Se/(S+Se) precursor composition ratio on the properties of CZTSSe films has been investigated. The XRD, Raman, FE-SEM and XRF results indicate that the properties of sulfo-selenized CZTSSe thin films strongly depends on the Se/(S+Se) composition ratio. In particular, the CZTSSe TFSCs with Se/(S+Se) = 0.37 exhibits the best power conversion efficiency of 4.83% with $V_{oc}$ of 467 mV, $J_{sc}$ of $18.962mA/cm^2$ and FF of 54%. The systematic changes observed with increasing Se/(S+Se) ratio have been discussed in detail.

• Journal of Environmental Science International
• /
• v.30 no.9
• /
• pp.709-717
• /
• 2021

This study evaluated the growth, physiological responses and productivity based on the intercropping ratio of cherry tomato (Lycopersicon esculentum L.) with basil (Ocimum basilicum L.). on the rooftops to determine out the efficient ratio in urban agriculture. From April to September 2019, an experiment was conducted on the rooftop of Konkuk University Glocal Campus. Cherry tomato and basil were selected as companion plants for eco-friendly urban agriculture on the rooftops. Each plot was created with a width of 100 cm, length of 100 cm, and height of 25 cm. After installing drainage and waterproof layers from bottom to top, substrate was laid out with a height of 20 cm. Intercropping ratio was consisted of a single tomato plant (TC), 2:1 tomato to basil (T₂B₁), 1:1 tomato to basil (T₁B₁), 1:2 tomato to basil 2 (T₁B₂), and a single basil plant (BC), were conducted using a randomized complete plot design with five treatments and three replication (a total 15 plots). Measurements were divided into growth, physiological responses, and productivity parameters, and detailed items were investigated and analyzed by classifying them into plant height, leaf length, leaf width, number of leaves, root length, root collar caliper, chlorophyll contents, fresh weight, dry weight, number of fruit, fruit caliper, fruit weight, and sugar content. Comparative analyses of cherry tomato with basil plants by intercropping ratio, growth, physiological, and productivity responses are determined to be efficient when the ratio of cherry tomato to basil ratio is 2:1 or 1:1.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.4
• /
• pp.269-276
• /
• 2006

Strength Design method for involute spur gears is developed. The developed gear strength design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is matrix form which is developed from this study. Design variables are transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress, etc. Gear design method developed this study can be apply to the gears of plants, machine tools, automobiles.

• Journal of the Korean Society of Industry Convergence
• /
• v.10 no.4
• /
• pp.255-262
• /
• 2007

The main purpose of this study is to figure out of seismic structural behaviour of Gukrakjeon of Bongjung-Temple which is the oldest wooden architecture in Korea, and to evaluate in engineering aspect of seismic records. The non-lineal analysis is essential for accurate evaluation of wooden architecture in seismic behaviour. Based on the experimental test with applying cycle forces in joint specimens is focusing on not only to prove the structural characteristics, but also to evaluate damping ratio, As the result of this test, damping ratio is affected not the joint methods but the frame variations. The average damping ratio was 26%.

• ETRI Journal
• /
• v.29 no.6
• /
• pp.811-813
• /
• 2007

We report on a ridge waveguide laser diode with laterally tapered waveguides fabricated in a single growing step using a double patterning method. In this structure, nearly constant output power is obtained with the change of the lower tapered waveguide width, and the facet power ratio of 1.4 to 1.5 is observed over the current range. The asymmetric facet power property is also investigated.

• Journal of Digital Convergence
• /
• v.14 no.10
• /
• pp.375-380
• /
• 2016

This study aimed to evaluate the possibility for assessment of binocular visual function about alteration for near point of convergence (NPC). Study subjects were total 30 (emmetropia 16, myopia 14), who had no eye disease except for the phoria and monocular corrected vision 1.0 and over. Near point of accommodation (NPA), NPC and phoria test were measured both at ordinary and stimulation of +1D. Ordinary NPC was 1.77cm shorter than NPC stimulated +1D and the NPC of emmetropia was shorter than that of myopia. The difference between NPC stimulated +1D and ordinary were increased in the emmetropia. As the NPC increased, the AC/A ratio was elevated and the feature of near exophoria appeared. The results suggested that the alteration of NPC might substitute AC/A ratio for reference variable of binocular vision. If converged and analyzed comparatively with another binocular visual evaluation test, the alteration of NPC could be developed for substitution of evaluation test.

• Current Photovoltaic Research
• /
• v.2 no.4
• /
• pp.177-181
• /
• 2014

$Cu_2ZnSn(S_xSe_{1-x})_4$ (CZTSSe) absorber thin films were prepared on Mo coated soda lime glass substrates by sulfo-selenization of sputtered stacked Zn-Sn-Cu precursor thin films. The Zn-Sn-Cu precursor thin films were sulfo-selenized inside a graphite box containing S and Se powder using rapid thermal processing furnace at $540^{\circ}C$ in Ar atmosphere with pre-treatment at $300^{\circ}C$. The effect of different S/Se ratio on the structural, compositional, morphological and electrical properties of the CZTSSe thin films were studied using XRD (X-ray diffraction), XRF (X-ray fluorescence analysis), FE-SEM (field-emission scanning electron microscopy), respectively. The XRD, FE-SEM, XRF results indicated that the properties of sulfo-selenized CZTSSe thin films were strongly related to the S/Se composition ratio. In particular, the CZTS thin film solar cells with S/(S+Se)=0.25 shows best conversion efficiency of 4.6% ($V_{oc}$ : 348 mV, $J_{sc}$ : $26.71mA/cm^2$, FF : 50%, and active area : $0.31cm^2$). Further detailed analysis and discussion for effect of S/Se composition ratio on the properties CZTSSe thin films will be discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.12
• /
• pp.822-827
• /
• 2017

Mg/Al layered double hydroxide with two-dimensional (2D) nanostructures was synthesized by a hydrothermal technique. The morphology and aspect ratio of $Mg_4Al_2(OH)_{14}3H_2O$ were controlled by the concentration and kinds of the hydrolysis agent, and temperature. The aspect ratio of $Mg_4Al_2(OH)_{14}3H_2O$ layered double hydroxides with the 2D hexagonal crystal structure was tailored from about 12.6 to about 45.7. The intercalated $CO{_3}^{2-}$ anions of the synthesized 2D $Mg_4Al_2(OH)_{14}3H_2O$ layered double hydroxides were exchanged to $NO_3{^-}$ anions. The bulk 2D $Mg_4Al_2(OH)_{14}3H_2O$ layered double hydroxides with the increased space between two layers due to the anion exchange were exfoliated in a formamide solution. The aspect ratio of the exfoliated 2D $Mg_4Al_2(OH)_{14}3H_2O$ layered double hydroxides increased to 570.3.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.1
• /
• pp.19-23
• /
• 2018

In a Pb-included piezoelectric composition, $Sr_yPb_{1-y}[(Zn_{1/3}Nb_{2/3})_x-(Ni_{1/3}Nb_{2/3})_{0.2}-(Zr_{0.46}Ti_{0.54})_{0.8-x}]O_3$ was selected in order to attain high piezoelectric properties. According to the PZN ratio (x) and the amount of Sr doping (y), the crystal structure, microstructure and piezoelectric properties were measured and evaluated. In the case of Sr 4 mol% doping, the piezoelectric properties were the highest for a PZN ratio of 0.1. In this condition, the grain size was larger and the intensity was higher. With the PZN ratio fixed and varying the Sr doping, the piezoelectric properties increased until 10 mol% doping and then decreased for over 12 mol% doping. In the case of x＝0.1 and y＝10 mol%, the best piezoelectric properties were obtained, i.e., $d_{33}=660pC/N$ and $k_p=68.5%$, and these values seem to be related to the grain size and crystal structure.