• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.678-686
• /
• 2014

A novel auxiliary resonant commutated pole (ARCP) link for three-phase PWM voltage-fed converter is presented. The ARCP link consists of two auxiliary switches, one resonant inductance, and six diodes, which is simpler than the conventional ARCP designs. Based on the phase and amplitude control, the proposed converter can take a minimum switching times PWM method, which results in reduced losses and a simplified control. In addition, the zero-voltage resonance modes are analyzed. Finally, simulation and experimental results show that the system can realize zero-voltage switching with a unity power factor.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.560-568
• /
• 2019

This paper studies the inherent relationship between currents and zero-sequence components. Then a precise algorithm is proposed to calculate the injected zero-sequence component to control the DC-Link neutral-point voltage balance, which can result in a more efficient and flexible neutral point voltage balance with a desirable performance. In addition, it is shown that carried-based PWM with the calculated zero-sequence component scheme can be equivalent to space-vector pulse-width modulation (SVPWM). Based on the proposed method, the optimal zero-sequence component of the feasible modulation indices is analyzed. In addition, the unbalanced load limitation of the DC-Link neutral-point voltage balance control is also revealed. Simulation and experimental results are shown to verify the validity and practicality of the proposed algorithm.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.8-13
• /
• 1998

A tracking controller is presented for RLFJ(rigid link flexible joint) robot manipulators with only position measurements. The controller is developed based on the integrator backstepping design method and on the two observers: the first is simple linear form observer for the filtered link velocity errors and the other for the actuator velocities. The proposed controller achieves exponential tracking of link positions and velocities while keeping all internal signals bounded. It also guarantees exponential convergence of the estimated signals to their actual ones. Finally, simulation results are included to demonstrate the tracking performance.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1587-1599
• /
• 2017

This paper proposes a real-time implementation of an optimal operation of a double stage grid connected wind power system incorporating an active power filter (APF). The system is used to supply the nonlinear loads with harmonics and reactive power compensation. On the generator side, a new adaptive neuro fuzzy inference system (ANFIS) based maximum power point tracking (MPPT) control is proposed to track the maximum wind power point regardless of wind speed fluctuations. Whereas on the grid side, a modified predictive current control (PCC) algorithm is used to control the APF, and allow to ensure both compensating harmonic currents and injecting the generated power into the grid. Also a type 2 fuzzy logic controller is used to control the DC-link capacitor in order to improve the dynamic response of the APF, and to ensure a well-smoothed DC-Link capacitor voltage. The gained benefits from these proposed control algorithms are the main contribution in this work. The proposed control scheme is implemented on a small-scale wind energy conversion system (WECS) controlled by a dSPACE 1104 card. Experimental results show that the proposed T2FLC maintains the DC-Link capacitor voltage within the limit for injecting the power into the grid. In addition, the PCC of the APF guarantees a flexible settlement of real power exchanges from the WECS to the grid with a high power factor operation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4A
• /
• pp.451-463
• /
• 2000

In this paper, we design the radio data link protocols with QoS provisioning for mobile multimedia such as voice, data, and video in CDMA-based ATM networks, and analyze the performance of the data link protocols. To support mobile multimedia traffic, the required QoS parameters and the characteristics are analyzed, and wireless protocol stacks are proposed for integrating the wireless access network and ATM transport networks, and radio data link protocols are designed for provisioning QoS Control. The data link protocols are analyzed assuming that the system is supporting voice and data traffic simultaneously. In case of data traffic, the delay and throughput of SREJ ARQ and Type-1 Hybrid ARQ scheme are compared, and in case of voice traffic, the packet loss rate of BCH coding is analyzed according to the varying data traffic loads. The results indicate that the adaptive radio link protocols are efficient to support QoS requirements while the complexities are increased.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.8A
• /
• pp.868-878
• /
• 2004

In this paper, we analyse feasibility of Zone-based Power Control (ZPC) scheme introduced for CDMA forward link(1) in the reverse link. To operate ZPC scheme in the CDMA systems the maximum power level that can be allocated to each traffic channel should be determined. Because all the service channels share the whole power resource in the forward lint a specific mechanism that determines Maximum power resource to each traffic channel is required to operate ZPC scheme in the forward link. However, ZPC scheme can be easily adopted to the reverse link, because of the fact that the whole power resource of service terminal is only confined to its traffic channel. In other words, we need not to determine the maximum power resource to be allocated in the reverse traffic channel. Simulation results show that ZPC scheme adopted to the reverse link yields a significant performance improvement compared with the conventional TPC(IS-95 TPC) scheme in terms of the power consumption and the traffic capacity of Portables, especially with the increasing number of high-rate data traffics. With the proposed scheme, not only be extended the service coverage of high-rate data traffic to the entire cell service coverage, but also the QoS of low-rate traffic can keep going through the service time, especially, in the situation that the incoming interference is much larger.

• Journal of Communications and Networks
• /
• v.11 no.1
• /
• pp.84-93
• /
• 2009

This paper focuses on message complexity performance analysis of mobile ad hoc network (MANET) address autoconfiguration protocols (AAPs) in reference to link errors generated by mobile wireless nodes. An enhancement was made using a proposed retransmission limit, S, to be computed for error recovery (based on the link error probability), to measure message complexity of AAPs in reference to the link error probability, $P_e$. The control procedures for the retransmission limit have been included for each of the AAPs. Retransmission limit control is critical for efficient energy consumption of MANET nodes operating on limited portable energy. O-notation has been applied to analyze the upper bound of the number of messages generated by a MANET group of nodes. The AAPs investigated in this paper are strong duplicate address detection (DAD), weak DAD with proactive routing protocol (WDP), weak DAD with on-demand routing protocol (WDO), and MANETConf. Each AAP reacts different to link errors, as each AAP has different operational procedures. The required number of broadcasting, unicasting, relaying, and received messages of the nodes participating in a single-node joining procedure is investigated to asymptotically calculate the message complexity of each AAP. Computer simulation was conducted and the results have been analyzed to verify the theoretical message complexity bounds derived. The message complexity of WDP was lowest, closely followed byWDO, based on the simulation results and analysis of the message complexity under nominal situations. The message complexity of MANETConf was higher than WDO, and strong DAD resulted to be most complex among the four AAPs.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.5
• /
• pp.861-868
• /
• 2010

As CAS, X-ATK, and INT models considered as the most typical Air-to-Ground operation models in ROKAF are mainly designed as the voice-centered system between aircraft and ground control facilities, it is critical to newly develop the Link-16 based model for the ROK-US combined operation between F-15K, AWACS, M-SAM, and KDX-III equipped with Link-16. Former studies had been limited to the CAS operation, and they had mainly focused on reducing the voice transmission time to exchange the information between each mission step with maintaining existing operation steps. Therefore, this paper makes up the weak point in former studies, thereby designing new Air-to-Ground operation model for CAS, X-ATK, INT mission using Enterprise Architecture OV6c, which enables both aircraft and ground control facilities or between aircraft to obtain the real-time information on the location, identification, armament and the real-time image data through the broadcasting function. Based on the analysis of new operation model, we come to a conclusion that by simultaneously exchanging the information on mission between nodes concerned through the broadcasting function of Link-16. It is possible to cut down superfluous steps among the mission steps, and to reduce the mission time. It is clear that it gives rise to improve the battle efficiency and the decision-making tempo as well as the battlefield situational awareness.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.1
• /
• pp.66-72
• /
• 2000

As the demand for the design of modular manipulators or special purpose manipulators has increased, task based design to design an optimal manipulator for a given task become more and more important. However, the complexity with a large number of design parameters, and highly nonlinear and implicit functions are characteristics of a general manipulator design. To achieve the goal of task based design, it is necessary to develop a methodology to solve the complexity. This paper addresses how to determine the kinematic parameters of a two-degrees of freedom manipulator with parallelogram five-bar link mechanism from a given task, namely, how to map a given task into the kinematic parameters. With simplified example of designing a manipulator with five-bar link mechanism, the methodology for task based design is presented. And it introduces formulations of a given task and manipulator specifications, and presents a new dexterity measure for manipulator design. Also the optimization problem with constraints is solved by using a genetic algorithm that provides robust search in complex spaces.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.6
• /
• pp.603-608
• /
• 2007

In the conventional AOA(angle-of-arrival) positioning utilizing reverse-link wireless channel, each sensor should be equipped with an array antenna to measure the incident angle of signal transmitting from a tag. To perform the complicated signal processing for angle measurements, sensor size and its power consumption will be large. In some applications like mobile robot location, there exists no strict restriction in tag size or in power consumption. Rather, it is desirable that the sensor would be as small as possible. This paper presents a new AOA positioning method utilizing forward-link channel. Under the assumption that the mobile robot is operating on the flat surface, the measurement model for FLAOA(tiJrward-link AOA) is derived first. Two kinds of position estimation algorithms using FLAOA measurements are proposed; Gauss-Newton method and closed-fonn solution method. With the proposed methods, we can ohtain the attitude of robot as well as its position. Positioning performance of proposed methods is compared by computer simulation. Simulation results show that the closed-form solution method using FLAOA measurements is suitable for indoor robot positioning.