• ETRI Journal
• /
• v.46 no.4
• /
• pp.708-715
• /
• 2024

We propose a 10-GHz 2 × 2 phased-array radio frequency (RF) receiver with an 8-bit linear phase and 15-dB gain control range using 65-nm complementary metal-oxide-semiconductor technology. An 8 × 8 phased-array receiver module is implemented using 16 2 × 2 RF phased-array integrated circuits. The receiver chip has four single-to-differential low-noise amplifier and gain-controlled phase-shifter (GCPS) channels, four channel combiners, and a 50-Ω driver. Using a novel complementary bias technique in a phase-shifting core circuit and an equivalent resistance-controlled resistor-inductor-capacitor load, the GCPS based on vector-sum structure increases the phase resolution with weighting-factor controllability, enabling the vector-sum phase-shifting circuit to require a low current and small area due to its small 1.2-V supply. The 2 × 2 phased-array RF receiver chip has a power gain of 21 dB per channel and a 5.7-dB maximum single-channel noise-figure gain. The chip shows 8-bit phase states with a 2.39° root mean-square (RMS) phase error and a 0.4-dB RMS gain error with a 15-dB gain control range for a 2.5° RMS phase error over the 10 to10.5-GHz band.

• ETRI Journal
• /
• v.26 no.5
• /
• pp.501-504
• /
• 2004

This paper presents a simple gain/phase blind compensation algorithm with an automatic gain control (AGC) function for the adoption of the AGC function and compensation for gain/phase imbalances in quadrature phase shift keying (QPSK) direct conversion receivers (DCRs). The AGC function is interactively operated with the compensation algorithm for gain/phase imbalances. By detecting the gain sum and difference values between the I-channel and Q-channel, the combined AGC and gain imbalance compensation algorithm provides a simpler DCR architecture.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.4
• /
• pp.39-44
• /
• 2008

In this paper, through the study of discrete implementation of time delay control (TDC) and PID control algorithm, a new systematic gain selection method for PID controller is proposed. An important advantage of this method is that it may be applied to real systems with very simple and systematic procedure. The proposed method is derived for SISO systems and then extended to MIMO system. Through simulation for the second order non-linear plant and experiment on 2-DOF robot, the effectiveness of the proposed method is confirmed. The proposed method could solve the problem of difficulty in gain tuning of existing PID controller.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.1
• /
• pp.32-39
• /
• 1997

One of the most important performance criteria in tuning the gain of position loop controller for CNC machining center is the contour error. In this papre we analyze contour error in the linear and circular interpolations for the axis-matched and mismatched cases. To have small contour errors, it is necessary to set the P gain for each axis to be same. And the D gain should be much smaller than the P gain. Baded on the analysis in the frequency domain, we propose a gain tuning method for the P and PD controllers. We show that the PD controller is better than the P controller. The effectiveness of this method is demonstrated by experiments.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.240-243
• /
• 2001

This paper presents the digital controller using variable gain for single-phase power factor correction (PFC) converter. Generally, the gain of inner current control loop in single-stage PFC converter has a constant magnitude. This is why input current is distorted under low input voltage. In particular, a digital controller has more time delay than an analog controller which degrades characteristics of control loop. So, it causes the problem that the gain of current control loop isn't increased enough. In addition, the oscillation happens in the peak value of the input voltage open loop PFC system gain changes according to ac input voltage. These aspects make the design of the digital PFC controller difficult. In this paper, the improved digital control method for single-phase power factor converter is presented. The variable gain according to input voltage and input current help to improve current shape. The 800W converter is manufactured to verify the proposed control method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.363-369
• /
• 2004

We propose, for the first time to our knowledge, a novel gain-clamping method for EDFA in WDM add/drop networks by introducing a disturbance observer technique. The control input signal for gain-clamping is composed of a nominal control signal and an additional control signal of compensating the gain fluctuations caused by channel add/drops. Based on disturbance observer technique, we designed the additional control signal such that it has the compensating information of estimated disturbance resulted from channel add/drops. The circuit for generating additional control signal can easily be implemented by using simple electronic devices. We proved the superiority of the new technique over the previous ones by showing simulation results of minimized dips and spikes that appear in power profile of EDFA in the process of channel add/drops.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.614-616
• /
• 2004

It is waste of time in industrial plant that the PI controller gain tuning. The PI controller has many trial-and-error steps for gain design. This paper proposes the optimum gain design of PI controller using a speed estimation in sensorless vector-control. In this method, a degree of stability and Hurwitz theory are applied and the controller gain is expressed by system parameters.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.336-343
• /
• 2011

This paper introduces a simple variable gain amplifier (VGA) structure that shows an inherently dB-linear gain control property. Requiring no additional components for dB-linear control, the structure is compact and power efficient. The designed two-stage VGA shows a gain control range of 60dB with the gain error in the range of ${\pm}0.4$ dB. The power consumption including the output buffer is 20.4 mW from 1.2 V supply voltage with bandwidth of 630 MHz. The prototype was fabricated in a 0.13 ${\mu}m$ CMOS process and the VGA core occupies 0.06 $mm^2$.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.12
• /
• pp.569-575
• /
• 2005

This paper proposes a gain scheduled control technique using time-delay for the nonlinear system with plant uncertainties and unexpected disturbances. The time delay-based gain scheduled control depends on a direct estimation of a function representing the effect of uncertainties. The information from the estimation is used to cancel the unknown dynamics and the unexpected disturbances simultaneously. The proposed estimation scheme with a finite convergence time is formulated in order to estimate the unknown scheduling variable variation. In other words, the time delay-based gain scheduled control uses the past observation of the system's response and the control input to directly modify the control actions rather than to adjust the controller gains or to identify system parameters. It has a simple structure so as to minimize the computational burden. The benefits of this proposed scheme are demonstrated in the simulation of an electromagnetic suspension system with plant uncertainties and external disturbances, and the proposed controller is compared with the conventional state feedback controller.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.4
• /
• pp.66-72
• /
• 2003

This paper proposes an optimum, problematic design for structural and control systems, taking a 3-D truss structure as an example. The structure is subjected to initial static loads and time-varying disturbances. The structure is controlled by a state feedback H$_{\infty}$ controller which suppress the effects of disturbances. The design variables are the cross sectional areas of truss members. The structural objective function is the structural weight. For the control objective, we consider two types of performance indices, The first function represents the effect of the initial loads. The second function is the norm of the feedback gain, These objective functions are in conflict with each other but are transformed into one control objective by the weighting method. The structural objectives is treated as the constraint, By introducing the second control objective which considers the magnitude of the feedback gain, we can create a design to model errors.