• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국ITS학회 논문지
• /
• 제10권6호
• /
• pp.74-83
• /
• 2011

하이패스 교통정보시스템은 프로브 차량을 이용하여 직접 구간정보를 수집함으로써, 보다 신뢰성 높은 정보를 운전자에게 제공할 수 있다. 그러나 프로브 차량의 운행상황과 특성, 그리고 통계처리 방법 등이 정보의 신뢰성에 영향을 미치며 특히, 도시부도로에서는 구간통행시간이 신호 지체시간 경험 유무에 의해 크게 영향을 받기 때문에, 수집되는 개별 프로브 데이터 간 많은 편차가 발생하게 된다. 따라서 구간정보의 신뢰도 제고를 위한 다각적인 방면에서의 연구가 필요하다. 그러나 하이패스 정보제공과 관련한 선행연구는, 주로 연속류 특성을 가지는 고속도로 구간을 대상으로 이루어져, 이를 단속류 교통 특성을 가지는 도시부도로에 적용시키기에 한계가 있었다. 따라서 본 연구에서는 도시부도로에서의 하이패스 교통자료 특성을 분석하고 적절한 가공방안을 마련하는데 의의를 두고자 하였다. 시공간도를 이용하여 RSE로부터 수집하는 도시부도로의 하이패스 자료 특성을 분석한 결과, 수집자료는 종료노드의 신호주기를 주기로 하여 도착 차량의 신호 대기 등에 따라 일정한 패턴을 나타내는 것을 알 수 있었다. 또한, 신호대기 횟수와 대기시간에 따라 수집데이터의 편차가 발생하는데, 혼잡 상황보다 비혼잡 상황에서 편차가 크게 나타났다. 이는 혼잡상황에서는 신호대기 횟수가 많아지면서, 편차가 일정부분 상쇄되기 때문인 것으로 분석되었다. 이러한 도시부도로의 하이패스 수집자료는 신호대기에 의한 교통특성을 반영하기 위해 평균값을 대표값으로 사용하는 것이 적절하며, 신호 및 도로 특성에 따라 지정체 판단기준을 조절할 필요가 있는 것으로 분석되었다. 본 연구에서 도출한 결과가 도시부도로에서의 하이패스 정보의 신뢰성을 향상 시킬 수 있는 초석이 되길 기대한다.

• Journal of Oral Medicine and Pain
• /
• 제32권2호
• /
• pp.157-175
• /
• 2007

본 연구는 농촌지역 주민들의 구취실태를 파악하고 구취에 관련된 요인을 알아봄으로써 구취예방 및 효율적인 구취제거 방안을 마련하는데 기초 자료를 제공하고자 일부 농촌지역의 주민 293명을 대상으로 2006년 1월 4일부터 1월 21일까지 면접설문조사(구강위생관리 행태, 구취관련 질병력, 구취실태), 구취측정, 구강검사, 치아우식활성검사(스나이더검사, 타액분비율검사, 타액완충능검사)를 실시한 결과 다음과 같은 결론을 얻었다. 1. 잇솔질 횟수는 1일 2회가 46.1 %로 가장 많았고, 여자가 남자보다 잇솔질 횟수가 많았다. 매일 혀솔질을 하는 군은 25.6%이었고, 보조 구강위생용품을 사용하는 군은 9.2 %이었다. 2. 평상시 구취를 자각하고 있는 사람은 62.5 %이었고, 구취를 가장 심하게 자각하는 시기는 기상 후가 72.7 %, 구취를 자각하는 부위는 잇몸에서 23.0 %, 구취의 유형으로는 구린 냄새가 37.2 %로 높게 나타났다. 3. 구취측정 결과 OG는 50 ppm미만이 54.3 %, $50{\sim}100ppm$ 범위에 41.6 %로 나타났고, $NH_3$는 $20{\sim}60ppm$ 범위에 52.6 %로 가장 높았다. 4. 구취관련 질병력별 OG는 치아우식증으로 인한 식편압입, 당뇨병과 구취에 대한 가족력군에서 $50{\sim}100ppm$ 범위에 유의하게 높았으며, $NH_3$는 호흡기계 질환군에서 유의한 차이가 있었다. 5 평상시 구취 자각정도별 OG는 '냄새가 나지 않는다'는 군과 '가끔 냄새가 난다'는 군에서 50 ppm 미만에 각각 55.9 %, 57.5 %로 나타났고, '본인이 느낄 정도로 항상 냄새가 난다'는 군과 '항상 심하게 냄새가 난다'는 군에서 $50{\sim}100ppm$ 범위에 각각 52.0 %, 63.6 %로 높게 나타났으며, $NH_3$는 모두 $20{\sim}60ppm$ 범위에 높게 나타났다. 6. 구강검사별 OG는 치수노출치와 식편압입이 많을수록, 설태지수가 높아질수록 $50{\sim}100ppm$ 범위에 OG값이 증가되었고, $NH_3$는 보철치가 많을수록, 설태지수가 높아질수록 유의하게 증가되었으며, 하악 국소의치군에서 60 ppm 이상으로 유의하게 증가되었다. 7. 스나이더검사는 고도활성이 43.0 %로 가장 높았고, 산 생성균의 활성이 높을수록 OG값이 증가되었다. 자극성 타액분비율 검사는 8.0 ml 이하에서 62.5 %로 가장 높았고, 타액분비율이 많을수록 OG값이 감소된 분포를 보였으며, 타액완충능검사는 0.1N 유산용액의 방울 수가 $6{\sim}10$ 방울에서 58.7 %로 가장 높았고, 타액완충능이 증가될수록 OG값이 냄새를 느끼지 못하는 50 ppm 미만에서 증가되었다. 8. 구강환경과 구취와의 상관관계에서 OG는 타액분비율, 보철치와 음의 상관관계를, 치수노출치, 충전치, 현존치, 설태량, 식편압입과 양의 상관관계를 보였으며, $NH_3$는 우식치와 음의 상관관계를, 보철치, 잇솔질 횟수와 양의 상관관계를 보였다. 9. 다중회귀분석 결과에서 OG에 영향을 주는 요인으로는 여자, 치수노출치, 보철치, 식편압입, 타액분비율, 설태지수, 스나이 더검사의 고도활성이 선정되었고 이들의 설명력은 45.1 %이었으며, NH3에 영향을 주는 요인으로는 여자, 치수노출치, 설태지수, 보철치가 선정되었으며 이들의 설명력은 6.6 %이었다. 이상의 결과를 볼 때, 조사대상 농촌지역 주민들의 구취실태는 구강환경 및 구취관련 요인, 치아우식활성검사의 스나이더 검사, 타액분비율검사와 밀접한 관련이 있음을 시사한다. 따라서 이들 주민들의 구취예방을 위해서는 식후에 올바른 잇솔질 방법 및 혀솔질과 더불어 보조 구강위생용품을 사용하여 식편압입과 설태제거를 해야 할 필요성이 강조된다. 구취의 원인과 그 성분은 매우 복잡하고 다양하므로 개인별 구취발생 요인을 정확하게 분석하기 위해서는 추후 계속적이고, 체계적인 연구가 필요하며, 보건(지)소의 치과위생사를 활용하여 지역사회 주민들에게 계속적인 구강보건교육 프로그램이 제공되어야 한다고 생각된다.

• 조형예술학연구
• /
• 제10권
• /
• pp.183-218
• /
• 2006

Colors change in time corresponding with the value system and aesthetic consciousness of the time. The roles that colors play in painting can be divided into the formative role based on the contrast and harmony of color planes and the aesthetic role expressed by colors to represent the objects. The aesthetic consciousness of the orient starts with the Civility(禮) and Pleasure(樂), which is closely related with restrained or tempered human feelings. In the art world of the orient including poem, painting, and music, what are seen and felt from the objects are not represented in all. Added by the sentiment laid background, the beauty of the orient emphasizes the beauty of restraint and temperance, which has long been the essential aesthetic emotion of the orient. From the very inception of oriental painting, colors had become a symbolic system in which the five colors associated with the philosophy of Yin and Yang and Five Forces were symbolically connected with the four sacred animals of Red Peacock, Black Turtle, Blue Dragon, and White Tiger. In this color system the use of colors was not free from ideological matters, and was further constrained by the limited color production and distribution. Therefore, development in color expression seemed to have been very much limited because of the unavailability and unreadiness of various colors. Studies into the flow in oriental painting show that color expression in oriental painting have changed from symbolic color expression to poetic expression, and then to emotional color expression as the mode of painting changes in time. As oriental painting transformed from the art of religious or ceremonial purpose to one of appreciation, the mast visible change in color expression is the one of realism(simulation). Rooted on the naturalistic color expression of the orient where the fundamental properties of objects were considered mast critical, this realistic color expression depicts the genuine color properties that the objects posses, with many examples in the Flower & Bird Painting prior to the North Sung dynasty. This realistic expression of colors changed as poetic sentiments were fused with painting in later years of the North Sung dynasty, in which a conversion to light ink and light coloring in the use of ink and colors was witnessed, and subjective emotion was intervened and represented. This mode of color expression had established as free and creative coloring with vivid expression of individuality. The fusion of coloring and lyricism was borrowed from the trend in painting after the North Sung dynasty which was mentioned earlier, and from the trend in which painting was fused with poetic sentiments to express the emotion of artists, accompanied with such features as light coloring and compositional change. Here, the lyricism refers to the artist's subjective perspective of the world and expression of it in refined words with certain rhythm, the essence of which is the integration of the artist's ego and the world. The poetic ego projects the emotion and sentiment toward the external objects or assimilates them in order to express the emotion and sentiment of one's own ego in depth and most efficiently. This is closely related with the rationale behind the long-standing tradition of continuous representation of same objects in oriental painting from ancient times to contemporary days. According to the thoughts of the orient, nature was not just an object of expression, but recognized as a personified body, to which the artist projects his or her emotions. The result is the rebirth of meaning in painting, completely different from what the same objects previously represented. This process helps achieve the integration and unity between the objects and the ego. Therefore, this paper discussed the lyrical expression of colors in the works of the author, drawing upon the poetic expression method reflected in the traditional Flower and Bird Painting, one of the painting modes mainly depending on color expression. Based on the related discussion and analysis, it was possible to identify the deep thoughts and the distinctive expression methods of the orient and to address the significance to prioritize the issue of transmission and development of these precious traditions, which will constitute the main identity of the author's future work.

• Korean Chemical Engineering Research
• /
• 제45권6호
• /
• pp.638-647
• /
• 2007

본 연구에서는 회수증진기법 중 하나인 $CO_2$ 공법을 생산유전에 적용할 경우, 적용성 여부를 간단하고 정량적으로 평가할 수 있도록 하기 위한 평가차트를 개발하였다. 이 평가차트는 소스의 이용성, $CO_2$-오일의 혼합도, 저류층 및 오일 특성의 적정성, 주입기법의 평가항목으로 구성되어 있다. 저류층 및 오일의 특성에서 오일 비중, 오일 점성도, 오일 포화도, 저류층 온도 및 투과도의 기본평가항목에 대해서는 점수로 평가되며, $CO_2$ 순도, 저류층 두께 및 경사도 등의 추가평가항목에 대해서는 상 중 하로 구분하여 정량적으로 평가된다. 또한 미서블공법의 주입기법 평가에서는 지층경사, 수직투과성 및 저류층 두께 등에 따라 연속주입공법과 WAG($CO_2$) 공법의 여부가 정성적으로 평가된다. 이와 같이 구성된 평가차트에 대해 $CO_2$ 공법이 성공적으로 수행된 51개 유전의 적용사례를 분석하여 이를 토대로 $CO_2$ 공법이 가능한 추천점수를 설정하였다. 본 연구에서 개발한 평가차트를 국내 기업이 참여중인 스코틀랜드의 캡틴 생산유전과 베네수엘라의 오나도 생산유전에 적용하여 $CO_2$ 공법의 적용 가능성 여부를 평가하였다. 여기서 캡틴 유전은 저류층의 공극률과 투과도가 매우 양호하나, $C_{21+}$ 이상의 무거운 탄화수소 함유량이 54%를 넘는 중질유이다. 따라서 이러한 중질오일은 $CO_2$와 비미서블공법으로 진행되므로 비미서블공법 기준하의 기본평가항목에 대해서만 평가한 결과 비미서블 $CO_2$ 공법이 적정한 것으로 평가되었다. 한편, 베네수엘라의 오나도 유전에 대해서는 최소 미서블압력이 저류층 압력보다 낮게 산출되어 미서블 $CO_2$ 공법이 적용 가능할 것으로 평가되었다.

• 대한간호학회지
• /
• 제4권1호
• /
• pp.1-21
• /
• 1974

A considerable change of the Korean nursing system has been made during the last decade not only in its philosophy but also in its function and structure to meet political and scientific need of the modern society. The main purpose of this study is to develope the new concept of comprehensive nursing care, both its Philosophy and ethics, as the basic of modern clinical nursing theory and practice. Comprehensive nursing care is the concept of human centered nursing care, and it helps a man to meet the basic physical, psychological, environmental, socioeconomic and teaching needs. It also helps him to help himself to meet these needs. This concept starts from the individualized nursing care and its ultimate goal is to improve a man to have a better position in his own community so that he may able to have a meaningful life. To accomplish this goal, an individualized nursing care plan as a nursing diagnosis and problem solving method should be set up for different patients with similar diagnosis to meet their needs, because each patient has a different social background. from this viewpoint, nursing is a science as well as abstruse humanity. The performance of comprehensive nursing care is a goal and issue of modern clinical nursing care. If nursing is a science and a profession for man, it should have ethics which recognize the dignity of man and offers infinite service voluntarily, and should be able to show leadership in carrying out the nursing responsibility. This leadership finds a person's potential and encourages him to utilize it. Such concepts should develop into a nursing ideology and this ideology should become a priority in comprehensive nursing care. The following statements are the conclusion of this study. 1) Modern nursing has been developed from disease centered nursing care to comprehensive nursing care based on humanity. The primary principle of nursing was to assist in the treatment of disease, but it has been changed to the professional nursing system independently. 2) The concept of nursing is one of continuous or endless scope of dispersion. It proves that nursing is grasping the professional responsibility to be able to coordinate scientific principles Patient health problems are according to scientific principles rather than adhering to nursing technical discipline as a daily work. 3) In chapter I and Ⅱ, the philosophy and ideology of nursing have been discussed and the flow of concept of clinical nursing and the rate of progress which emerges from naturalizing performance of the concept of comprehensive nursing in clinical nursing studied. The discussion developed the theory that a nurse should be to embody nursing ideas and objectives by establishing definite conviction of professions and study. 4) In chapter lil, nursing planning based on nursing diagnosis as a method to attain ideal nursing care for humanity with a definite idea of establishing philosophy of nursing was presented. 5) From the result of survey on patient needs about treatment and nursing, it was observed that all patient had emotional stress from unknown factors. Therefore it was concluded that nurses should not only educate the patient but also give them the opportunity to communicate freely their needs and anxieties. Furthermore complaints and doubts of the patient should be carefully noted and must be considered to meet these needs. 6) Patient teaching is the most important part of comprehensive nursing care. In chapter, Ⅲ, the important of patient teaching was emphasized by demonstrating the effect of patient teaching for diabetic patient. 7) In Chapter Ⅳ, from the result of the study on nurses attitudes to comprehensive nursing care, it was pointed that the evolution of nursing education and the establishment of a complete concept and value of comprehensive nursing was necessary.

• 한국축산시설환경학회지
• /
• 제10권1호
• /
• pp.1-10
• /
• 2004

현장규모 (8.6${\times}$2.5${\times}$2.4 m) 및 파이롯트규모 (1.39${\times}$0.89${\times}$0.89 m)의 고온호기산화장치를 이용하여 공기투입량 및 처리온도에 따른 양돈분뇨의 감량화 효율을 검토하였다. 현장규모에서 공기투입장치, 거품제거장치의 설치조건이 양돈슬러리 증발량과 처리온도에 모두 영향을 미치고 있음을 알 수 있었다. 현장규모 연구는 3가지의 처리방법 (처리A:공기공급량 120㎥/h, 수중펌프 2대, 소포장치2대: 처리 B: 공기공급량 180㎥/h, 수중펌프 3대, 소포장치 3대; 처리C: 공기공급량 180㎥/h, 수중펌프 3대, 소포장치 4대)으로 실행되었다. 1일 5㎥ 양돈슬러리를 동일하게 투입하면서 얻어진 연구결과, 수위변화, 온도변화 및 증발량은 각각 처리A: 50∼100cm, 31∼$64^{\circ}C$, 55L/$\m^2$ㆍday, 처리B: 40∼90cm, 29∼$52^{\circ}C$, 75L/$\m^2$ㆍday, 처리C: 40∼70cm, 45∼$54^{\circ}C$, 120L/$\m^2$ㆍday이었다. 한편 파이롯트 규모 연구는 반 연속식으로 양돈분뇨를 투입하면서 매일 투입량을 처리1: 50L/2h, 처리2: 50L/3h, 처리3: 40L/3h, 처리4: 60L/4h으로 하여 최대 슬러리 감량조건을 도출하기 위해 수행하였다.

• Pediatric Infection and Vaccine
• /
• 제7권2호
• /
• pp.225-232
• /
• 2000

목 적 : 올바른 항생제의 사용을 위해서는 우선 항생제 사용 실태의 파악과 함께 검사실의 확충, 의료진의 협조 등 다양한 노력과 보완이 요구된다. 본 연구는 적절한 항생제 사용의 기반을 마련하고자 현재 시행되고 있는 항생제 사용 실태를 조사하였다. 방 법 : 전북대학교병원에 입원한 환자 총 1,833명을 대상으로 의무기록을 통하여 항생제의 사용 여부, 종류, 사용 기간, 용량, 항생제의 투약 시작 시기 및 투여 목적을 조사하였다. 결 과 : 전체 조사 대상 환자 1,833명 중 입원 기간 중 항생제를 사용한 환자는 1,231명으로 67.2%였으며, 계별로 살펴보면 내과계는 전체 1,014명 중 497명(49.0%)이 항생제를 사용하였고, 외과계는 819명 중 734명(89.6%)에서 항생제를 사용하였다. 전체 항생제를 사용한 환자 1,231명 중 706명(57.4%)에서 예방 목적으로 사용하였고, 525명(42.6%)에서 치료 목적으로 사용하였다. 항생제를 사용한 환자의 경우 사용된 항생제의 갯수를 살펴보면 총 1,231명 중 1가지 항생제를 사용한 경우는 125명(10.2%)이었으며, 2가지를 사용한 경우는 311명(25.3%), 3가지를 사용한 경우는 562명(45.6%), 4가지 이상을 사용한 경우는 233명(18.9%)으로, 70% 이상의 환자에서 3가지 이상의 항생제가 사용하였다. 사용 항생제의 종류는 ${\beta}$-lactam, aminoglycoside, quinolone, macrolide, 항진균제, metronidazole, clindamycin, trimethoprim-sulfamethoxazole, glycopeptide, 그리고 fosfomycin 등으로 아주 다양하였다. 전체적인 그룹별 사용률을 보면 ${\beta}$-lactam은 57.0%, aminoglycoside는 34.5%, quinolone은 3.6% 그리고 기타 그룹은 4.9%로, ${\beta}$-lactam과 aminoglycoside가 가장 많이 사용되었다. 결 론 : 대부분의 환자에서 2가지 이상의 항생제의 병합요법이 보편화되어 있다는 점은 진지하게 검토되어야 할 것으로 생각된다. 아울러 임상적으로 전신 세균 감염이 확실한 경우에도 원인 병원체를 찾아내기 위한 적극적인 노력이 부족한 경우도 상당수 있어 이에 대해서도 검사실과 함께 적극적인 개선의 노력이 필요할 것으로 생각된다. 수술 환자의 예방적 화학 요법에 대해서도 개선이 필요할 것으로 생각된다.

• 한국작물학회지
• /
• 제36권3호
• /
• pp.214-219
• /
• 1991

관계수온에 따른 벼 품종들의 출수일수, 주간엽 전개 소요일수, 주간총엽수 등을 조사하여 수온과 벼 품종들의 출수특성과의 관계를 구명하고자, 삼강벼 등 12개 품종을 공시하고, 찬물계속 흘려대기를 실시하여 동일 포장 내에서 수온의 차이를 둔 벼 내냉검정포에서 시험을 수행한 결과를 요약하면 다응과 같다. 1. 담수심을 5 cm로하여 찬물계속흘려대기를 실시할 때 관계수 정체시간은 3 시간 이었으며, 포장 내의 수온은 찬물유입구로부터 배수고를 향하여 거리가 밀어질수록 상승되었다. 대체로 기온이 높아짐에 따라 수온도 높아지는 경향이었고, 배수구 쪽의 수온은 벼의 영양생장기에는 기온보다 높았지만, 생식성장기에는 낮았다 2. 수온 상승에 따라서 주간엽의 전개속도는 빨라지는 경향이었으며, 품종별로는 복광벼, 상풍벼, YR3486-16-2 등은 민감하였으나 Janack, 밀양4002 등은 다소 둔감한 편이었다 3. 영양생장기에 비하여 생식성장기에 1엽전개 소요일수가 두드러지게 늘어난 품종은 Janack, Paro-white 등이 었 다. 4. 1엽전개 소요일수의 품종간 차이는 수온이 높았던 영양생장기보다 상대적으로 수온이 낮았던 생식성장기에 켰다 5. 수온이 비슷한 조건일 때 수온의 차이에 의한 전체 공시품종의 평균 1엽전개소요일수의 영양생장기와 생식생장기의 생육단계간 차이는 인정되지 않았으며, 수온 13$^{\circ}C$-23$^{\circ}C$ 범위에서는 1$^{\circ}C$ 상승에 따라 1.3 일만큼 감소하는 것으로 추정 되었다. 6. 수온에 따른 주간총엽수의 증감은 품종간에 차이가 있었다. 수온이 상승됨에 따라 1 엽이 증가된 품종은 복광벼, 광명벼, China 988, YR3486-16 등이었고, 주간총엽수의 변화가 없었던 품종은 소백벼, Paro-white, 상풍벼, 풍산벼, 삼강벼, 밀양4002 등이었다 7. Janack 품종은 수온의 상승에 따라 주간총엽수가 증가되면서, 출수일수도 늘어났지만, 그밖의 품종들은 수온 차이에 의한 주간총엽수의 변화와는 관계없이 수온 상승에 따라 출수일수가 단축되었는데, 그 정도는 품종마다 달랐다.

• 지능정보연구
• /
• 제27권4호
• /
• pp.23-48
• /
• 2021

한국경제는 지난 수십년간 정부의 수출전략정책에 힘입어 지속적으로 경제 성장을 이룩해왔으며, 수출의 증가는 경제의 효율성 향상, 고용창출, 기술개발 촉진 등 우리나라의 경제 성장을 견인하는 주도적인 역할을 해왔다. 전통적으로 우리나라 수출에 영향을 미치는 주요 요인은 크게 경제적 요인과 산업구조적 요인이라는 두가지 관점에서 찾아볼 수 있다. 첫번째, 경제적 요인은 환율과 글로벌 경기 변동과 관련된 것으로서, 환율이 우리나라 수출에 미치는 영향은 환율 수준 및 환율 변동성에 따른 영향으로 나누어 살펴볼 수 있으며, 글로벌 경기 변동은 세계 수입 수요에 영향을 미쳐 우리나라 수출을 좌우하는 절대적 요인으로 볼 수 있다. 두 번째, 산업구조적 요인은 국제 분업화의 둔화, 중국의 특정 수입품 자국내 대체 증가, 수출 주력 산업의 해외생산 형태 변화 등 산업이나 제품에 따라 발생한 고유한 특징이다. 가장 최근 글로벌 교류와 관련된 연구들을 살펴보면, 경제적 요인 및 산업구조적 요인과 더불어 문화적인 측면이 중요함을 여러 문헌에서 피력하고 있다. 이에 따라 본 연구에서는 각국의 한국 수입액 예측 모형에 문화적 요인을 함께 반영하여 예측 모형을 개발하고자 하였으며, 구체적으로 문화적 요인이 수입액에 미치는 영향을 PUSH-PULL 프레임워크 관점에서 반영해보고자 하였다. PUSH 관점은 한국이 자신의 브랜드를 개발하고 적극 홍보하는 관점으로 K-POP, K-FOOD, K-CULTURE 등으로 대표되는 한국의 브랜드에 대한 각국의 관심 정도로 정의할 수 있다. 또한, PULL 관점은 각 국가의 국민들의 문화적, 심리적 특징으로 해당 국가의 지배체계, 남성성, 위험 회피성, 시간에 대한 단기/장기 지향성 등으로 대표되는 각 국의 문화 코드로서 한류문화를 얼마나 수용할 성향을 띄고 있는지로 정의할 수 있다. 본 연구에서 제시한 최종 예측 모델의 고유한 특징은 Design Principle에 기반하여 설계한 것인데, 1) 신규로 추가한 데이터 소스를 통해 한국에 대한 관심 및 문화적 특성이 반영될 수 있는 모형으로 구축하였고, 2) 경제적 요인 등의 변화와 품목 및 국가 Code를 입력하면 예측값을 바로 불러올 수 있도록 실용적으로 편의성 있게 설계하였으며, 3) 이론적으로도 의미 있는 결과를 도출하기 위해서 입력과 목표 변수간의 관계를 해석 가능한 알고리즘을 중심으로 설계하였다는 점이다. 본 연구는 기술적 측면, 경제적 측면, 정책적 측면에서 의미 있는 시사점을 제시할 수 있으며, 수입액 예측 모형을 활용하여 중소·중견기업의 수출 지원 전략에 의미 있는 기여를 할 수 있을 것으로 기대된다.