• Current Optics and Photonics
• /
• 제6권4호
• /
• pp.400-406
• /
• 2022

We numerically demonstrate that the inherent spiking behavior in the quasi-continuous-wave (QCW) operation of an Nd:YAG laser can be suppressed by adopting bias pumping. After spiking suppression, the output QCW pulses from a bias-pumped Nd:YAG laser are very stable, and they can maintain nearly the same temporal shape as that of pump pulse under different pump repetition rates and peak powers. Our study implies that bias pumping is an alternative method of spiking suppression in solid-state lasers, and the application areas of an Nd:YAG laser may be extended by bias pumping.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.437-438
• /
• 2009

• 한국정밀공학회지
• /
• 제21권11호
• /
• pp.53-60
• /
• 2004

Laser welding techniques have been characterised for various materials. In this paper, the laser weldability of STS304 stainless steel and Inconel 600 at dissimilar metal welds using a continuous wave Nd:YAG laser are experimentally investigated. Inconel 600 is being used in a steam generator tubing of pressurized water reactor(PWR) exposed to some corrosion. Stress corrosion cracking can occur on this material. An experimental study was conducted to determine effects of welding parameters, on eliminating or reducing the extent welding zone formation at dissimilar metal welds and to optimize those parameters that have the most influence parameters such as focus length, power, beam speed, shielding gas, and wave length of laser were tested.

• 한국군사과학기술학회지
• /
• 제17권1호
• /
• pp.82-89
• /
• 2014

The damage in germanium (Ge) optical window irradiated by a near-infrared continuous wave (CW) laser was studied. Laser-induced heating and melting process were surveyed, and the specific laser power and the irradiance time to melt were estimated by numerical simulation. The experiments were also carried out to investigate the macro and micro structure change on Ge window. Results showed that the surface deformation was formed by melting and resolidification process, the damaged surface had a polycrystalline phase, and the transmittance as an optical performance factor in mid-infrared region was decreased. We confirmed that an abnormal polycrystalline phase and surface deformation effect such as hillock formation and roughness increase reduced the transmittance of Ge window and were the damage mechanism of CW laser induced damage on Ge window.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.644-650
• /
• 2012

This paper show the 2kW fiber laser cutting properties of SS400. The study was comparison of traditional 4kW $CO_2$ Laser cutting and 2kW Fiber laser cutting characteristics for the application of Industrial 2D Laser Cutting Machine. The laser used in this investigation was an IPG YLU-2000 multi-mode Ytterbium Fiber machine with a maximum power of 2000W and a wave length of 1070 nm. The laser was used in its Continuous Wave (CW) mode with an approximately top hat beam intensity distribution. Fiber laser high quality cuts at a large range of speeds (ranging from 2000 to 3800 mm/min) which has been obtained for the 2.3mm Sheet of SS400. 2kW power Fiber laser cut was able to max. 20mm sheets of SS400 (speed range from 650 to 850 mm/min). Fiber laser cutting used in conventional hole nozzle could cut 12mm SS400 but used in special dual cutting nozzle could cut 20mm SS400.

• 한국재료학회지
• /
• 제30권7호
• /
• pp.327-332
• /
• 2020

Laser induced surface activation (LISA) technology requires refined selection of process variables to fabricate conductive microcircuits on a general polymer material. Among the process variables, laser mode is one of the crucial factors to make a reliable conductor pattern. Here we compare the continuous wave (CW) laser mode with the pulse wave (PW) laser mode through determination of the surface roughness and circuit accuracy. In the CW laser mode, the surface roughness is pronounced during the implementation of the conductive circuit, which results in uneven plating. In the PW laser mode, the surface is relatively smooth and uniform, and the formed conductive circuit layer has few defects with excellent adhesion to the polymer material. As a result of a change of laser mode from CW to PW, the value of Ra of the polymer material decreases from 0.6 ㎛ to 0.2 ㎛; the value of Ra after the plating process decreases from 0.8 ㎛ to 0.4 ㎛, and a tight bonding force between the polymer source material and the conductive copper plating layer is achieved. In conclusion, this study shows that the PW laser process yields an excellent conductive circuit on a polymeric material.

• 한국광학회지
• /
• 제9권4호
• /
• pp.240-244
• /
• 1998

공동 광자 감쇠 분광법(cavity ring down spectroscopy, CRDS)은 미량기체의 절대밀도를 측정할 수 있는 고감도 레이저 분광기술이다. 연속발진 레이저(continuous wave laser)를 사용한 새로운 방법의 CRDS 분광기를 구현하였다. 이 장치에서는 PZT(piezoelectric transducer)를 움직여 공동의 길이를 비공명(off-resonance)상태로 빠르게 변화시킴으로써 입사되는 연속발진 레이저 빔을 차단하여 감쇠신호를 발생시킨다. 이 방법으로 570 nm 근처에서 압력이 2700 Pa인 아세틸렌(C2H2)의 overtone 천이에 대한 흡수 분광선을 측정하였으며, 이때 측정할 수 있는 최소 흡수계수는 3$\times$10-9 cm-1정도이다.

• Journal of the Optical Society of Korea
• /
• 제17권1호
• /
• pp.5-9
• /
• 2013

We report on high-power continuous-wave operations of an Er:YAG ceramic laser in-band pumped by a cladding-pumped Er,Yb fiber laser at 1532 nm. With an output coupler of 10% transmission, the ceramic laser yielded 16.7 W of continuous-wave output at 1645 nm for 28.8 W of incident pump power, corresponding to a slope efficiency of 61.0% with respect to the incident pump power. The lasing wavelength switched to 1617 nm when output couplers of > 20% transmission were used. Up to 16.2 W of 1617 nm output was generated for 33.0 W of incident pump power, corresponding to a slope efficiency of 51.8%. Graphene Q-switched operation of Er:YAG cermic laser at 1645 nm was also demonstrated with stable pulses of 30-74 kHz repetition rates and 1.5-6.4 ${\mu}s$ pulse widths.

• Current Optics and Photonics
• /
• 제5권3호
• /
• pp.306-310
• /
• 2021

A 200-W continuous-wave thulium-doped all-fiber laser at 2050 nm was developed with a master oscillator power amplifier configuration. For the master oscillator, a single-mode thulium-doped fiber laser was built with fiber Bragg gratings. The operating power of the oscillator was 10.1 W at a pump power of 20.9 W, and the slope efficiency was measured to be 53.0%. All emitted wavelengths of the oscillator were located between 2049.2 nm and 2049.9 nm, and no other peaks in different wavelength ranges were observed. The maximum output power of the final amplified beam was 204.6 W at a pump power of 350.4 W. The slope efficiency of the amplifier was measured to be 58.4%.

• 비파괴검사학회지
• /
• 제33권4호
• /
• pp.317-322
• /
• 2013

This paper presents a new laser lock-in thermography (LLT) technique for nondestructive evaluation. LLT utilizes a modulated continuous wave laser beam as a heat source to obtain high fidelity thermal wave images even at the presence of background heat disturbances. The thermal waves propagating along the surface and through-the-thickness directions of a structure are visualized using newly developed laser lock-in amplitude and phase images, enhancing the detectability of surface and subsurface defects. The LLT technique is numerically investigated and experimentally validated using thermal images obtained from a steel specimen with low emissivity.