• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.290-291
• /
• 2001

The relationship between velocity, viscosity, diffusion coefficient, mass transfer coefficient and characteristic length and mass transfer data can be correlated by dimensionless relationship in electrolytic process. The performance of dyestuff removal was decreased as the flow rate of electrolyte was increased. It was due to the effect of retention time decreasing was superior to that of turbulent inlet mixing. Sh/Sc$\^$1/3/ vs Re plot for Al flat electrode did not showed the general tendency of the relationship between Sh/Sc$\^$1/3/ and Re. It can be thought that flow rate was not sufficiently high to increase the effect of mixing.

• Design & Manufacturing
• /
• v.16 no.2
• /
• pp.26-32
• /
• 2022

It is known that the fluidized bed incinerator, which is the subject of analysis, shows excellent performance in heat and mass transfer due to excellent mixing and contact performance between fluidized sand and fuel, and also shows relatively good combustion characteristics thanks to good mixing and long residence time for low-grade fuels. have. In this study, air flow analysis is performed to understand the characteristics of co-firing of sludge, waste oil and solid waste in the fluidized bed incinerator, flow characteristics of flue gas, and discharge characteristics of pollutants.The fluidized bed incinerator subject to analysis is a facility that incinerates factory waste and general household waste together with sludge, with a processing capacity of 32 tons/day. to be. In addition, the operation method was designed for continuous operation for 24 hours. As a result, it can be seen that the lower combustion air and the introduced secondary air are changed to a strong turbulence and swirl flow form and exit through the outlet while rotating inside the freeboard layer. The homogeneous one-way flow form before reaching the secondary air nozzle has very high diffusivity with the high-speed jet flow of the nozzle.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.170-171
• /
• 2022

In recent years, due to the occurrence of traffic accidents caused by black ice in winter, the number of personal injuries is increasing rapidly. Black ice is a phenomenon that occurs like a thin layer of ice on the road surface. Accordingly, many developments of heat-generating concrete are being developed to remove ice by increasing the temperature by supplying constant electricity to places where black ice is likely to occur. These heating elements are being developed by mixing a conductive material represented by carbon nanotubes with concrete. However, research up to now has been focused on efficient temperature rise and derivation of the optimum mixing ratio, and the evaluation of maintaining heat generation performance during continuous repetition is insufficient. Therefore, in this study, a heating test specimen was manufactured and 50V power was repeatedly supplied to evaluate the heating characteristics.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.1
• /
• pp.34-51
• /
• 2020

In order to clarify the lime-based building method used in the Joseon Dynasty, lime materials, production techniques, and mixing methods recorded in ancient literature were examined. In ancient Joseon Dynasty literature, the use of low grade limestone as a raw material was recorded, and the use of pozzolanic materials such as Hwangtoh, white clay, and roof tile powder as mixing aids to enhance the strength of lime was recorded. In addition, various lime hydration and mixing methods were recorded, and based on re-experiments carried out with regards to this, a physical property evaluation was deemed to be required in accordance with the various types of raw lime materials, lime hydration methods, and mixture ratios. In the early Joseon Dynasty, lime was used for various aspects, but frequent problems were experienced due to lack of supply and poor production techniques. In the late Joseon Dynasty, lime production techniques developed along with mass production. Based on analysis of the manufacturing techniques of Hoegwagmyo lime mortar in the 16^th and 18^th centuries during the Joseon Dynasty, it was found that mixing ratios and the methods described in the ancient literature had been applied. It was confirmed that the mixing ratio differed depending on mixing materials and lime quality. Since the mixing ratio of Hoegwagmyo lime mortar changed over time and it was produced strictly on the basis of a guidebook, it is believed that if continuous scientific analysis of the Hoegwagmyo lime mortar production method were carried out, this would be helpful for ascertaining the chronological methodology of Hoegwagmyo.

• The Journal of the Petrological Society of Korea
• /
• v.1 no.2
• /
• pp.91-103
• /
• 1992

Eruptive mechanisms and processes at Udo tuff cone can be inferred from indicative characters of products, bedforms and lithofacies, and ring faults. In terms of bedforms and lithofa-cies in particular, massive lapilli tuff beds and chaotic lapilli tuff beds are derived from subaerial falls of aggregated tephra of wet tephra finger jets, occurring dominantly at the lower sequences of proximal part at the tuff cone. Crudely stratified lapilli tuff are derived from subaerial falls of slightly aggregated tephra of less wet tephra finger jets, whereas reversely graded lapilli tuff beds are from slightly disaggregated subaerial falls of continuous uprush. Both beds frequently occur in the middle sequences at proximal and near medial part of the tuff cone. Block and lapilli tephra lenses, ash-coated lapilli tephra beds(lenses) and thin-bedded tuff beds are derived from extremely disaggregated subaerial falls of dry tephra in the continuous uprush, frequently occurring at the upper sequences of medial part at the tuff cone. Udo tuff cone is a basaltic volcano emergent through the sea water surface while water could flood across or into the vent area. Emergence of the tuff cone was from the type-Surtseyan eruption characterized by earlier tephra finger jets and later continuous uprush columns of tephra with copious volumes of steam. Explosions began when boiling of wter produced a bubble column reducing the hydrostatic pres-sure, allowing exsolution of gases from the magma. This expansion of magma into a vesiculating froth fragmented the magma and permitted mixing of magma and water so that a more vigorous generation of steam could proceed. Tephra finger jetting explosions continued to build the crater rims, then remove water from the vent that their deposits flowed like slsurries until the continuous uprush explosion ensued. Continuous uprush explosions were associated with most rapid accumula-tion of tephra. The increasing volume rate led to partial removal of water from the vent area by the newly tephra ring so that more vigorous activity could be attended by a reducing water supply. This might restrain surplus of cold water entering the vent and thus enhance the vigour of the eruption by allowing optimal heat exchange. Eventually the crater became so deep and unsuported that piecemeal sliding, or massive subsidence on indipping ring faults, filled and closed the vent, and the cycle of explosions and collapse began anew.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.9 no.6
• /
• pp.454-458
• /
• 2004

A study of the POSE (predispersed solvent extraction) for succinic acid by colloidalliq­uid aphrons was conducted. The organic phase contaning TOA (tri-n-octylamine) and 1-octanol permits a selective extraction of succinic acid from its aqueous solution. There was no difference of the extractability of POSE and that of conventional mixer-settler type extraction. Taking into account the no mechanical mixing in POSE, it was concluded that the POSE process is more adaptive than the conventional mixer-settler type extraction process. From mass transfer analysis at the various concentration of TOA in counter-current continuous operation, the concentration of TOA had no influence on the mass transfer coefficient. The loading values in continuous POSE were almost same as those in batch operation.

• Journal of the Korea Society for Simulation
• /
• v.2 no.1
• /
• pp.78-90
• /
• 1993

기존의 모의 실험언어를 이용해서 연속 체계를 모의 실험하는 것을 사용자가 언어에서 요구하는 형태로 모델을 형성해야 하는 어려움이 따른다. 따라서 본 연구에서는 사용자에게 최대한 편의성을 제공하는 연속체계 모의 실험언어인 PCSL (Postech Continuous -system Simulation Language)를 개발하였다. PCSL은 주어진 대상을 모델링한 미분방정식과 그것을 푸는데 필요한 여러 가지 제약 사항으로 이루어진 간단한 프로그램을 입력으로 받아 자동으로 모의 실험을 수행함으로서 사용자의 노력이 최소화하게 된다. PCSL 처리 시스템의 구성은 주어진 모델을 C 프로그램으로 변형하는 변환기, 모의 실험 알고리즘을 구현한 C 프로그램을 생성하는 생성기, 모의 실험을 수행하는 실행기, 사용자 인터페이스 등으로 되어있다. 구현 예로는 먼저 선형 상미분방정식의 예로 mass-damper-spring system, 비선형 상미분방정식의 예로 van der Pol 방정식, 연립 상미분방정식의 예로는 mixing tank problem 등을 보였다.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.1
• /
• pp.44-53
• /
• 2008

An interacting multiple model (IMM) estimation algorithm based on the mixing of the predicted state estimates is proposed in this paper for a right continuous jump-linear system model different from the left-continuous system model used to develop the existing IMM algorithm. The difference lies in the modeling of the mode switching time. Performance of the proposed algorithm is compared numerically with that of the existing IMM algorithm for noisy system identification. Based on the numerical analysis, the proposed algorithm is applied to target tracking with a large sampling period for performance comparison with the existing IMM.

• Journal of the Korean Mathematical Society
• /
• v.60 no.2
• /
• pp.255-271
• /
• 2023

In this paper, we deal with random attractors for dynamical systems forced by a deterministic noise. These kind of systems are modeled as skew products where the dynamics of the forcing process are described by the base transformation. Here, we consider skew products over the Bernoulli shift with the unit interval fiber. We study the geometric structure of maximal attractors, the orbit stability and stability of mixing of these skew products under random perturbations of the fiber maps. We show that there exists an open set U in the space of such skew products so that any skew product belonging to this set admits an attractor which is either a continuous invariant graph or a bony graph attractor. These skew products have negative fiber Lyapunov exponents and their fiber maps are non-uniformly contracting, hence the non-uniform contraction rates are measured by Lyapnnov exponents. Furthermore, each skew product of U admits an invariant ergodic measure whose support is contained in that attractor. Additionally, we show that the invariant measure for the perturbed system is continuous in the Hutchinson metric.

• KSBB Journal
• /
• v.20 no.6
• /
• pp.438-442
• /
• 2005

Batch experiments were performed to investigate the effects of volumetric mixing ratio(v/v) of two substrates, food wastes(FW) and waste activated sludge(WAS). In batch experiments, optimum mixing ratio for hydrogen production was found at $10{\sim}20$ v/v % addition of WAS. CSTR(Continuous Stirred tank reactor) was operated to investigate the hydrogen productivity and the microbial community under various HRTs and volumetric mixing ratio(v/v) of two substrates. The maximum yield of specific hydrogen production, 140 mL/g VSS, was found at HRT of 2 day and the volumetric mixing ratio of 20:80(WAS:FW). The spatial distribution of hydrogen producing bacteria was observed in anaerobic fermentative reactor using fluorescent in situ hybridization(FISH) method.