• Korean Journal of Metals and Materials
• /
• v.48 no.4
• /
• pp.277-288
• /
• 2010

The hot corrosion properties of heat-resistant steels were investigated in an oxidation atmosphere including artificial ash and sulfur dioxide. The heat-resistant steels of T22, T92, T122, T347HFG, Super304H and HR3C were evaluated at 620, 670 and $720^{\circ}C$ for 400 hours. The relationship between the corrosion rate and the temperature followed a bell-shaped curve with a peak rate at around $670^{\circ}C$. The corrosion rates showed a decreasing tendency as the chrome contents of these steels increased from 2.15 wt.% to 24.5 wt.%, and austenitic steels had a lower corrosion rate than ferritic steels. Sulfidation by $SO_2$ as well as molten salt corrosion also had an effect on the total corrosion rate, especially showing an increase in the corrosion rate in ferritic steels. Regardless of the chrome content in the steels and irrespective of the test temperature, the corrosion scale was composed of an outer oxide and an artificial ash mixed layer, a middle oxide layer and inner sulfide, and a mixed oxide layer. As the chrome content increased, the proportion of chrome oxide in the corrosion scale increased. Before spalling of the corrosion scale, voids and cracks were initiated in the sulfide and the mixed oxide layer or at the interface with the substrate.

• Archives of Metallurgy and Materials
• /
• v.66 no.3
• /
• pp.695-698
• /
• 2021

Influence of Si addition on oxide layer growth of Al-6 mass%Mg alloys in molten state was investigated in this study. After melt holding for 24 h, the melt surface of only Si-free alloy became significantly bumpy, while no considerably oxidized surface was observed even with 1 mass%Si addition. There was no visible change on the appearance of melt surfaces with increasing Si content. As a result of compositional analysis on the melt samples between before and after melt holding, the Si-added alloys nearly maintained their Mg contents even after the melt holding for 24 h. On the other hand, the Mg content in the Si-free alloy showed a great reduction. The bumpy surface on Si-free alloy melt showed a large amount of pores and oxide clusters in its cross-section, while the Si-added alloy had no significantly grown oxide clusters on the surfaces. As a result of compositional analysis on the surfaces, the oxide clusters in Si-free alloy contained a great amount of Mg and oxygen. The oxide layer on the Si-added alloy was divided into Mg-rich and Mg-poor areas and contained certain amounts of Si. Such a mixed oxide layer containing Si would act as a protective layer during the melt holding for a long duration.

• Journal of the korean society of oceanography
• /
• v.31 no.4
• /
• pp.196-206
• /
• 1996

Vertical profiles of the chlorophyll ${\alpha}$, phytoplankton abundance, nutrients and sigma-t were compared with the vertical distribution of phytoplankton species in conjunction with $^{14}$C primary production in the Southern Waters of the East Sea, Korea. In the upper mixed layer the water column was only weakly stratified and ambient nitrogenic nutrient concentrations were markedly depleted. Dissolved silicate seemed to be another limiting nutrient in the surface layer. The occupation of different water depths by several dominant diatom species was well explained by the degree of silicification of each cell and the silicate concentration of ambient seawater. Subsurface chlorophyll maxima were continuously observed in the lower parts of the euphotic layer and the depth coincided with nutricline, supporting our view that chlorophyll maximum was sustained partially by enhancement of in situ growth of phytoplankton and partially by increase of cellular chlorophyll content. The persistence of chlorophyll maximum layer was attributed to the physiological adaptation of the phytoplankters to low light intensities and to the utilization of regenerated nutrients. Integrated water column production of organic matter by photosynthesis appeared to be better related to phytoplankton cell division than to the cell growth in terms of biosynthesis of pigments and other intracellular components.

• Korean Journal of Materials Research
• /
• v.27 no.8
• /
• pp.409-415
• /
• 2017

For enhanced cavitation erosion resistance of vessel propellers, an electroless Ni-P plating method was introduced to form a coating layer with high hardness on the surface of Cu alloy (CAC703C) used as vessel propeller material. An electroless Ni-P plating reaction generated by Fe atoms in the Cu alloy occurred, forming a uniform amorphous layer with P content of ~10 wt%. The amorphous layer transformed to (Ni3P+Ni) two phase structure after heat treatment. Cavitation erosion tests following the ASTM G-32 standard were carried out to relate the microstructural changes by heat treatment and the cavitation erosion resistance in distilled water and 3.5 wt% NaCl solutions. It was possible to obtain excellent cavitation erosion resistance through careful microstructural control of the coating layer, demonstrating that this electroless Ni-P plating process is a viable coating process for the enhancement of the cavitation erosion resistance of vessel propellers.

• Korean Journal of Materials Research
• /
• v.23 no.9
• /
• pp.495-500
• /
• 2013

Mo-based thin films are frequently used as back electrode materials because of their low resistivity and high crystallinity in CIGS chalcopyrite solar cells. Mo:Na/Mo bilayer thin films with $1{\mu}m$ thickness were deposited on soda lime glass by varying the thickness of each layer using dc-magnetron sputtering. The effects of the Mo:Na layer on morphology and electrical property in terms of resistivity were systematically investigated. The resistivity increased from $159{\mu}{\Omega}cm$ to $944{\mu}{\Omega}cm$; this seemed to be caused by increased surface defects and low crystallinity as the thickness of Mo:Na layer increased from 100 nm to 500 nm. The surface morphologies of the Mo thin films changed from a somewhat coarse fibrous structures to irregular and fine celled structures with increased surface cracks along the cell boundaries as the thickness of Mo:Na layer increased. Na contents varied drastically from 0.03 % to 0.52 % according to the variation of Mo:Na layer thickness. The change in Na content may be ascribed to changes in surface morphology and crystallinity of the thin films.

• Geomechanics and Engineering
• /
• v.15 no.2
• /
• pp.783-791
• /
• 2018

In consideration of the mesoscopic structure of soil-rock mixtures in which the rock aggregates are wrapped by soil at normal temperatures, a two-layer embedded model of single-inclusion composite material was built to calculate the shear modulus of soil-rock mixtures. At a freezing temperature, an interface ice interlayer was placed between the soil and rock interface in the mesoscopic structure of the soil-rock mixtures. Considering that, a three-layer embedded model of double-inclusion composite materials and a multi-step multiphase micromechanics model were then built to calculate the shear modulus of the frozen soil-rock mixtures. Given the effect of pore structure of soil-rock mixtures at normal temperatures, its shear modulus was also calculated by using of the three-layer embedded model. Experimental comparison showed that compared with the two-layer embedded model, the effect predicted by the three-layer embedded model of the soil-rock mixtures was better. The shear modulus of the soil-rock mixtures gradually increased with the increase in rock regardless of temperature, and the increment rate of the shear modulus increased rapidly particularly when the rock content ranged from 50% to 70%. The shear modulus of the frozen soil-rock mixtures was nearly 3.7 times higher than that of the soil-rock mixtures at a normal temperature.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.4
• /
• pp.241-250
• /
• 1997

The velocity dispersion of surface acoustical wave(SAW) of Si layer/mesh Au/Si substrate was measured by the frequency analysis technique of backward radiation at liquid/solid interface. The difference of backward radiation patterns depending on used transducers (2, 5, 10MHz) confirmed that the backward radiation phenomenon was caused by the energy radiation from SAW generated in surface region. An ultrasonic goniometer was constructed to measure continuously the angular dependence of backscattered intensity. The angular dependences of backward radiation(5MHz) were measured for Ni layer/Al substrate specimens that were bonded by epoxy involving different content of Cu powder. It was known that the width and pattern of backward radiation had informations such as the velocity dispersion, bonding quality and structure of surface region.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1992.10a
• /
• pp.113-120
• /
• 1992

The construction of container terminal at Brani, Singapore required the improvement of soft clay layer having the thickness of about 6.5m, average moisture content of 79.4%, liquid limit of 90.4%, plastic limit of 21.8%, field vane strength of 10 to 25 KPa, pre-consolidation pressure of 225 to 60 KPa and compression index of 0.4 to 1.0. For the improvement of this layer, Colbon drains of 1.3m spacing in triangular pattern were installed to the bottom of the layer and surcharge of more than 11.25m high sand fill was later applied to the treated area. The settlement and lateral displacement of the ground were measured and the speed of surcharge filling was controlled, based on these readings. The removal of surcharge was determinied using the estimated time for the 90% degree of consolidation under the design pressure of 180KPa. The field and laboratory test results show that the soft clay layer has been improved substantially in its strength and consolidation characteristics: increase in strength of about 50KPa and pre-consolidation pressure and decrease in void ratio and compression index.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.87.1-87.1
• /
• 2011

For commercial applications, MEA development must be optimized in order to achieve high performance and low cost. There are many factors that affect the performance of MEA. Especially, the optimization of the method for preparing catalyst layer has great effect on the performance of MEA. Various methods have been used to prepare the catalyst layer of MEA. Among them, spraying method has a merit in that catalysis lay can be prepared with very flexible changes in catalyst layer as well as in the solvent composition of catalyst ink. In addition, in order to reduce the time required for manufacturing catalyst layer, an effort has been made to change the nozzle size and injection pressure of spray system. Further, the operation condition of spray system was changed in various ways in an effort to prepare optimum catalyst layer of MEA. Having optimized the operation condition of spraying system, comprehensive and diverse experiments were carried out concerning various factors that affect the performance of MEA. The present research report describes the results of more sub-categorized and more detailed experiments about the important factors (Nafion$^{(R)}$ ionomer, Relative humidity) which have been shown in previous experiments to exert greater effect on the performance of MEA.

• Journal of Surface Science and Engineering
• /
• v.33 no.1
• /
• pp.3-9
• /
• 2000

Arc-melted alloys of TiAl-(o.25, 0.5, 1.0at%) Si were isothermally oxidized at 800, 900 and $1000^{\circ}C$ in air for 60hr. It was found that the oxidation resistance of the prepared TiAl-Si alloys was much better than that of pure TiAl, being progressively increasing with an increase in the Si content. This was attributed to the formation of $SiO_2$in addition to ($TiO_2$+$Al_2$$O_3$) oxides which formed in TiAl alloys with and without silicon additions. However, the silica formation within the oxide layer unfortunately accelerated the oxide scale spallations. During oxidation, all the elements in the base alloy diffused outward, whereas oxygen from the atmosphere diffused inward. The oxides were primarily composed of an outer thick $TiO_2$layer, an intermediate diffuse $Al_2$$O_3$layer and an inner $TiO_2$layer. A small amount of $SiO_2$was present all over the oxide scale and some voids were found around the intermediate layer.