• Transactions of Materials Processing
• /
• v.27 no.1
• /
• pp.54-59
• /
• 2018

In connecting parts of a hydrogen fuel cell vehicle, since the rubber ring is permeable to hydrogen, it is necessary to use a metal sealing structure which ensures leakage stability. Finite element analysis was performed to verify the fitting characteristics of the metal sealing structure, which is used to connect the pipe to a high pressure hydrogen FCEV tank. Deformation shape, contact distance and axial load were compared experimentally and these values were in agreement with each other. In the contact surface, between the pipe and the fitting body, the stress at the edge of the contact surface was higher than the center point, which was considered to be a good characteristic in view point of the leakage. The location of the contact points has almost no change in the upper part of the fitting, but that of the lower parts move downward as the fastening amount increases. The contact pressure at the lower part is maintained at the same constant level.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.6
• /
• pp.577-585
• /
• 2015

We fabricated multi-scale such as macro-, micro-, and multi-scale wrinkles by using repetitive volume dividing (RVD) method and thermal curing process. Also wrinkle surface was modified with coating of a self-assembled monolayer (SAM). We measured the contact angle of each wrinkled surface, and observed the behavior of droplets on sloping surface. Through experimental study, we found out that the contact angle was much higher in case of multi-scale and SAM coated wrinkles. And micro-scale wrinkle showed a high contact angle comparing with that of macro-scale wrinkle. Dynamic behaviors of a water droplet like sliding velocity on diverse wrinkled surfaces were dependent on their static contact angles. These results showed that hydro-dynamic characteristics were changed depending on the wrinkle structure and the material forming the wrinkle. These dynamic characteristics can be utilized in bio-chip, microfluidics, and many others in order to control easily chemical reactivity.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.342-346
• /
• 2009

Forming characteristics for the bundle extrusion of Cu-Ti bimetal wires are investigated, which can identify the process conditions for weak mechanical bonding at the contact surface during the direct extrusion of a Cu-Ti bimetal wire bundle. Bonding mechanism between Cu and Ti is assumed as a cold pressure welding. Then, the plastic deformation at the contact zone causes mechanical bonding and a new bonding criterion for pressure welding is developed as a function of the principal stretch ratio and normal pressure at the contact surface by analyzing micro local extrusion at the contact zone. The averaged deformation behavior of Cu-Ti bimetal wire is adopted as a constitutive behavior at a material point in the finite element analysis of Cu-Ti wire bundle extrusion. Various process conditions for bundle extrusions are examined. The deformation histories at the three points, near the surface, in the middle and near the center, in the cross section of a bundle are traced and the proposed new bonding criterion is applied to predict whether the mechanical bonding at the Cu-Ti contact surface happens. Finally, a process map for the direct extrusion of Cu-Ti bimetal wire bundle is proposed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.8
• /
• pp.63-69
• /
• 2015

This paper presents the surface flashover characteristics to simulate the poor contact between an anode and a solid dielectric in a $N_2/O_2$ mixture gas (8/2) under a non-uniform field. The surface flashover voltage of the $N_2/O_2$ mixture gas revealed the irregular tendency that was not in accordance with the Paschen's law with an increasing gap of the poor contact. In addition, the insulation performance of the $N_2/O_2$ mixture gas at 0.6MPa was comparable to that of $SF_6$ gas of 0.1MPa based on the insulation performance on the poor contact. These results are able to apply the insulation design of eco-friendly gas insulation switchgear considering the internal faults.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.52-56
• /
• 2004

The movement of electron in the semiconductor-gap-semiconductor was observed by the variation of V-I characteristic as a distance two ZnO(1010) single crystals. When the resistance between two crystals was $10^2{\sim}10^4{\Omega}$, V-I characteristics had the pattern of the field emission or ohmic contact. On the other hand, when the resistance was larger than $10^7{\Omega}$ by increasing the distance between two crystals, the effect of surface barrier was prominent. This result leads to the conclusion that both the field emission (or ohmic contact) and the surface barrier effect including the tunneling have the influence on V-I characteristics of mechanically contacted crystals.

• KSTLE International Journal
• /
• v.2 no.1
• /
• pp.22-28
• /
• 2001

A resin bonded copper-graphite brush was investigated to evaluate the characteristics electrical signal transmission through a sliding contact as a function of the relative amount of graphite and copper in the brush. Particular attention was given to the correlation between electrical signal fluctuation and tribological properties in an electrical sliding contact system. A ring-on-block type tribotester was used for this experiment and the ring was made from pure copper. Results showed that a copper-graphite brush at a particular composition range exhibited the most stable frictional behavior with a minimum voltage drop. The amount of voltage drop at the friction interface was affected by the surface roughness, transfer film formation at the friction interface, and the real area of contact. Microscopic observations and the surface analysis showed a good agreement with the results from this experiment. The results also indicated that the electrical signal flunctuation was directly associated with the oscillation of the coefficient of friction during sliding by nanoscale variation of contacts at the friction interface.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.2
• /
• pp.149-151
• /
• 1997

Barrier height on the surface was monitored at 77 K by observing the inflection of V-I characteristics of ZnO(1010)-ZnO(1010) contact in the surface reaction of oxygen species with carbon monoxide. The contact showed inflections at 10-20 mV and 10-50 mV for the sample adsorbed oxygen at 298 K and 573 K, respectively. When the sample adsorbed oxygen at 573 K was exposed to carbon monoxide at 298 K and 573 K, inflections were observed at 10-40 mV and 10-30 mV, respectively. The results indicated that the adsorption of oxygen on ZnO increased the surface barrier height, and the reaction of carbon monoxide with the oxygen-preadsorbed (at 573 K) ZnO decreased the surface barrier height.

• Tribology and Lubricants
• /
• v.22 no.3
• /
• pp.119-126
• /
• 2006

In this paper, the contact behavior characteristics of a primary sealing components such as a seal ring and a seal seat has been presented for a small hydro-power turbine. Using the non-linear FEM analysis, the maximum temperature, the axial displacement, radial differences between a seal ring and a seal seat, and maximum contact normal stress have been analyzed for three optimized sealing profiles in which are designed based on the FEM analysis and Taguchi's experimental method. The three primary sealing profiles between a seal ring and a seal seat are strongly related to a leakage of a water for a hydro-power turbine and wear of a primary sealing component. The computed results show that the contact rubbing area between a seal ring and a seal seat is very important for reducing a friction heating and wear in a sealing gap, and increasing a contact normal stress in primary sealing components. Based on the FEM computation, models II and III in which have a small rubbing surface of seal rings show low dilatation of primary sealing components, and high normal contact stress between a seal ring and a seal seat. Thus, the FEM computed results recommend a short contacting width of a primary sealing component for reducing a leakage and thermal distortions, and expanding a seal life. This means that a conventional primary sealing component may be switched to a reduced sealing face of seal rings.

• Fashion & Textile Research Journal
• /
• v.15 no.2
• /
• pp.302-308
• /
• 2013

This study is a preliminary investigation of the influence of surface characteristics of substrates on detergency of particulate soil. The surface of PET film was modified with NaOH and NaOH+ethylene diamine on different times. The surface morphology of the film was scanned by AFM and surface energies were calculated from measured contact angles between several solutions and film based on the geometric mean and a Lewis acid base method. The surface morphology of PET film treated with NaOH and NaOH+ethylene diamine became more etched, and the surface area, surface roughness and the coefficient of friction of film increased with treatment of NaOH and NaOH+ethylene diamine. The contact angle of film treated with NaOH and NaOH+ethylene diamine decreased in water and surfactant solution; in addition, the surface energy increased was largely attributed to the increased portion on the polar surface energy of film. However, the effect of the diamine addition to the NaOH treatment solution on surface characteristics of PET film was insignificant.

• Journal of ILASS-Korea
• /
• v.20 no.3
• /
• pp.181-186
• /
• 2015

This study presents the dynamic wetting characteristics of an impact droplet on hole-patterned textured surfaces. The flat surfaces were manufactured by a drilling machine to generate the micro-order holes, leading to make the surface hydrophobic. Other flat surfaces were fabricated by the anodizing technique to make hydrophilic texture surfaces with a nanometer order. For hydrophilic and hydrophobic textured surfaces with similar texture area fractions, the impinging droplet experiments were conducted and compared with flat surface cases. As results, an anodized textured surface decreases apparent equilibrium contact angle and increases contact diameters, because of increase in contact area and surface energy. This is attributed to more penetration inside holes from larger capillary pressure on nanometer-order holes. On the other hand, temporal evolution of the contact diameter is smaller for the hydrophobic textured surface from less penetration on the micro-order holes.